Microwave Attenuators
Reduce the amplitude of microwaves without distorting waveform.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 18GHz SMA
60-802-208
Multiplexer Module
The 60-802-208 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI Single Microwave SPDT Relay 2.5GHz 75 1.6/5.6
40-780A-751
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
Product
LXI 75Ω 6:1 Microwave Multiplexer 8-bank 2.5GHz 1.6/5.6
60-820-008
Multiplexer Module
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 9-Bank 6GHz SMA
60-802-009
Multiplexer Module
The 60-802-009 is a 4-channel, 9-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40GHz, 50Ω, SMA-2.9
40-785C-443-TE
Multiplexer Module
The 40-785C-443-TE (PXI) and 42-785C-443-TE (PXIe) are triple SP4T 40GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Monolithic Microwave Integrated Circuit (MMIC) Amplifiers & Switches
-
Microsemi's portfolio of MMIC products targets a broad range of applications including those in electronic warfare, radars, instrumentation (test and measurement) and microwave communications. The portfolio comprises broadband amplifiers (both power and low-noise), amplifier modules, prescalers, attenuators and switches spanning DC to 65GHz based on high-performance process technologies. Microsemi offers 18 distributed amplifier products including industry-leading DC-65GHz MMICs. Microsemi's prescalers combine higher frequency operation, the flexibility to divide by a large number of ratios and very good residual phase noise.
-
Product
LXI Microwave Multiplexer, SP6T, 1-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-501
Multiplexer Module
Our 60-800-501 is a 1 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP4T, 7-Bank, 50GHz, 50Ω, SMA-2.4
60-803-707
Multiplexer Module
Our 60-803-707 is a 7 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PNA-X Microwave Network Analyzer
N5241A
Network Analyzer
Reach for unrivaled excellence in your measurements and designs Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the worlds widest range of single-connection measurement applications Test linear and nonlinear device characterization more accurately with the world's best PNA-X Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-451
Multiplexer Module
The 40-785C-451 (PXI) and 42-785C-451 (PXIe) are single SP4T 50GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
FieldFox Handheld Microwave Vector Network Analyzer
N9928A
Vector Network Analyzer
26.5 GHz max frequency Carry the world's most integrated handheld T/R VNA analyzer Expand your measurement flexibility with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and pulse power with a USB power sensor
-
Product
LXI 50Ω 6:1 Microwave Multiplexer 16-bank 40GHz SMA
60-800-416
Multiplexer Module
Our 60-800 Microwave Multiplexer range is suitable for switching 50 ohm signals up to 40GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 2.5GHz, 75Ω, 1.6/5.6
40-785C-752-E
Multiplexer Module
The 40-785C-752-E (PXI) and 42-785C-752-E (PXIe) are dual SP6T 2.5GHz unterminated 75Ω microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Microwave TV Transmitters for Radio Amateurs
-
Is the transmission of broadcast quality video and audio over the wide range of frequencies of radio waves allocated for radio amateur (Ham) use.[1] ATV is used for non-commercial experimentation, pleasure and public service events. Ham TV stations were on the air in many cities before commercial television stations came on the air.[2] Various transmission standards are used, these include the broadcast transmission standards of NTSC in North America and Japan, and PAL or SECAM elsewhere, utilizing the full refresh rates of those standards. ATV includes the study of building of such transmitters and receivers, and the study of radio propagation of signals travelling between transmitting and receiving stations.[
-
Product
LXI Microwave Multiplexer, SP4T, 1-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-501
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals up to 40GHz with automatic termination of unused signals
-
Product
LXI Microwave Multiplexer, SP4T, 12-Bank, 18GHz, 50Ω, SMA
60-803-112
Multiplexer Module
Our 60-803-112 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-215-001
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
Manual Attenuator (Waveguide)
-
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 4-Bank 40GHz SMA-2.9
60-802-404
Multiplexer Module
The 60-802-404 is a 4-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 18GHz, 50Ω, SMA, Terminated
40-785C-421-T
Multiplexer Module
The 40-785C-421-T (PXI) and 42-785C-421-T (PXIe) are single SP4T 18GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 18GHz, 50Ω, SMA, Remote Mount
40-785C-523-E
Multiplexer Module
The 40-785C-523-E (PXI) and 42-785C-523-E (PXIe) are triple SP6T 18GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Multiplexer, SP4T, 5-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-803-505
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals up to 40GHz with automatic termination of unused signals
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-005
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI Triple Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-533
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
LXI Microwave Multiplexer, SP4T, 3-Bank, 50GHz, 50Ω, SMA-2.4
60-803-703
Multiplexer Module
Our 60-803-703 is a 3 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
SmartPower® Intelligent Microwave Generators
-
SmartPower® AX2500 Series intelligent microwave power generators are built on proven experience in designing rugged, reliable microwave power generators for demanding semiconductor fabrication and industrial applications. The compact AX2500 design architecture incorporates field-proven technology, and combines new design features aimed at improved performance and lower cost of ownership.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 67GHz, 50Ω, SMA-1.85
40-780B-573
Relay
The 40-780B-573 (PXI) and 42-780B-573 (PXIe) are triple SPDT 67GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 2-Bank 6GHz SMA
60-802-002
Multiplexer Module
The 60-802-002 is a 4-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers.
