Digital Attenuators
-
product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
product
PXI Semi-Dynamic Digital I/O Module, 32-Channel
40-419-003
The 40-419-003 is a 32-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Astronics PXIe-6943, 1-Slot, 50 MHz, 32-Channel PXI Digital Pattern Instrument
785855-01
1-Slot, 50 MHz, 32-Channel PXI Digital Pattern Instrument - The Astronics PXIe-6943 works as a core component of digital test systems that may include switching, analog instrumentation, and an RF subsystem. This instrument features an advanced thermal design, temperate monitoring, … and a high-speed data sequencer for control of stimulus and response patterns. Additionally, the Astronics PXIe-6943 operates at data rates up to 50 MHz with 1 ns edge placement, variable slew rates, and a <3 ns channel-to-channel skew. It also supports synchronized digital test systems from 32 to 224 channels.
-
product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Digital Synchro and Digital to Resolver
DSN-DRN
Computer Conversions Corporation
The DSN - DRN Series are highly reliable, miniature, narrow profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
product
PXI Dual RF Attenuator, 2.3GHz
41-181-022
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
product
Digital Multimeter, 5.5 Digit, OLED Display
34450A
Turbo charge your production line with the Keysight 34450A 5.5-digit multimeter with OLED display. With its fast speed of up to 190 readings per second, you can increase your manufacturing throughput tremendously. Get highly accurate, repeatable, and trustworthy measurements with 0.015% DCV accuracy designed to meet general industrial and educational needs.
-
product
PXI Switchable-Input Programmable Step Attenuator Module, DC to 50 GHz
M9169E
The M9169E is a 3-port PXI programmable step attenuator module with a switchable path for a calibrator signal (cal input) into the input of a signal analyzer to improve amplitude accuracy. The M9169E has 0.03 dB insertion loss repeatability throughout the operating life of up to 5 million cycles per section. Its excellent attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 180 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.827-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXIe-6569, PXI FlexRIO Digital I/O Module
787281-01
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
product
Handheld Digital Multimeter, 3 ½ Digit, Basic
U1231A
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode and continuity visual/audio alerts. Keysight Remote Link Solution enabled.
-
product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s, 500 MHz Bandwidth
DN2.221-04
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
PXI FlexRay Digitizer
PXD7113
Digitize high resolution waveforms with the fully isolated PXD series Digitizers. Minimize interference and measure "in-circuit". Measurement errors are reduced by a high input impedance.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4I.4481-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785959-01
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
16-Bit Digitizer
PA72D16180A
The PA72D16180A is a 16-bit digitizer, capable of capturing waveforms at speeds up to 180Msps. An onboard offset voltage source allows capturing offset signals while still using the optimal range for maximum ADC utilization. Two onboard filters allow suppression of out-of-band noise. The 64MWord onboard memory enables capturing very long waveforms, or sequentially capturing multiple signals with minimal intermediate bus communication.
-
product
PCI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated Digital I/O Device
778968-01
The PCI-6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
USB Modular Digital Multimeter, 5 digit
U2741A
The Keysight U2741A USB Modular Digital Multimeter provides a broad range of measurement functions, including temperature and frequency. The U2741A is a 5.5-digit resolution digital multimeter that is able to capture up to 100 readings/sec. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
product
96-Channel Digital I/O Plug-In
1260-114
The high channel count of the digital I/O plug-ins allows a significant portion of digital I/O to be realized in a single slot of the Adapt-a-Switch™ carrier, saving valuable VXIbus chassis space. The 1260- 114 provides 96 digital I/O channels in twelve groups of eight bits each.
-
product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
product
PXI/PXIe High-Accuracy Multi-Measurement Device
PXM(e)7822
The PXM Multi-Measurement Devices combine the functionalities of a 16 Bit digitizer, a 24 Bit multimeter, a timer/counter and a highly flexible trigger matrix in a PXI or PXIe device.
-
product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2233-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
NI-9436 , 120 VDC to 240 VDC/120 VAC to 240 VAC, 8 Channel (Sinking/Sourcing Input), 20 ms C Series Digital Module
784338-01
120 VDC to 240 VDC/120 VAC to 240 VAC, 8 Channel (Sinking/Sourcing Input), 20 ms C Series Digital Module - The NI‑9436 works with industrial, high-voltage logic levels and signals to connect directly to a wide array of industrial devices such as fans and motors. Each channel accepts signals from 120 VDC to 240 VDC and 120 VAC to 240 VAC; features transient overvoltage protection between the input channels and earth ground; channel to channel and channel to earth isolation up to 250 Vrms; and has an LED that indicates the status of each channel.





























