-
Product
Serial Analyzers
-
This product enables passive monitoring, debugging, and target system analysis of all speeds of Serial RapidIO Gen2 and Gen1 from the physical coding-sublayer (PCS), through serial protocol, to full-duplex link protocol exchanges. Stimulus transmitters allow for injection of SRIO packets, control symbols, and 8b/10b characters.
-
Product
JTAG Boundary-Scan Hardware
-
JTAG Boundary-Scan Hardware by Corelis, including boundary-scan controllers, 12C serial bus protocol analyzers & exercisers, JTAG boundary Scan Modules, high-volume production JTAG systems, 7 support for 3rd party JTAG controllers
-
Product
PICkit Serial Analyzer
DV164122
-
The PICkit Serial Analyzer is a low-cost USB-based tool used to direct communication between a PC and an external serial device. I2C™ - Master, I2C™ - Slave, SPI - Master, USART – Asynchronous, USART – Synchronous, LIN (external hardware required to meet electrical specifications), MICROWIRE.
-
Product
Serial analyzer
-
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
Product
Smart Protocol Analyzer
-
Works transparently over the Computer's I/O ports (serial & network). The analyzer supports Modbus, Fisher-ROC, BSAP, DNP and other Protocols. In addition to monitoring, this tool is capable of simulating Master and Slave devices.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
Fifo Serial Analyzer
FSA32
-
FSA32 is a Windows based protocol analyzer for debugging serial asynchronous communication. FSA32 uses the standard COM ports of a PC and does not require any other hardware except for the physical connection to the line.
-
Product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
-
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
Product
In-Circuit Emulator
DS-51
-
* Real-Time and Transparent In-Circuit Emulator * Supports Most of the 8051 Derivatives * Emulates 1.5V to 6V Microcontrollers * Maximum Frequency of 42MHz * 64K/512K of Internal Memory with Banking Support * 32K Trace Memory "on the Fly" * 64K Hardware and Conditional Breakpoints * MS-Windows and Keil ?Vision Debuggers * Source-Level Debugger for Assembler, PLM and C * On-Line Assembler and Disassembler * Performance Analyzer * Serially linked to IBM PC at 115 Kbaud
-
Product
Data Analyzer, 16 GHz Bandwidth, 4 Input Channels, 80 GS/s Max Sample Rate
SDA 816Zi-B
Analyzer
16 GHz, 80 GS/s, 128 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display. 50 ohm and 1 Mohm Input, 6.5 Gb/s Serial Trigger, 8b/10b and 64b/66b decode. Also operates in 4ch, 40 GS/s, 64 Mpts/Ch mode.
-
Product
Fifo Serial Analyzer Breakout Box
FLLBOB
-
FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.
-
Product
Fifo Serial Analyzer for DOS
FLL
-
FLL is a DOS based protocol analyzer for debugging serial asynchronous communication. FLL uses the standard COM1 and COM2 ports of a PC and does not require any other hardware except for the physical connection to the line.
-
Product
Data Analyzer, 6 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
SDA 806Zi-B
Analyzer
6 GHz, 40 GS/s, 4ch, 64 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display. 50 ohm and 1 Mohm Input, 6.5 Gb/s Serial Trigger, 8b/10b and 64b/66b decode.
-
Product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
-
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
Product
Data Analyzer, 8 GHz Bandwidth, 4 Input Channels, 32 GS/s Max Sample Rate
SDA 808Zi-B
Analyzer
8 GHz, 32 GS/s, 4ch, 32 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display.
-
Product
Fifo Serial Analyzer 2 TO 2 Breakout Box
FLL222
-
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-44
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
Serial Interface
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
9-Pin DB-9 Female to 9-Pin DB-9 Female Serial Cable
182238-02
Serial Cable
RS232 Null-Modem Cable, DB-9 Female to DB-9 Female, 2m
-
Product
Enhanced Serial Interface Module for Excalibur 8000 Family of Carrier Boards, with High Baud Rate & High Throughput
M8KSerial
Serial Interface
The M8KSerial is an enhanced serial interface module for the multiprotocol Excalibur 8000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to two independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M8KSerial module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 8000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M8KSerial module is supplied with C drivers, including source code.
-
Product
PXI-8430, 4-Port, RS232 PXI Serial Interface Module
778983-01
Serial Interface
4-Port, RS232 PXI Serial Interface Module - The PXI‑8430/4 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB-232/4, 4-Port, USB, RS232 Serial Interface Device
778473-04
Serial Interface
The USB‑232/4 interface transforms your USB port into a single asynchronous serial port for communication with RS232 devices. You can use a USB‑232/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCIe-8432, PCI Express, 2-Port, Isolated, RS232 Serial Interface Device
781744-01
Serial Interface
The PCIe‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial … interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
10-Pin RJ50 Male to 9-Pin D-SUB Male Serial Cable
182845-03
Serial Cable
S8 Serial Cable, 10Pos Modular Plug to DB-9, 3 m (non isolated)
-
Product
Envision Analyzer & Generator
MIPI C-PHY/D-PHY
Analyzer
The Envision X14 Analyzer capture utility provides deep analysis for MIPI camera and display protocols over C-PHY and D-PHY layers. The X14 Analyzer can be positioned either as an endpoint to test a CSI-2 or DSI-2 stream or tapped in between a CSI-2 or DSI-2 device and host for passive monitoring and analysis. The Envision X14 ensures fast Time-to-Insight through its rich set of innovative features for debug analysis and identifying and resolving elusive protocol errors.
-
Product
Boundary-Scan Interactive Analyzer & Toolkit
ScanExpress JTAG Debugger
Analyzer
Test probe access is a luxury—modern electronic system design techniques such as blind and buried vias or ball-grid-array (BGA) devices guarantee limited signal access. Test points quickly reduce precious board real-estate and can even degrade performance. ScanExpress JTAG Debugger overcomes these limitations to provide the control and visibility necessary to quickly debug and test hardware, using a simple JTAG port to interface with IEEE-1149.1 compliant devices.Whether debugging prototype hardware, enhancing production tests with boundary-scan control, or diagnosing a faulty board in the field, ScanExpress Debugger’s easy-to-use and versatile interface helps engineers test and debug systems faster and more efficiently.
-
Product
PXIe-8431, 8-Port, RS485/RS422 PXI Serial Interface Module
781473-01
Serial Interface
The PXIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Splitter Drive Cable, 2 Meter
85555A
Serial Cable
This cable is used to connect the 85523A/B CalPod controller to the 85556A CalPod control cable splitter. If longer distances are required, use the 85554A 10 meter drive cable extension. This cable is supplied with the 85556A CalPod control cable splitter.
-
Product
PXIe-6594, FlexRIO High-speed Serial Module (28 Gbps), KU15P
786939-01
Serial Interface
PXIe, 28 Gbps, 8-Channel PXI High-Speed Serial Instrument. - The PXIe-6594 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale+ FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe-6594 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
Serial Interface Device
Serial Interface
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
