Noise Figure
delta of UUT noise to ideal.
-
Product
Noise Monitoring System
NoiseTutor
-
Continuous monitoring of environmental data in remote areas has always presented a unique set of challenges. Typical solutions involve complex installations, frequent visits to remote locations to keep the system fully operational and require expert level attention to retrieve and share data amongst customers, consultants and project leads.
-
Product
Components - Low Noise Amplifiers (FLNA)
FLNA series
-
Farran's FLNA series low noise amplifiers are constructed with discrete or MMIC pHEMT devices that operate over the frequency range 18 to 110 GHz. These amplifiers are specifically designed for low noise applications.The amplifiers are offered in two categories: standard and custom-built. The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Phase Noise Measurement Up To 70 GHz
S930317B
-
S930317B enables phase noise measurements using a PNA or PNA-X vector network analyzer. Simplify your measurement workflow by measuring phase noise on the same connection as your network analysis measurement of 2-port active devices up to 70 GHz, without needing to connect a spectrum analyzer or harmonic mixer.
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Particle Impact Noise Detection
BW-LPD-DAQ4000
-
Computer based controller with predefined MIL-STD test sequences stored (New)Create unlimited custom tests with multiple vibration frequencies and acceleration and other parameters to meet unique requirements (New)
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Phase Noise Tester 5MHz to 40GHz
Model 7340
-
Berkeley Nucleonics Corporation
Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
Coaxial Cable
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
Product
Noise Meters
-
Here you will find a full range with an industrial standard noise meter / sound meter to suit every requirement. With the portable noise meter you can carry out measurements quickly to gain control of a situation or to set the sound meter to take timed measurements. The noise meter is important for all industries, especially by using it as a mobile noise meter which is able to assess office stress levels or street noise levels. Often problems arise from noisy neighbors or if bars and restaurants are in residential areas and produce noise levels after 10 pm in excess of what local laws permit. A noise meter / sound meter will help here.We can assess which noise meter or sound meter you require in relation to the issue you have and the relating laws (requirements regarding a sound meter and a sound meter’s usage vary depending on the country). We also have noise meter microphone extension cords, tripods, sound meter calibrators and calibration certificates for most noise meter models.
-
Product
Playback And Noise Simulation
-
Our systems make sounds and vibrations perceptible – from the pure, aurally accurate playback of binaural recordings to the realistic reconstruction of sound fields and background noise.
-
Product
Multi-Channel Automotive Noise Finder
7633A
-
Peaceful Thriving Enterprise Co Ltd
Multi-Channel automotive noise finder is a portable equipment to diagnose the defect of the vehicle. When the generator is running, it can detect the impact and vibration due to the defect and failure of bearing, gear, valve, crank, cylinder, gear box, and vehicle body…etc. With this equipment, the repairer can clearly locate which part of the machine cause the noise and how serious is it; even though the repairer operates the equipment in a very noisy environment.
-
Product
The All-In-One Noise Test System
NXA Series
-
Noise eXtended Technologies S.A.S.
The NXA is a fully automated Phase Noise analyzer. Its dual channel architecture allows the system to use a cross-correlation process to cancel its internal noise floor. This reliable technique provides access to the unique noise floor performance of the DCNTS.
-
Product
Noise Monitoring System
Harmony
-
A system that consists of automatic noise measuring device, transmission device, computer system, and operation analysis software, and provides accurate data necessary for establishing noise-related policiesby providing real-time information such as noise level, location, and device status for each branch.
-
Product
Carrier to Noise Generators
CNG-DX
-
Hollis Electronics Company LLC
CNG-DX provides improved noise generation with its internal digital power meter and built-in noise generator. This single instrument provides accurate and repetitive carrier-to-noise setting ability in one box. The CNG-DX is an ideal instrument for creating realistic scenarios for closed loop testing of satellites, ground equipment and mobile transceivers.
-
Product
Phase Noise Measurement Up To 125 GHz
S930321B
-
S930321B enables phase noise measurements using a PNA or PNA-X vector network analyzer. Simplify your measurement workflow by measuring phase noise on the same connection as your network analysis measurement of 2-port active devices up to 125 GHz, without needing to connect a spectrum analyzer or harmonic mixer.
-
Product
Low Noise Prepolarized Microphone
378A04
-
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
Product
SCB-100A Noise Rejecting, Shielded I/O Connector Block
785024-01
Terminal Block
100-Pin Female SCSI to 100-Pin Female Screw Terminal, DIN Rail, Wall, Pane Terminal. Block The SCB-100A is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with shielded cables, the SCB-100A provides rugged and protected signal connectivity. It has a mechanical enclosure that features a magnetic removable lid and pinout diagrams. It also includes pane, wall, and DIN Rail mount options.
-
Product
Ultra Low Noise Disciplined Frequency 4220a Standard with Rubidium and OCXO Clean-Up Oscillator
-
Precise Time and Frequency, Inc.
The ptf 4220A is an Ultra Low Noise Disciplined Frequency Standard with rubidium and OCXO clean-up oscillator.The instrument contains a high performance rubidium module, with an extended life design, and very low aging rate, with high quality OCXO o/p for low phase noise.
-
Product
Low Noise Pre-Amplifiers
-
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
Product
Noise Dosimeters
-
High performance instrument: Spectrum Analyser, Memory and USB port. Ideal for the measurement of noise according to OSHA, MSHA, NIOSH, ACGIH, DoD, etc.
-
Product
High Density, Low Noise, Floating Low Voltage Power Supply System
PL500 Series
-
The WIENER PL500 is a high density, low noise, floating low voltage power supply system. The PL500-Series has been designed to power lowest noise electronics with medium to high currents (10A to 500A current/channel range) over long distances in voltage or current controlled mode. Operating in either un-sensed or sensed mode the dynamic behavior can be set internally or by software for short, medium or long distances.
-
Product
Phase Noise Testers / Signal Source Analyzers
7000 Series
-
Berkeley Nucleonics Corporation
The 7000 series is an all-in-one integrated solution that offers an indispensable set of low-noise phase measurement functions. Offering both Absolute and Additive(residual) measurement capabilities in one unit at no additional cost, the 7000 series is the most flexible solution on the market. The instrument comprises a two-channel, cross-correlation system with two internal, tunable references sources that also allows measurements with externally sourced references. We offer three platform options for the 7000 Series Phase Noise Testers: the 7070 1 MHz to 7 GHz, the 7300 1 MHz to 26 GHz, 7340 1 MHz to 40 GHz, 7350 1 MHz to 50 GHz, and the 7360 1 MHz to 65 GHz.
-
Product
Sound Level Meter for Automotive – Car Noise Emission Inspection
HD2010MCTC
-
The level of noise produced by vehicles shall comply with standards prescribed by international regulations. During car inspections, horns and exhaust devices must be in good condition and comply with the requirements.
-
Product
Pass-by Noise System
-
Vehicle Pass-by Noise TestingA very flexible Pass-by noise test system for characterizing the overall acoustic signature of any vehicle. Our solution brings a simpler, more effective and cheaper way to obtain accurate velocity and acceleration results for the Pass-by Noise test.
-
Product
Low Noise High Precision High Voltage Amplifier
WMA-280
-
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
Product
Portable 4-channel Noise & Vibration Analysis System
WCAmini AD-3661
-
* USB bus power unit * 24 bit, 4-channel measurement * A channel exclusively for tacho pulse measurements * WCAPRO (multi analysis software) * FFT analysis and real-time octave analysis * Tracking analysis and throughput recording/playback * Equipped with WCA Lite (easy-to-use analysis software)
-
Product
Noise And Vibration Tester
-
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
Product
Low Noise Voltage Preamplifier
1201
-
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
-
Product
Noise Legislation Assessment Kit - Sound Meter And Dosemeter
05NK006
-
This system provides you with everything you need for noise risk assessments for noise legislation in one small package. A sound meter, dosemeter and calibrator kit featuring projected daily noise exposure from one short measurement and true peak for monitoring peak action levels.
