Automotive
Car industry or about cars.
See Also: Vehicle, V2X, Truck, Electric Vehicle, Car, Autonomous Vehicle, Autonomous Underwater Vehicle
-
Product
Environmental Test Chambers
TTC/CTC
-
Rapid, precise and energy-saving temperature changes in the range from -42 C to +190 C, along with fast humidity recovery times, make the TTC temperature test chamber and the CTC climatic test chamber with humidity unit a perfect duo for controlled material testing, function tests, ageing tests or climate tests on composites, concrete, plastics or electronic components in material technology, the automotive and aerospace industries, and electronics.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 750 V Isolation
43-752A-001
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
AstroAI Digital Multimeter
-
Check out our VIDEO on the left side and take a quick tour of AstroAI Multimeter! ACCURATELY MEASURES: Voltage, DC current, resistance, diode, continuity and moreTROUBLESHOOTS: Automotive and household electrical problems safely and accurately
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
-
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
High Current Generators
-
Quantum Composers is a recognized industry leader for Current Pulsers and Firesets. We specifically design our units for use in pyrotechnic applications such as Aerospace, Defense, Propulsion, and Automotive Safety and Squib testing. Our current generators are used throughout the world in demanding and harsh testing environments where quality, reliability, and safety are paramount. We are also an excellent replacement and upgrade solution for legacy equipment.
-
Product
Dynamometer
-
Innco Systems EMC Chassis Dynamometer Systems (sometimes referred to as a ‘’rolling road’’), used in the development and homologation for Automotive Industry, are specifically designed to be used in Anechoic Chambers.
-
Product
PXI 34-Channel 4-Bus 2A Fault Insertion Switch
40-197A-001
-
This 34-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers. A low cost 16-channel option is also available.
-
Product
Functional Test Fixtures
-
Intrinsic Quality delivers turnkey standalone Functional Test fixtures and Windows based functional testers that are custom engineered with innovation and reliability to meet your testing needs. Our experience and expertise ensure a production ready functional test solution that is cost-effective, on time and on budget. Our broad range of test solutions includes simple continuity testers to complex microcontroller assembly testers. Our customers include military, aerospace, automotive, medical and consumer OEMs. We serve the needs of low volume high mix CEMs and off shore high volume manufacturers.
-
Product
Sub-systems
-
Our self-contained, in-house components design and fabrication capacities ensure the breadth of sub-assemblies offered from rapid prototyping and proof of concept to full production. Ducommun has produced many high performance millimeterwave band sub-assemblies for commercial and military system applications. Among them, the K and Ka band directional Doppler Radar front ends are in production. Several hundreds of sets have been delivered. In addition, Ducommun has delivered Ka through W band engineering prototypes for plasma detection system, automotive Radar, speed Radar, automatic test set, radio telescope, missile terminal guidance, telecommunication system etc. applications.
-
Product
Automotive Contactor
Pad Series
-
Johnstech International Corporation
Automotive Contactor is just the product you’re looking for! This Xtreme Temperature (XT™) capable product is designed to maximize your test results, regardless of your tri-temp testing objectives! Even if you are not testing outside the temperature limits of standard Contactors and sockets, the robust design of the XT™ Contactor provides additional design margin and certainly satisfies even your roadmap requirements.
-
Product
Transmission Meters
-
Shenzhen Linshang Technology Co., Ltd.
As a leading window film transmission meter (window tint meter) manufacturer, Linshang Technology provides a variety of window film meters to measure transmission rate, rejection rate, SHGC for materials such as automotive film, thermal insulation film, architectural film, thermal insulation glass, etc. There are mainly portable solar film transmission meters LS160 series, LS162 series, LS163 series, desktop demonstration window tint meters LS101, LS180, LS181, L182, split transmission meters LS110A, LS110H. Whether you want to measure UV or IR rejection (940nm, 1400nm) or visible light transmittance, you can find a suitable window film meter here.
-
Product
DC Power Supply With Scope, Arbitrary Waveform Generator, And Automotive Application Features Bundle
E36154AGVX
-
The Keysight E36154AGVX consists of a Keysight E36154A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36154A includes single-output and auto-range capabilities, 30V, 80 A, 800 W, and LAN and USB interfaces.
-
Product
PXI Automotive Ethernet Interface Module
-
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
Product
Industrial Power Supply
-
Mornsun Guangzhou Science & Technology
Mornsun offers one-stop solutions of power supplies for all types of applications: railway, automotive, photovoltaic, smart grid, medical, mining, etc.
-
Product
Universal Test Machines - Up to 150 kN
LD Series
-
Universal testing machines for testing applications such as plastic, rubber, wood, packaging, construction materials, metals and automotive parts. The powerful LD Series testing machines from Lloyd Instruments combine high performance, ease of use and superior flexibility. These universal materials testing machines are ideal for testing applications up to 100 kN (22480 lbf) and are designed for both routine quality control testing, automated testing and for performing complex multi-stage testing.
-
Product
Cable, 3POS B2CF Omnimate To Pigtail, Automotive Ethernet, Unshielded, 5m
787108-05
-
3-Pin, Male B2CF Omnimate to Pigtail, Automotive Ethernet Cable - The B2CF3M-Pigtail Automotive Ethernet Cable helps you connect Automotive Ethernet interfaces with ECUs, devices, switches, and accessories. This cable is available in 1 m and 5 m lengths.
-
Product
Multi-Output Driver ICs
-
Housing multiple half-bridges and high-side switches on a single IC, our multi-output driver ICs are designed to drive small automotive loads and medium current DC motors as well as providing protected supply lines.
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
Electric Fatigue Testing Machine
EFT Series
-
Jinan Testing Equipment IE Corporation
EFT series electric fatigue testing machine is an ideal platform to test a variety of materials and components for the following high demanding tests: Quasi-static test; Reverse-stress mechanical low cycle fatigue loading tests (LCF); High temperature creep, stress-rupture, relaxation tests in load/strain control mode for medium-term or long term period. Mechanical fracture tests like crack growth & toughness tensile/compression test for ceramics in both room- or vacuum-, high- temperatures up to 1200 C conditions etc. Compression test on plate springs or clutch springs etc. It is also widely used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastrometric materials, etc. It adopts electric actuator structure with all-elastic, backlash free, central ball-lead screw driving to achieve direct force transmission to the specimen, it is especially a perfect choice for R&D institutes, universities, nuclear power, automotive and aviation, & aerospace sectors from metals, composites, ceramics, springs and component parts.
-
Product
Automotive Testing
-
Unique E-Marking Service: Efficient, Flexible and Quality Kiwa Dare is a full compliant test house that perform tests and measurements for customers so that the E-Marking (type approval) can be obtained on vehicles or automotive products and components.
-
Product
End of Line Test System for Automotive Seats
AS519
-
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
Product
Tracer Gas Leak Testers
-
At ATEQ, we understand how essential it is to detect hydrogen leaks as swiftly as possible. For this reason, we carry our own high-quality gas tracer equipment. One of popular tools is the H 6000, which is a multipurpose, handheld hydrogen leak detector designed to identify a broad spectrum of hydrogen gas concentrations. You can use this instrument for multiple applications like automotive and HVAC.
-
Product
Tension Meters
-
Guangzhou Amittari Instruments Co.Ltd
The Belt Tension Meter Mainly use for automotive belt tension measurement, also can measure and adjust ribbon, filamentous, linear, reticular and other wide objects tension. Applicable to the automotive, textiles, wire and cable, metal wire, plastic film, paper, printing, film industries etc.
-
Product
Radio / Conformity Tests
-
The safe and effective use of radio frequencies (HF), referred to in English as radio frequencies (RF), must be checked for every device with integrated radio technology. The legal requirements for radio frequency (HF) tests vary depending on the use of the device (medical devices, automotive and telematics devices, cellular devices, etc.).
-
Product
Programmable DC Electronic Loads
SDL1000X/X-E Series
-
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
43-752A-901
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781116-01
-
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
-
Product
Capacitors - Aluminum Electrolytic
-
Aluminum Electrolytic Capacitors provide a smaller capacitor option when high power ratings and high capacitance values are needed. Vishay offers a broad choice of aluminum capacitors, as well as the product support necessary to specify the ideal products for automotive, medical, alternative energy, and other high-demand applications.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
-
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Automotive Diagnostic Scope
ATS610004D-XMSG
-
Automotive oscilloscope with 4 differential channels, 1GS/s, 250MHz BW, 12/14/16 bit, integrated SureConnect connection test, SafeGround single-ended connection option on each channel, and up to 257 MSamples memory per channel.
