-
Product
Laboratory EM current meter / water level and wave height meter
-
ACM2-RS and ACM3-RS are 2-D and 3-D electro-magnetic current meters for laboratory experiments. The models provide digital output, a high-speed sampling rate and insusceptibility to electro-magnetic noise. ACH-600RS is a highly sensitive capacitance water level meters. With the new system, a maximum of four different sensors can be connected to the compact interface unit, enabling simultaneous recording on a personal computer. Additionally, the system can provide analog output as well as necessary. While conventional water level and wave height meters cannot be used near velocity sensors, our instrument can be as near as 5 cm without increasing noise, due to its special isolated circuit. The result is an innovative system that is capable of achieving highly accurate data.
-
Product
Phasing Voltmeter/Sensor (2 in 1)
-
STB Electrical Test Equipment, Inc
STB unit replaces 3 separate units manufactured by competitors - line phasing, capacitance phasing and line to ground Versatile, lightweight and easy to useEach portable meter has a single rangeMeter usage: Voltage detection and phasing at capacitance test points or voltage detection and phasing on bare energized conductors (overhead & underground)Probes can be separated to be used as a voltage sensor or capacitance sensorFive position selector.
-
Product
Capacitive to Digital and Touch Screen Controllers
-
Are 12-bit successive approximation analog-to-digital converters (SAR ADCs) with a synchronous serial interface and low on-resistance switches for driving 4-wire resistive touch screens.
-
Product
Analogue (1kV below) Insulation Tester
4132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
Product
Mixed Signal Oscilloscope - 500 MHz, 4 Analog Plus 16 Digital Channels
MSOX3054T
Oscilloscope
500 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
-
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
Product
8 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Oscilloscope
WavePro 804HD
Oscilloscope
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s. Up to 5 Gpts of acquisition memory enables detailed viewing of long events. 15.6" 1900 x 1080 Full HD capacitive touchscreen. New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector. MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
Product
In-circuit Test
i3070
-
The Keysight i3070 In-Circuit Test (ICT) System embodies proven technology, enhancing test efficiency through time-tested software, hardware, and programmability. Catering to diverse PCBA sizes, it addresses applications such as IoT, 5G, automotive, and energy. Its unique design minimizes undesired effects from parasitic capacitance, enhances immunity to crosstalk, and eliminates stray signal coupling, ensuring consistent and repeatable measurements.
-
Product
Testing Services
-
*Programmable Multipoint Tester*Over 8,000 programmable test points (DWV, Capacitance, Insulation Res., 2/4-Wire Resistance, etc.)*1500VDC / 1000 VAC Dielectric Withstanding Voltage (DWV)/ Hi-Pot (Programmable Dwell times)*Full Electronics laboratory complete with state of the art testing equipment*Custom Unit Testing (Designing of Specialized Test fixtures)*EMI Testing*Temperature and Humidity Testing*Shock Testing*Vibration Testing*Sand and Dust / Altitude Testing*Military Qualification Tests Performed
-
Product
4 Channel Oscilloscope
2567B-MSO
-
The 2560B Digital Storage (DSO) and Mixed Signal Oscilloscope (MSO) Series offers 100 MHz, 200 MHz and 350 MHz bandwidth models in a 4-channel configuration, with a sample rate of 2 GSa/s and a maximum memory depth of 200 Mpts. Additionally, these oscilloscopes are equipped with a large 10.1" capacitive touch display that provide 1024 x 600 resolution and intuitive touchscreen gestures.
-
Product
Analytical Services
-
Atomic Force Microscopy (AFM) allows for sub nanometer resolution imaging of surface topography and is able to quantify surface roughness at the angstrom scale. Our team can give you highly accurate measurements such as surface topography, dopant distribution, magnetic domain features, and a wide variety of other sample properties to give you the information you need to do great work.Park can provide measurements in the following areas:● Topography (surface roughness, grain size, step height, etc.)● Mechanical Properties (stiffness, etc.)● Electrical properties (capacitance, conductivity, etc.)● Thermal properties ● Magnetic properties These properties can be measured in air or liquid, depending on your needs.
-
Product
On-Line Moisture Meters
-
Many methods are available for measuring moisture content on line, in real time: NIR, RF Capacitance, NMR (Nuclear Magnetic Resonance), and Microwave, among others. Finna Sensors is unique in that it has experience with most of these methods and is therefore able to recommend the best possible solution for any application.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 8 GHz, 4 Analog Channels
DSOS804A
Oscilloscope
8 GHz bandwidth4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
Oscilloscope - 200 MHz, 4 Analog Channels
DSOX4024A
Oscilloscope
200 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary WaveGen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Pressure Sensors
ESCP-MIS1 Sensor
-
ES Systems has developed a series of medium isolated pressure sensors suitable for applications with harsh environmental conditions where resistance to corrosive fluids or gases is required. Each sensor integrates a MEMS capacitive pressure sensor die, and a CMOS ASIC for the signal conditioning. The MEMS pressure sensor dies are underpinned by ES’s innovative microfabrication process for silicon capacitive sensors.
-
Product
DC Hipot and Megohmmeter
PTS Series
-
The PTS Series can perform high voltage DC hipot/proof and current leakage testing as well as resistance measurement testing. Most models offer a high output current for quicker charging of capacitive loads like cables. Like all HVI portable test equipment, the PTS Series is designed to withstand the rigors of field use.
-
Product
Software
Dielectric Constant
-
Materials Development Corporation
The Dielectric Constant option allows the user to measure the dielectric constant of a wide range of materials. Simply input a test voltage (in accumulation), the area (or diameter), and stray capacitance to determine the relative dielectric constant.
-
Product
Benchtop Multimeters
-
Precision Mastech Enterprises Co.
High-precision, AC-powered laboratory instruments designed for stationary use on workbenches to measure electrical properties like voltage, current, resistance, and capacitance.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
Programmable Capacitance Decade Box
PCS Series
-
A broad range of laboratory grade programmable capacitance decade boxes for applications requiring a programmable impedance unit controlled manually and by a computer via an IEEE-488, RS-232 interface.
-
Product
Capacitive Electromagnetic Flow Sensor
WFC
-
This is a flow sensor with a through structure.No foreign matter is clogged or detection failure occurs. Ideal for spot welding machines, various machine tools, induction hardening equipment, etc.
-
Product
Digital Multimeter
DMT-4010RMS
-
Monacor International GmbH & Co.
*True RMS measurement method*Dust and water protection according to IP class 67 with covered measuring sockets*Auto ranging for faster measurements*4000 digit resolution*Additional bar display*Voltage measurement up to DC/˜ 1000 V*Current measurement up to DC/˜ 10 A*Frequency measurement up to 10 MHz*Resistance measurement up to 40 MΩ*Capacitance measurement up to 40 mF*Temperature measurement -20 °C to +760 °C*Acoustic continuity test*diode test*Data hold (measured value memory)*peak hold*Maximum and minimum value recording*LC display with switchable background lighting*Automatic shutdown*overload protection*Supplied with test leads and protective case
-
Product
Infiniium S-Series High-Definition Oscilloscope: 500 MHz, 4 Analog Channels
DSOS054A
Oscilloscope
500 MHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s maximum sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 8.1 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and standard solid state drive for fast boot and high reliability Access a wide range of protocol, compliance, and analysis software
-
Product
Atlas ESR PLUS - Equivalent Series Resistance Meter
ESR70
-
The Atlas ESR provides instant measurement of a capacitor's ESR and it's capacitance value. Using the supplied gold plated probes (removable), the Atlas ESR can measure ESR down to a resolution of 0.01 ohms, up to 40 ohms. It can even measure ESR for capacitors that are in-circuit. Measurements are made at the industry standard frequency of 100kHz. Probes are now removable, allowing 2mm compatible probes to be fitted. Audible alerts are produced for various ESR levels allowing you to perform many tests in succession without having to look at the display.
-
Product
InfiniiMax Probe, 1.5 GHz
1130B
Oscilloscope Probe
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX3032T
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Clamp Meters
-
Basic functions:AC current: 40/400/1000ADC current: 40/400/1000AAC voltage: 4/40/400/750VDC voltage: 400mV/4/40/400/1000VResistor: 400/4/40/400K/4/40MTemperature: -20 to +750°CFrequency: 10/100/1000Hz/10/100kHz/10MHzDuty cycle: 0.1 to 99.9%Capacitance: 5nF/50nF/500nF/5μF/50μF/200μFSpecial functions:Auto rangingNCVDiodeContinuity buzzerLow battery displayData holdRelative data holdAuto/manual range shiftZeroAuto power-offOverload protectionSampling frequency: 3 times/sMaximum display: 3999Maximum open distance of clamp mouth: 55mmGeneral characteristics:Color: iron gray and orangeNet weight: approximately 274gLCD size: 46 x 32mmSize: 245 x 90 x 33mmPower: 1 x 9V and 6F22Packing content:CartonHandheld bagEnglish manualTesting leadBatteryTemperature probe
-
Product
AC Load Bank (Resistive/Capacitive)
K-1000 Resistive/Capacitive
-
Kongter Test & Measurement Co., Limited
A RCD (resistive/capacitive) generator load bank is non-linear load bank. The electronic and non-linear loads simulated by capacitive load banks are typical of the Telecommunications, Computer or Uninterruptible Power Supply (UPS) Industries.
-
Product
DC Pulse Current Capacitor
-
Both series can be customized as Low Voltage High Capacitance High Current Capacitors.We can customize Snubber Capacitor as Box type and support other parameters.For 250Vac~900Vac / 400Vdc~1,350Vdc and with higher Current requirement, please refer to our AC/DC Power Capacitors.Different applications can have very different capacitor electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
Product
Pre-configured Power Device Analyzer / Curve Tracer (B1505A with modules and fixture)
B1505AP
-
B1505AP provides eight different pre-configured packages that satisfy a wide variety of power device measurement requirements. The package can be selected according to voltage / current range and the requirement for capacitance measurement.
