PCI Backplanes
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 3.55kΩ
50-297-023
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express VXIbus Slot-0 Interface
ProDAQ 3030
-
The ProDAQ 3030 PCI Express VXIbus slot-0 interface is a C-size, register-based VXIbus module providing a direct connection from a PC to a VXIbus mainframe using the high-speed PCI Express serial bus. Together with any of the available host cards, the ProDAQ 3030 enables users to use a laptop, desktop, or server computer as an embedded controller. Optimized for low latency and high throughput, it provides a high-performance but cost-effective solution for a data acquisition system.
-
Product
PCI 50xDPST Reed Relay Card
50-115A-122
Reed Relay
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI Direct Digital Synthesizers
SYNTH300 SERIES
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.Software support for Windows Vista, Windows XP,Linux and Labview source code availableFor detailed specifications, please refer to the Synth300_Manual
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
Product
34 lane, 34 port, PCI Express
PEX88032
-
The new PEX88000 PCIe Gen 4.0 product family of switches builds on the longevity of the PEX series of switches, now spanning 12 families. The PEX88032 switch allows Data Center and Cloud Providers to build flexible, scalable rack infrastructures, along with other advantages.
-
Product
6-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB210
-
*Designed for PICMG 1.3 SBC*Compatible with AX61222TP/AX61220TP chassis*Supports one PICMG 1.3 CPU card slot, two PCI slots, two PCIe x1 slots, and one PCIe x16 slot
-
Product
PCI Multifunction Board
PCI-1602F/8K/S
-
The PCI-1602/1602F series is a family of high performance and high resolution data acquisition boards for the PCI bus. It features a continuous, 100KHz for PCI-1602 (200KHz for PCI-1602F), gap-free data acquisition under DOS and Windows. The PCI-1602 family has the same hardware architecture as PCI-1802L. The PCI-1602 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1602 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
CompactPCI Serial 3U Backplanes / Power connector
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to the PICMG CPCI S.0 CompactPCI Serial specification. This backplane features 1 power slot in addition to either 6 or 9 cPCI serial slots.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Interface Card
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
PCI Daughter Boards
DB-8225/2/DIN (with DIN-Rail mounting kit)
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
PCI Multifunction Board
PCI-1802H
-
The PCI-1800 series is a family of high performance data acquisition boards for PCs with a PCI bus. It features a continuous, 330KHz for low gain (44KHz for high gain), gap-free data acquisition under DOS and Windows. The PCI-1800 family has the same architecture and has two 12-bit D/A output channels, 16 digital input channels, and 16 digital output channels. The PCI-1800H, PCI-1800L provides 16 single-ended or 8 differential inputs. The PCI-1802H and PCI-1802L provide 32 single-ended or 16 differential inputs. The -H means high gain model and the -L means low gain model. The scan function of PCI-1800 is so amazing. We call it Magic Scan. The variable channel scan function is found in some famous data acquisition boards. Compared to Variable channel scan, the Magic Scan improves a lot functions and meets the demand of high end users. The Magic Scan mechanism not only scans the different input channels at vastly different rates, but also at different gain. Even in multi-channel scans, the sampling rates can maintain at 330KS/s.
-
Product
49 lane, 13 port, PCI Express
PEX 9749
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
PCIe Clocks: Time Signal Receiver For The PCI Express Bus
-
Meinberg Funkuhren GmbH & Co. KG
Although the PCI Express bus is software-compatible with other PCI implementations, the hardware of these PCIe plug-in cards is based on a different concept.Fewer lines are used for data transmission than, for example, with PCI plug-in cards - a high transmission rate is achieved by using a fast serial protocol.
-
Product
ARINC PCI Express 4 Lane Interface Cards
PCIE4L-A429
Interface Card
Alta Data Technologies’ PCIE4L-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal. The 4 lane card (PCIE4L) is normal 1/2 height common for most desktop and larger server systems.
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCI
APXX3910
Simulator
STANAG3910/EFEX Test and Simulation module for PCI with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APXX3910 is a functional replacementfor model APX3910.
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
PCI Digital I/O and Relay Driver Cards
-
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 26.7kΩ
50-297-032
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 1.81kΩ
50-297-022
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card
50-298-031
Programmable Resistor Modules
The 50-298-031 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O Module
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
PCI Smart Bus Extenders
PCIEXT-64U - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
PCI General Purpose Relay Card, 26xSPDT, 2A
50-131A-002
-
The 50-131A-002 26xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
16 Channel ADC for PCI
PCI392
-
The PCI392 16-Channel Common-Mode Input ADC for PCI is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs all functionality like calibration. User-specific functions can be added for customized operation.
-
Product
PCI Data Acquisition Boards
AD14-100DMA Series - Dual 14-bit A/D, 25 MS/s
-
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
Product
PCI Daughter Boards
DB-16P
-
The DB-16P is a 16 channel isolated digital input daughter board for the A-82X board or any 812pg, 711 726, 720 series board, and PCI-Bus Multi-function boards. The optically isolated inputs of the DB-16P consist of a bi-directional OPTO-coupler with a resistor for current sensing. You can use the DB-16P to sense a DC signal from TTL levels up to 24V. You can also use the DB-16P to sense a wide range of AC signals. You can use the board to isolate the computer from large common-mode voltages, ground loops and voltage spikes that often occur in industrial environments.
-
Product
Backplane
-
Axiomtek offers various kinds of backplanes for industrial computing platforms, including PICMG 1.0 PCI, PICMG 1.0 ISA, PICMG 1.3 full-size, and PICMG 1.3 half-size backplane. Axiomtek's backplane product line provides not only the highest compatibility with power supply unit but also the best choice of slot expansion.
-
Product
PCI 4-Input Frame Grabber
611
-
Color or monochrome: PAL, SECAM, NTSC, RS-170 compatible 4 composite video inputs or 3 composite and one S-video 8 TTL I/O lines for camera control Programmable AGC, hue, contrast, saturation Optional enhanced SDK for Windows 98/2000/NT/XP/CE Optional Linux and QNX drivers
