SD Card
A non-volatile memory card format.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 62.1Ω
50-298-011
Programmable Resistor Modules
The 50-298-011 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 62.1Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
-
Product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
-
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
Product
Advanced Circuit Card Automated Test
ACCAT
-
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
Product
GPIB Controller Card
GPIB-cPCI-XL
GPIB Controller
The GPIB-cPCI-XL is a GPIB controller card for PXI and CompactPCI computers.
-
Product
8-Channel, 100 MHz Counter/Timer/Frequency Meter Function Card
ProDAQ 3808
-
The ProDAQ 3808 function card, an enhanced version of the ProDAQ 3806 counter/timer function card, is designed to operate in one of three modes: pulse counter, frequency meter, or time interval counter. In the pulse counter and frequency measurement modes, users can process incoming signals of up to 25 MHz on each of the six channels. A time interval counter range is divided into six sub-ranges, covering times from 40 ns to 20000 s with a maximum resolution of 10 ns. For pulse-width measurements, the same ranges apply.
-
Product
Advanced Probe Card / V type
VC Series
-
Japan Electronic Materials Corp.
*Vertical contact Probe Card*No limitation by Pad layout*Large probe area (Suitable for 200mm wafer 1-shot)*Small scrub mark*Suitable for High/Low Temperature Test
-
Product
2 Ports 25GbE SFP28 Network Mezzanine Card
NMC-2501
-
1 x Intel® XXV710DA2, 2 x SFP28 slots, 1 x PCIe x8, Gen3, RoHS compliant.
-
Product
ABex Terminal Module for Göpel 1149Cx BSCAN Cards
ABex TM-1149Cx
-
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1k
50-265-204
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Electronic Cards
-
Our product range includes a wide range of PDBC Relay Card, Local Remote Selector Card, Monitor Card and Fuse Failure Relay Card.
-
Product
Probilt™ Probe Card Analyzers
-
ITC has a complete range of probe card metrology products that address all probe technologies, probe card sizes and probe counts.
-
Product
PXI 2-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-202-24X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC is a range of high-density matrix modules able to switch up to 2 Amps at 150VDC/100VAC They are available in 2, 4 or 8 slot PXI sizes to suit most high-performance PXI Matrix requirements and constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 52.4kΩ
50-298-033
Programmable Resistor Modules
The 50-298-033 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express Digital I/O Card With Counters And IRQ
PCIe-DIO-24HC
-
This product is a x1 lane PCIe DIO board with basic DIO, Counter/Timers and interrupt generation capabilities. The card uses an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C is further broken into two 4-bit nybbles via software, configured as either inputs or outputs.
-
Product
Clock and Trigger Distribution Card
-
The clock and trigger distribution card is a simple and passive component that allows to synchronize several systems externally. No programming is necessary. A clock can be fed in from an external device or as an option an internal clock oscillator can be equipped by the factory. This clock is then also used to synchronize an external trigger signal into the clock domain. Both, clock and synchronized trigger, are then fed into a maximum of 17 different systems. Each system can be a single card or a synchronized set of cards that run with an internal star-hub.
-
Product
LVDT I/O Cards
CPE4000
-
Computer Conversions Corporation
Computer Conversions’ CPe4000 Series are CompactPCI-Express (cPCIe) and PXI Express (PXIe) compliant: Synchro, Resolver, and LVDT/RVDT I/O Cards (predominantly output cards), with GEN1 and GEN 2 PCI Express interface, designed for accurate and reliable commercial, industrial and COTS-Mil. applications in test, simulation, motion control and shipboard data distribution. The CPe4000 Series drive up to 4 channels of Synchro, Resolver, 3-wire LVDT/RVDT outputs, or up to 8 channels of 2 wire LVDT/RVDT AC Sensor output sets.
-
Product
LXI Function Card Carriers
ProDAQ 6100 Series
-
Ethernet-based LXI is changing the way engineers and scientists perform test and measurement and data acquisition. As more and more PCs ship without expansion slots, customers are faced with the problem of replacing their test and measurement and data acquisition equipment. Bustec believes in the power of distributed systems and the use of IEEE standards.
-
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 5.82MΩ
50-298-152
Programmable Resistor Modules
The 50-298-152 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 22.3MΩ
50-298-154
Programmable Resistor Modules
The 50-298-154 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
16, 32, or 48 Channel Isolated Digital Input Cards
PCI-IDI Series
-
PCI-IDI-xx Series cards offer a range of 16, 32, or 48 individual, optically isolated inputs. These cards are ideal for use in control and instrumentation applications where high-voltage protection is required. Individual channel-to-channel isolation allows every channel to be physically and electrically separated from the others.
-
Product
Gigabit Ethernet PCI Express Mini Card
mPCIe-LAN-GbE
-
The mPCIe-LAN-GbE is a type F1 PCI Express Mini Card (mPCIe) optimized for use in mobile and rugged environments, with latching connectors and protection on all signals. The onboard magnetics feature robust built in isolation via transformer coupling. In addition, extended operating temperature and RoHS compliance are standard.
-
Product
Digital I/O Card w/CoS IRQ
mPCIe-DIO-24S
-
The mPCIe-DIO-24S is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
NVIDIA GPU Cards
-
Graphical cards for AI/VR applications with NVIDIA hardware GPUs that provide powerful libraries that can be leveraged to build your programs.
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 6.97kΩ
50-297-124
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
Analog Input Module
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 350 Ohm
50-265-012
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
-
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
