-
Product
WaveLink Temperature Extension cables for Dx10
Dx10-HiTemp
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
WaveLink Temperature Extension cables for Dx20
Dx20-HiTemp
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Temperature data loggers
-
Our temperature data loggers and temperature recorders allow temperature logging from any temperature sensor type like thermocouples, RTDs, and thermistors. Temperature loggers are modular by design and can expand from 1 to 1000's of temperature measurement points. Simple to set up and use. Free award-winning Dewesoft X data acquisition software included.
-
Product
Temperature Controlled Water Bath
WB
-
Digital temperature controllerStainless steel tank with structural steel baseTiming circuit refreshes water for a full two minutes each hour preventing buildup of weak acid and stale waterWater level adjustable by standpipe changeOverhead wire tray with openings for optional test leadsHolds 15 SLI storage batteries (BCI group 24)
-
Product
Humidity and Temperature Measurement Accessories
-
Find our selection of most frequently used accessories such as filter and filter carriers to protect your sensor against mechanical influences or a range of accessories for mounting, connecting, installation, maintenance and calibration of your humidity and temperature instruments.
-
Product
Temperature & Humidity Sensor Breakout Board
Si7021
-
Sensor for Silicon labs has ± 3% relative humidity measurements with a range of 0–80% RH, and ±0.4 °C temperature accuracy at a range of -10 to +85 °C. Great for all of your environmental sensing projects. It uses I2C for data transfer so it works with a wide range of microcontrollers.
-
Product
Digital Temperature Sensor
ZET 7121
-
Digital temperature sensor ZET 7121 is intended for measuring temperature of liquid, solid, gaseous, and bulk mediums, unaggressive to the thermistor body material. Application scope: heat engineering, chemical industry, and metallurgy. The digital temperature sensor consists of a thermistor and ZET 7121 measuring unit which converts the signal from the sensor to temperature values. Thermistor type is selected in accordance with the specifics of the task to be solved: measurement and accuracy required ranges, operation conditions.
-
Product
Temperature, Humidity, Pressure and Gas Sensor
BME680
-
The BME680 is a digital 4-in-1 sensor with gas, humidity, pressure and temperature measurement based on proven sensing principles. . This little sensor contains temperature, humidity, barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price!
-
Product
Temperature Data Logger
-
The temperature recording in a process is the most common and widely required application in any process. The commonly used temperature sensors are RTD Pt100 / Pt1000/ Cu53 / Thermistors and different kinds of Thermocouple. In order to avoid electromagnetic interference, the temperature signal is converted to 4-20mA and is carried to the logger. Our range of Temperature Data Logger includes Temperature Humidity Logger, RTD Data Logger, Thermocouple Data Logger and Flameproof Data Loggers.
-
Product
Low Temperature Remote Probe Logger
TREL-8
-
TREL-8 is easily configured for recording conditions including delayed start, sampling interval, number of readings and configuration of conditions to activate the ALERT indicator. Readings are downloaded using LogTag® Analyzer which provides facilities for charting, zooming, listing data statistics and allows exporting the data to other applications such as Excel.
-
Product
Temperature logger-40 to 85C
TK-4014
-
This logger is self-contained with an internal temperature sensor. It can measure temperatures between -40 to 85C. The unit is designed primarily for indoor use but is splashproof to IP54.
-
Product
Fast Temperature Shift
CherryTemp
-
CherryTemp is a temperature controller based on two independent Peltier channels, allowing for very accurate temperature control and ultra-fast shifts from 5°C to 45°C. A thermalization liquid circulates from a reservoir to the heat exchangers (heating/cooling Peltier elements) where it is thermalized to a target temperature. Once thermalized, this liquid can be quickly injected to a microfluidic device (CherryTemp chip) mounted near the sample. Because of the small thermal mass (the distance between the microfluidic chip and the sample), the temperature transfer is very fast (less than 10 seconds) and of unprecedented accuracy due to a feedback loop control of the room temperature and the heat-sink played by immersion objective lenses.
-
Product
Temperature and Humidity Transmitter
T3319-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Temperature & Environment Monitors
Room Alert
-
Monitors Temperature, Humidity, Power, Flood/Water, Smoke/Fire, Motion, Room Entry, Air Flow, Panic Buttons, Network Cameras and more. Offers built-in sensors & allows external sensors to be added.Allows unlimited alert notifications & unlimited users. Allows notification via email, SMS, SMTP, dial-out page, audio alert, webpage update, logfile update and more.
-
Product
Intrinsically safe humidity and temperature transmitter
T3110Ex
-
Built-in relative humidity, temperature sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Electronic Circular Temperature Chart Recorder
-
The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.
-
Product
Logger version conductivity and temperature sensor
INFINITY-CT A7CT-USB
-
Infinity-CT is an autonomously deployable data logger for temperature and salinity measurements. The conductivity sensor has a design of 7-electrode. The small-sized instrument (Φ54mm x 255mm, 0.7kg in air) can be deployed and integrated virtually anywhere. The instrument has two depth rating versions: shallow water (200m, A7CT2-USB) and deep water (2,000m, A7CT-USB).
-
Product
LoRaWAN Temperature Probe Sensor
LEO-S572-TP
-
LoRaWAN Temperature Probe Sensor for Cold Chain and Hot Environments, 3 wire connection for high precision, LoRaWAN technology for efficient long-range wireless data transmissions. IP67 waterproof enclosure for harsh environment applications, Built-in 19000 mAh replaceable battery and long battery without replacement.
-
Product
Temperature and Humidity Probe
T3313
-
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
USB PDF Temperature Logger
UTRIX-16
-
The LogTag® UTRIX-16 satisfies the growing need for a cost effective and reliable multi-use temperature logger. It requires no special hardware or proprietary software to access the recorded data and can generate a fully detailed PDF report. The UTRIX-16 stores real-time temperature readings over a measurement range of -25°C to +70°C (-13°F to +158°F), displays user-configurable alerts, and comes with an integrated, long-life USB connector.
-
Product
Compressed Air Temperature and Humidity Regulator
H3021P
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Cryogenic Temperature Sensor Information
-
A detailed explanation of the process and outcomes of our temperature sensor calibrations are contained.
-
Product
Temperature Switch
T150D
-
The T150D Adjustable Stainless Steel Miniature Temperature Switches provide the end-user with a wide range of functionality without impacting durability. The T150 is designed for use up to 510°F but can withstand temperatures up to 800°F while still protecting the set point and life of the switch. The limit filled, saturated vapor sensor is in direct contact with the temperature-sensing outer shell producing fast response and accurate temperature control. The external setting scale provides full range adjustment and the external lock screw allows for easy adjustment of set point.
-
Product
Temperature & Process Calibrators
-
The most sophisticated industrial equipment will not be useful unless it is calibrated. GAOTek Process Calibrators are used to adjust instruments’ accuracy, and they are the only process calibrator you will ever need to carry. They can measure temperature, pressure, voltage, resistance and frequency, and can be used during troubleshooting. Through calibration, you can ensure that any equipment performs as expected and that it can be relied on to deliver predictable and accurate results that meet quality standards. GAOTek Process Calibrators come with a USB interface which makes it easier to transfer the results to other devices which otherwise would have taken a long time to transcribe them. Our Process Calibrators are for sale to the United States, Canada and globally.
-
Product
Fixed Infrared Temperature Sensors
-
This fixed infrared sensors selection is vast with many different features without any lack in quality. These infrared sensors are designed for fixed continuous non-contact temperature measurement.
-
Product
Temperature and Humidity Regulator
H3021
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Temperature Calibration
-
In our temperature lab we have the capability calibrate a wide range of temperature products such as catering food probes from deli to restaurant, industrial systems for manufacturing and quality checks using thermocouples surface probes or insertion probes we also calibrate IR (Infrared) thermometers.
-
