CSA
Canadian Standards Association
-
product
4.0mm Hazardous Live Parts Probe
CX-4.0
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts through top openings. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN61010-1, UL3101-1, and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is made of stainless steel.
-
product
Power Line Purpose Tester
LX-221A+
Shenzhen Lian Xin Technology Co., Ltd.
·Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .·Used to test single – ends ,double –ends ,three-ends power supply cords.·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,·Provide with RS 232 interfaces, can communicate with PC, easy to upgrade,·Provide personalized customization according to different requirements.
-
product
Automated AC Digital Hipot Tester
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
product
Hipot & Safety Test
Chroma Systems Solutions, Inc.
Electrical safety tests to comply with IEC, UL, TUV, CSA, EN, and other electrical safety requirements.
-
product
Saluki CSA Series Signal Analyzer (Modular)
Saluki CSA series signal analyzer reaches the frequency from 100 kHz to up to 26.5 GHz with a maximum of 40 MHz analysis bandwidth. It can test signal power, frequency, phase, P-1, TOI, OBW, channel power, spurious, ACPR, CCDF, SEM, EVM, and other indicators. It can be used independently or combined with the chassis to form a test system.
-
product
Guardian Hipot Analyzer
19055
Chroma Systems Solutions, Inc.
Hipot or dielectric withstand testing instruments manufactured by Chroma are used for conducting electrical safety tests on electrical components and products to make certain they are in compliance with IEC, UL, TUV, CSA, EN and other electrical safety requirements. In addition, these instruments are designed for general product or component testing as well as complex medical safety testing (60601-1) ensuring human safety and product reliability.
-
product
Short Test Pin Probe
Probe 13
Shenzhen Chuangxin Instruments Co., Ltd.
Short Test Pin Probe 13 The model CX-13 short Test Pin Probe is used to test for accessibility of small objects and meets IEC, CSA and UL requirements.
-
product
IEC-IEEE-CSA-IS Standards
MOTOMEA RDS Automatic IEC-60034-2-1 Test Bench solutions are complete turnkey systems and provide a full implementation of the IEC 60034-2-1, IEEE 112-2004, CSA C390-10 standards
-
product
Hipot Tester
Sentinel
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
product
Diaphragm Operated Dual-Action Pressure Switch
H2
Explosion-proof, UL & CSA Listed for Class I, Groups B, C & D and Class II, Groups E, F & G. The H2 is designed for sequencing two different actions as pressure of a liquid or gas increases or decreases. The patented design consists of two concentric pistons operated by a single diaphragm with one pressure chamber.
-
product
Oxygen Transmitter
Model InstaTrans-XD
Teledyne Analytical Instruments
This model utilizes a design to meet the requirements of NEMA-4(IP-66) levels as well as ATEX Zone 0/1/2 and FM/FMc Class I Div 1 approvals when used with select intrinsic safety barriers. In addition, the CSA approval extends to Class I Div 2 as a non-incentive device without the use of barriers. The transmitter head contains the electronics and user display interface including 4-button design to access functions.
-
product
Low Differential Pressure Switch -
1800
Essential for industrial environments, the Series 1800 combines small size and low price with 2% repeatability for enough accuracy for all but the most demanding applications. Set point adjustment inside the mounting stud permits mounting switch on one side of a wall or panel with adjustment easily accessible on the opposite side. UL and CSA listed, and FM approved.
-
product
AC Current Shunts
CSA Series
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
-
product
IEC60068-2-75 Spring Operated Impact Hammer
CX-T04
Shenzhen Chuangxin Instruments Co., Ltd.
This Spring Impact hammer is strictly designed according to IEC60068-2-75, IEC884 and UL1244 GB/T2423.55-2006, GB4706.1, GB8898 and GB7000 standards. It is used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC\EN, \UL\CSA and other international Standards.
-
product
Pressure Transmitters
Explosion-proof pressure transmitter is approved for use in hazardous locations per CSA Standard 30 and UL Standard 1203 for Class 1, Division 1 and Division 2 hazardous locations. Wetted parts are all 316L Stainless Steel (50 up to 10000 PSIG), 17-4PH (15000 & 20000 PSIG) for compatibility with a variety of media. Wetted materials and construction comply with the NACE MR0175 Standard. The KP46 Series explosion-proof pressure transmitter's fitting and sensing diaphragm are machined out of a single piece of material, so there are no welds, seams or O-ring seals, resulting in excellent long-term performance and stability. The case is factory sealed, making this pressure transmitter very rugged with excellent shock and vibration resistance.
-
product
AC-DC POWER SUPPLIES
Universal Input 85-264 VACContinuous Short Circuit ProtectionPCB MountableEfficiency to 82%Industry Standard Pin OutMeets, UL, CSA, TUV CE
-
product
Listed Circuit Breakers
Mitsubishi Electric Automation, Inc
To meet the demands of the U.S. and Canadian markets, the UL listed MCCB and ELCB products are compliant to UL489 and CSA C22.2 No.5-02 This range of breakers series offers a standard and high performance protection up to 630 amps and are easily installed in the field accesories.
-
product
IEC60950 50mm Impact Test Balls
CX-15
Shenzhen Chuangxin Instruments Co., Ltd.
The Impact Test Ball is a specially machined ball to test impact resistance according to IEC, CSA and UL Standards. It is made of chrome-plated-steel for durability, and is fitted with an eyelet to facilitate testing for pendulum applications. Eyelet is threaded to the ball to allow attachment of a handle or force gauge. Weights are closely controlled.
-
product
Rigid Finger Probe
CX-Z15
Shenzhen Chuangxin Instruments Co., Ltd.
A ¨rigid〃 version of the International Test Finger, model TFP-01, (see next page). Used for force applications on openings (i.e. vents) as required by IEC, EN, UL and CSA Standards. Handle made of Delrin, rigid finger made of chrome plated steel.
-
product
IEC61032 Jointed Finger Probe
CX-2B
Shenzhen Chuangxin Instruments Co., Ltd.
Jointed Finger Probe This is the "international" test finger required by most IEC, EN and CSA standards, in addition to many UL standards.
-
product
IEC60068-2-75 Impact Spring Hammer Single Energy
CX-T02
Shenzhen Chuangxin Instruments Co., Ltd.
Required by many Standards to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC, EN, UL, CSA and other international Standards.
-
product
Backflow Prevention Test Kit
BTK2
he Model BTK2 Backflow Prevention Test Kit is capable of testing hydronic systems with test procedures recommended by ASSE, AWWA, CSA, FCCC, HR-USV, and NEWWA. The BTK2 is comprised of three valves and is specially designed for testing backflow prevention assemblies. The tests can be completed in almost any area by mounting the unit with the included high performance elastic cord. PTFE-lined brass ball valves simplify the adjustment procedure. The large, easy-to-grip needle valve allows for quick adjustment.
-
product
Current Probes
Tektronix current probe solutions offer:*The broadest range of AC/DC and AC-only current probes*Measurement accuracy from uAs to 2000 A*Best-in-class bandwidth up to 120 MHz*Best-in-class current clamp sensitivity down to 1 mA*The only products with 3rd Party Safety Certification (UL, CSA, ETL)*The only products with bare wire voltage ratings*Automatic readout and scaling when used with Tektronix oscilloscopes so you don’t have to convert volts to amps or manually set the scaling
-
product
Single, Double Power Cord Tester
LX-30A+
Shenzhen Lian Xin Technology Co., Ltd.
Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .．·used to test single – ends ,double –ends ,three-ends power supply cords.．·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,．·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,
-
product
PPID-2000 Photosynthetic Photon Intensity Distribution Test Unit
Hangzhou Everfine Photo-E-Info Co., LTD
It is mainly used for testing plant lighting products. With the EVERFINE GO-R5000 goniophotometer system, it can realize the measurement of plant photosynthetic photon intensity distribution (μmol/s/sr) in the whole space. In addition, the device can also realize the test of photosynthetic photon flux, far red light photon flux, photosynthetic radiation efficiency and other parameters, referring to DLC, ASABE, DIN, GB, CQC and CSA related international plant lighting standards .
-
product
SP-20 Spectral Photosynthetic Radiometer
Hangzhou Everfine Photo-E-Info Co., LTD
SP-20 test speeds up to milliseconds. It realizes the measurement functions of spectral power distribution, photosynthetic radiation parameter, optical quantum parameter, photo-electrical parameter, and it also realizes the quantity conversion between the three measurement systems. Refer to DLC, ASABE, DIN, GB, CQC, CSA and other international plant lighting standards.
-
product
Flexible Current Sensor Probe
CTA
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
product
GFCI Receptacle Tester
RT210
Conforms to UL Std 1436, Certified to CSA Std C22.2 #160.Built to withstand a 6.6 ft. (2m) drop.Operating temp: 32°F to 140°F (0°C to 40°C).Works on GFI outlets and confirms operation of the ground fault.Nominal Voltage: 110/125V AC at 50/60Hz in 3-wire outlet.
-
product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
product
3D Compliance SAR System
cSAR3D
Schmid & Partner Engineering AG
cSAR3D is our newest and most advanced system for fast, high-precision SAR measurements of wireless devices. We have realized a system concept that has been developed over the last years to meet the demands of our highly valued customers. The system uses a novel sensor concept and advanced reconstruction algorithms. The measurement system has high absolute accuracy due to the determination of all field components in a large region of the head and body phantoms.
