Breakout Boxes
reroute signal paths to facilitate contact accessability.
See Also: Boxes, Breakouts, Decade Box, Anechoic Boxes, Black Box, Hot Box, White Box, Shielded Box, RF Box, Programmable Resistance Box
-
Product
UHD Set-Top Box Processors
-
ST’s set-top box SoCs bring a world of media into your living room. Our UHD portfolio offers high-end solutions for 4K broadcast content as well as supporting internet media and operator-specific applications.
-
Product
SparkFun BabyBuck Regulator Breakout
3.3V (AP63203)
-
Who doesn't occasionally need power regulation? We certainly do, so we've designed the SparkFun BabyBuck Regulator Breakout to help us with just such a task. Featuring the AP63203 from Diodes Inc, this breakout board takes advantage of a 2A synchronous buck converter that has a wide input voltage range of 3.8V to 32V and fully integrated 125mΩ high-side power MOSFET/68mΩ lowside power MOSFET to provide high-efficiency step-down DC/DC conversion. All of this snuggled up in a low-profile, TSOT26 package that's integrated into a 0.4in by 0.5in board.
-
Product
SparkFun Pulsed Radar Breakout
A111
-
Does your project require high-precision, cutting-edge distance measurement? Or maybe speed, motion, or gesture-sensing? We're not talking about simple ultrasonic or even infrared here, but 60GHz radar! Well say hello to the SparkFun A111 Pulsed Radar Breakout! The A111 is a single-chip solution for pulsed coherent radar (PCR) and comes complete with an integrated antenna and an SPI interface capable of clock speeds of up to 50MHz. Though the A111's primary use case is distance-sensing, it also supports applications in gesture, motion, material, and speed-detection at distances of up to two meters.
-
Product
SparkFun Transceiver Breakout
RS-485
-
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
Product
SparkFun FTDI Basic Breakout
3.3V
-
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
-
Product
SparkFun RJ11 Breakout
-
This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the board to match a standard telephone wire. Additionally, each board has pin numbers on the back side that match with the pins on the connector.
-
Product
SparkFun USB UART Serial Breakout
CY7C65213
-
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running.
-
-
Product
SparkFun Current Sensor Breakout
ACS723
-
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
SparkFun Mono Audio Amp Breakout
TPA2005D1
-
This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can drive an 8-Ohm speaker at up to 1.4 Watts; it won't shake a stadium, but it will provide plenty of volume for your audio projects.
-
Product
RF Shield Box
-
A small versatile manual shielding box that is designed for small scale device testing such as wireless network cards and wireless communication equipment.
-
Product
SparkFun SD/MMC Card Breakout
-
With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown.
-
Product
SparkFun GPS Breakout
XA1110 (Qwiic)
-
The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to our Qwiic Connect System. Equipped with the XA1110 GPS module from GTOP, this board utilizes the MediaTek MT3333 chipset, loaded with specialized SparkFun firmware that enables both I2C and serial ports simultaneously. Using I2C means you won’t have to tie up your serial port with GPS, leaving it open to other possibilities.
-
Product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
-
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
Product
SparkFun MicroSD Transflash Breakout
-
Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested.
-
Product
Edge-AI Box
DS-011
-
DS-011, an Edge-AI Box with 2 UHD HDMI ports, is designed for AI applications, making it ideal for interactive AI displays. Power by Qualcomm Dragonwing™ 8-cores QCS6490 2.1Ghz. Hexagon™ 770 AI Engine up to 12 TOPS. Triple-ISP for camera up to 192MP capture.
-
Product
SparkFun USB-C Breakout
-
With this USB breakout you will finally be able to incorporate a USB-C connector into your projects without needing to solder each tiny SMD pad. The SparkFun USB-C Breakout supplies up to three times the power as previous USB iterations and also solves the universally frustrating dilemma of plugging a USB cable in correctly because it's reversible!
-
Product
SparkFun Level Translator Breakout
PCA9306
-
There are a couple must-have boards that every engineer and hobbyist should have on their desk, and this PCA9306 dual, bidirectional voltage-level translator breakout is one of them! Because different parts sometimes use different voltage levels to communicate, voltage level translators can be the key to making different parts play nice.
-
Product
POWER INTERFACE BOX
-
The POWER Box is in charge to provide power supply lines towards the UUT simulating the power distribution unit. The box has been designed to host, in any mixed configuration, two kind of plug in modules:
-
Product
Lightning Sensor Breakout
SEN-39001
-
Breakout board for the AS3935 digital lightning sensor based on the AMS reference design. Includes specially tuned antenna, SPI or I2C interfacing, and a wide 2.4V to 5.5V standard operating range. This innovative sensor is designed to interface with most current development systems and boards, including all current Arduino modules. The breakout board features an inductor (antenna) specially designed for this application, and the board ships fully calibrated. This ensures that you don't have to write a massive back-end to support low-level IC calibration, just focus on your final application!
-
Product
SparkFun Triple Axis Accelerometer Breakout
KX134 (Qwiic)
-
This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX134 digital accelerometer from Kionix. The KX134 is a low-power, 16-bit resolution three-axis accelerometer capable of measuring ±8g/16g/32g/64g (user-selectable) and has up to a 10kHz output data rate making it ideal for high-g measurements as well as high-speed applications such as vibration sensing.
-
Product
SparkFun Altitude/Pressure Sensor Breakout
MPL3115A2
-
Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it's easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements in degrees Celsius.
-
Product
RF Shielded Box
TS7124
-
R&S®TS7124 RF shielded boxes enable reliable and reproducible measurements in shielded test environments. The R&S®TS7124 shielded box provides high shielding effectiveness, a good antenna coupling factor and a rugged mechanical design for reproducible results. RF test boxes have been designed not only for product designers or product optimization but also for production lines of wireless devices under test. The soft close feature makes the shielded box safer to operate.
-
Product
Dual MAX31865 PT-1000 RTD to Digital Breakout
SEN-30202-PT1K
-
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information.
-
Product
ICI Pilling Box Tester
UI-TX05
-
ICI Pilling Box Tester is used to assess fabric surface pilling and fuzzing by tumbling randomly. This pilling test machine is also called as ICI pilling and snagging tester/ICI pilling box. ICI pilling box test method includes ISO 12945.1, BS 5811, GB/T 4802.3, JIS L1076, etc.
-
Product
19" Breakout & Power Input Panel
Cabinet CP-103
-
The CP-103 is breakout and power input panel which is used to provide a clear connection interface for 19” racks. It is equipped with the most common interfaces found on industrial computers. In addition, it provides a single phase 16A CEE connector and a brush to feed through additional cables and tubes. Furthermore, it’s M6 threaded plate installed to simplify equipotential bonding.
-
Product
SparkFun LTE GNSS Breakout
SARA-R5
-
The SparkFun SARA-R5 LTE GNSS Breakout is a robust development tool for u-blox's impressive SARA-R510M8S module. The SARA-R510M8S combines u-blox's UBX-R5 cellular chipset with their M8 GNSS receiver chipset to provide a 5G-Ready wireless IoT device complete with positioning data all on a single chip. As an asset tracker, the LTE GNSS Breakout offers Secure Cloud LTE-M communication for multi-regional use and has an integrated u-blox M8 GNSS receiver for accurate positioning information.
-
Product
RF Shielded Box
LTL B2001
-
LTL B2001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B2001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
50 Pin IDC Connector Breakouts
-
The connector breakouts below are suitable to use with Pickering cabling products that utilize a 50-pin IDC connector.
-
Product
SparkFun OpAmp Breakout
LMV358
-
This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the caps removed. The LMV358 opamp can source up to 160mA and works well as a low impedance driver/buffer.
