Phasor Measurement Units
synced remote wave monitors measuring ac current and voltage on a power grid. Also known as: PMU
See Also: PMU, Smart Grid
-
product
Mask Flatness Measurement System
Tropel® UltraFlatTM 200 Mask System
The Tropel® UltraFlatTM 200 Mask System was designed specifically for the photomask industry. It delivers the lowest measurement uncertainty for ever-tightening mask flatness specifications. Shrinking device features require not only flatter wafers, but flatter masks.
-
product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
product
Miniature Measuring Amplifiers
MAL Series
5B connection technology is based on the common 5B industrial standard and is intended to be a supplement to the 5B measuring amplifiers
-
product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
product
Spectral Light Meters For Photometric And Colorimetric Measurements
Comprehensive range of spectroradiometers for the measurement of illuminance (lux), luminance (cd/m²), luminous flux (lumens), luminous intensity (cd) as well as the colorimetric characteristic values such as chromaticity coordinates (x,y,u',v') or color rendering index (CRI), etc.
-
product
Reliable CAN Measurement Technology
CNT evo CAN MM Series
The CNT evo is a high-precision measurement module designed for measuring frequencies, pulse widths, incremental displacement measurements, rotation angles, position measurement, event counting and period measurements.
-
product
Interface Units
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
product
Entry-level Price Interferometer for Geometry Measurement of Single Fibers
3D SCOPE-V2
Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.
-
product
Front Panels for Plug-In-Units | IEC
Front panels for plug-in-units according to IEC | with or without EMC protection | aluminum 2.5 mm | clear anodised
-
product
Portable X-RAY Fluorescence Measuring System
FISCHERSCOPE® X-RAY XAN® 500
Mobile and universal handheld device for precise coating thickness measurement and material analysis - even with difficult material combinations.
-
product
Switching Unit
ZET 454
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Emergency Power Supply Unit (EPSU) (8) 5-15R 1U/0U V/H
EPS-815-HV
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Multiport Calibrated Measurements With Switch Instruments
S97553B
This application provides a macro which enables full multiport error correction and measurement capabilities using external switch instruments
-
product
Temperature Measurement IR Sensors & Detectors
ST150 With Diffractive Lens
A single-channel silicon-based thermopile with integrated diffractive lens and internal baffle that delivers a very low Temperature Coefficient of Responsivity of -0.04%/C with a high output voltage, 19.5 FOV and a quick time constant of 38ms. This Low-cost detector comes in a TO-5 package and has a very short thermal shock response to ambient temperature change.
-
product
Temperature Measurement System
TMM-100
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
product
Coordinate Measuring Machine
SF87
Entry-level CMM for the production environment. WENZEL’s SF87 has the attributes needed for a shop floor CMM and benefits from an optimum measuring volume of 800 x 700 x 700 mm , its cantilever style configuration providing a very efficient footprint relative to measuring range.
-
-
product
Level Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Level trainer is a table top module, it comprises of measuring tank of 50 CM length, sump tank and load cell capacitance as level sensor. A vertical pump is fitted circulate the water. Digital display indicator is provided display water level in cm
-
product
Level Measurement
As a market leader in level detection with the largest selection of agency approved level switch technologies, the K-TEK level products line has the proven technology to provide solutions for the most difficult liquids and solids level applications.
-
product
Water Source Measurements You Can Count On
TechPro™ II (TP1, TPH1)
Obtain reliable and accurate measurements of your water source with the value-priced TechPro II™. Ideal for water treatment testing as well as other industrial and commercial applications, these instruments reflect Myron L®’s 55-plus years experience designing and building quality conductivity, TDS and pH measuring instrumentation.
-
product
Peak Power Measurement
Directly measure the instantaneous peak power level of a pulse modulated signal. Use the "sample delay" function to set the desired measurement point on the waveform. And an external scope can be used to view the profile and see the exact measurement point on the pulse.
-
product
Automated Measurement Expert (AMX), VNA Plugin
S94702A
The Keysight automated measurement expert (AMX) is a smart software solution for automated multiport S-parameter measurements with the PXIe vector network analyzers M937xA/M9485A or the benchtop E5080A ENA network analyzer. The S94702A AMX VNA plugin adds S-parameter measurement capabilities to the Keysight test automation platform (TAP). The combination of the TAP and the VNA plugin forms the AMX backend software, which makes the VNA setups and executes the test sequences in the PXIe controller according to the optimized test sequence files generated by the AMX test plan builder. Other instrument plugins allow you to control the DUT mode, expand the number of test ports with the PXI switches or multiport test set, and use external instruments such as a DC power supply and a digital multimeter. The AMX backend software also provides step-by-step calibration wizard for full multiport calibration using the 4-port ECal module.
-
product
3U cPCI Sensor Interface Unit
SIU31
NAI's SIU31 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU31 uses one NAI field-proven, 3U cPCI board to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
product
Dual-Channel Precision Audio Analyzer with Built-In Condenser Measurement Mics
PAA6
Essential tools, such as the Phonic PAA6 Professional Audio Assistant generally wind up at the bottom of pro audio wishlists after esoteric preamps, compressors, and EQs. But more often than not, the key to great sound lies in the utilitarian gear, particularly, the Phonic PAA6 audio analyzer. If you want to get the most out of your studio equipment or PA system, the PAA6 should be at the top of your bucket list. A highly accurate measurement tool, the elegant touch screen interface of the PAA6 offers unfettered access to 61-band real-time spectrum analysis; Fast Fourier Transform (FFT); sound pressure (SPL) and dBu/dBV line voltage measurement; EQ setting; phase and polarity check; LEQ (equivalent continuous noise level); audio oscilloscope; and RT-60 functions. The PAA6 also has two built-in condenser measurement mics that can be used in six different positions. If sound is your product or passion, the Phonic PAA6 is perhaps the wisest investment you can make for your studio or sound reproduction system. Whether you're setting up monitors, treating room characteristics, calibrating listening levels, or want to know the harmonic distortion and noise characteristics of your workhorse preamps to ensure clean mixes, the Phonic PAA6 is your key to the best possible quality sound.
-
product
Length Gauges For Measuring Stations And Multi-gauging Fixtures
METRO series
*High repeatability*Very high system accuracy of down to: ±0.2 µm*Ball-bearing-guided and zero-backlash plunger*Variant with reduced gauging force*Very long measuring ranges of up to 100 mm*Interfaces: 1 VPP, TTL, 11 µAPP*Protection rating of up to IP67
-
product
Gain-Compression Measurements
S96086B
The S96086B, gain compression measurements provides fast and accurate characterization of input power, output power, gain, and phase at the compression point of an amplifier, over a specified frequency and power range, with a simple setup
-
product
1 10/100M/1000M LAN FTTH EPON ONU ( Optical Network Unit )
ONU-1GE
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ONU-1GE optical network unit (ONU), based Gigabit Ethernet Passive Optical Network FTTH EPON system user side equipment, combined EPON OLT (Optical Line Terminal) via a passive optical network PON, to achieve a multipoint (P2MP) high-speed data transmission. Provides powerful data, voice and video and other broadband services to users..
-
product
Battery Loading Unit
BLUe
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
