Signal Level Meters
detect, measure, and monitor power or the intensity of a signal.
See Also: Level, Liquid Level, Level Transmitters, CATV Signal Level Meters, Satellite Signal Level Meters
-
Product
Field Strength Meters
FIM-22 And FIM-41
-
The Models FIM-22 and FIM-41 are portable field strength meters designed to provide precise, direct measurements of electro-magnetic fields in the 200 kHz to 5.0 MHz spectrum. These units include a receiver, integral shielded loop antenna, precision attenuator, internal calibration source, and battery power supply. With calibration accuracy traceable to the National Institute of Standards and Technology, the FIM-22 and FIM-41 meet the most exacting requirements of government and industry. Their hinged covers, on the rugged drawn aluminum cases, contain a loop antenna. Opening the cover to a vertical position connects the antenna terminals to the receiver via maintenance-free gold-plated contacts. An interlock switch prevents inadvertent battery discharge when the cover is closed.
-
Product
Video Signal Generator
MSPG-101
-
MSPG-101 portable tester is powered with built-in battery and DC power. Usef test to varied combination timings and patterns. MSPG-101notify TMDS information by accept input signal.
-
Product
Ultrasonic Meters
E-Series
-
E-Series Ultrasonic water meters from Badger Meter use solid-state technology in a compact, totally encapsulated, weatherproof, and UV-resistant housing, suitable for residential and commercial applications. Equipped with an easy-to-read, 9-digit LCD display, the ultrasonic meter reports consumption, rate of flow, reverse-flow indication, and alarms. With no moving parts, the E-Series Ultrasonic meter improves reliability and has greater extended low flow accuracy compared to mechanical meters.
-
Product
Scale / Weight Meter
-
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
In-circuit ESR Meter
Capacitor Wizard
-
The Capacitor Wizard® finds bad capacitors IN CIRCUIT by measuring a capacitor's ESR (equivalent series resistance). A good capacitor should have very low ESR. Weak and bad capacitors have much higher ESR. The Capacitor Wizard® will SPEED UP YOUR REPAIR.
-
Product
Signal Analysis Synthetic Instrument
SASI
-
Textron Systems’ SASI 240 is a Signal Analysis Synthetic Instrument that combines the capabilities of six distinct measurement systems into a single device. Our dual-channel architecture enables two independent radio frequency (RF) measurements to be run simultaneously. Whether used as a benchtop device or an integrated automated test equipment (ATE) RF subsystem, our SASI’s simple and intuitive graphical user interface (GUI) ensures easy, out-of-the box functionality.
-
Product
SWR / Power Meters
SX240C
-
Dimensions:170Wx115Hx150DmmWeight:1350gFrequency range:S1 (1.8-54MHz) S2 (140-470MHz)Power display rating:30W/300W/3kW(HF band only)Accuracy of full scale:±10%(F.S.)
-
Product
Noise Dose Meters
-
Here you will find a full range with an industrial standard noise dose meter to suit every requirement. With the portable noise dose meter you can carry out measurements quickly to gain control of a situation or to set the device to take timed measurements. The noise dose meter is important for all industries, especially by using it as a mobile device which is able to assess office stress levels or street noise levels.Often problems arise from noisy neighbors or if bars and restaurants are in residential areas and produce noise levels after 10pm in excess of what local laws permit. We, of course, can assess which noise dose meter you require in relation to the issue you have and the relating laws. We also have microphone extension cords, tripods, calibrators and calibration certificates for most models of noise dose meter.
-
Product
Clamp Meters
-
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Product
Wireless Meters
-
Digital Multimeter is loaded with the parameters and ranges HVACR professionals need for HVACR troubleshooting, plus it receives measurements wirelessly from any of the Fieldpiece Accessory Heads when connected to the wireless transmitter that''s included. You can now easily measure current, resistance, voltage, capacitance, frequency, continuity, and temperature either directly, or wirelessly from up to 75'' away.
-
Product
FieldFox Handheld Microwave Signal Analyzer, 32 GHz
N9960B
-
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Meter Test Switches
-
TESCO introduced the original Meter Test Switch in the early 1920’s. Today, TESCO’s line of Test Switches has been redesigned with the intention to combine the best features of tried and proven switching methods with improvements in materials and construction. All of the current carrying parts are bright tin plated to prevent corrosion. Good operating contact is assured on periodic meter tests, even when the switch has been idle for long periods of time in an unfavorable atmosphere.
-
Product
Clip-on Power Factor Meter & Watt Meter
-
Cambridge Instruments & Engineering Co.
Measurement of power factor in AC system on L.T. Circuits having higher current load without interrupting circuit.
-
Product
T6990 ENTRY LEVEL ABSOLUTE PRESSURE DECAY LEAK TESTER
-
T6990, recalculating the success of its predecessor M6990, an obviously enhanced user interface, thanks to an innovative tempered glass panel with built-in capacitive keyboard, around a 3.5” colour display.The new, high resolution display makes it even easier to view the test cycle and the programming menus, and the capacitive keyboard allows fast parameter entry.
-
Product
Ultraviolet Meter
UVR Series
-
UVR series is suitable to manage lamp of ultraviolet curing equipment, Also suitable to measure intensity of ultraviolet ray for sun light and lamp.
-
Product
Phase Angle Meter
-
Exceptionally fast response (up to 20 updates per second) and high accuracy for low frequencies, such as AC line frequency. A resolution of 1, 0.1 or 0.01 is user-selectable. Accuracy is 0.01% up to 100 Hz, 0.1% at 1 kHz, and 1% at 10 kHz.
-
Product
Wood Moisture Meters
-
Designed to measure the moisture content of wood, paper, plywood, and other wooden materials. This device classifies wood into four categories based on material density, and applies temperature compensation algorithm to ensure measurement accuracy.
-
Product
Meter Test Station
WECO 8000
-
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
Product
Dynamic Gravity Meter
TAGS-7
-
TAGS-7 represents the latest development in a long line of LaCoste-based airborne gravity systems, stretching back to the first successful airborne gravity flights in 1958 and building on the success of the TAGS System. For over 50 years, LaCoste gravimeters have acquired hundreds of thousands of line kilometers of gravity data during academic, government, and commercial surveys. TAGS-7 blends the latest in GPS and data acquisition technology with the solid foundation of the LaCoste dynamic gravimeter.TAGS-7 is an upgrade to the TAGS-6 gravity meter, and is designed specifically for airborne operations. The system incorporates a time-tested, low-drift, zero-length-spring gravity sensor mounted on a gyro-stabilized gimbal platform. The sensor has a worldwide gravity measuring range (no reset necessary) of 500,000 milliGals.
-
Product
Light Meter
LI-250A
-
The LI-250A is a portable meter that displays the output from any LI-COR light sensor that has a cable terminated with a BNC connector. It shows instantaneous values or 15-second averages of values from a sensor.
-
Product
Moisture Meters
-
Moisture meters are used to measure the percentage of water in a given substance. This information can be used to determine if the material is ready for use, unexpectedly wet or dry, or otherwise in need of further inspection.
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Vibration Meters
-
Overall Vibration Meter and Electronic Stethoscope, display unit with electronics includes: (2) "AA" batteries, (1) Sensor Pak, (1) Carrying Case, (1) Stereo Headphones with 3.5 mm "MINI" PLUG, (1) Owners Manual.
-
Product
Digital Light Meters
-
A selection of digital light meters including the GM1010 & GM1020 light level meters
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Signal Integrity Test Products
RoBAT SCARA-TDR-M
-
*Fully automatic TDR tester for bare and assembled PCBs*2 – 24 Port Ultra-compact TDR units*Full range of TDR tests and measurements available*100% test in a production environment*Custom modules with automatic tool changer
-
Product
Thermistor Power Meter
N432A
-
Keysight N432A is the replacement for Keysight's legacy 432A analog thermistor power meter. The single-channel, average RF power meter operates with the Keysight 8478B and 478A thermistor mounts. The N432A-and-thermistor-mount pair is ideal for applications that require high measurement accuracy, particularly in metrology and calibration laboratory environments. The enhanced thermistor power meter comes with a digital color LCD display, and user-friendly front panel interface. Its built-in calibration factor table provides a more convenient and accurate method of storing calibration factors as compared to the old knob-turning approach of the 432A. The N432A is LXI compliant, and programmable via GPIB, USB and LAN.
-
Product
Digital Meter
-
Shijiazhuang Suin Instruments Co., Ltd.
A meter is any device that measures and may record an electrical or magnetic quantity, such as voltage or current.
-
Product
Loop Meter
MZC-310S
-
The MZC-310S is a professional portable meter for testing electrical installations with over-current circuit breakers. The instrument measures short-circuit L-PE, L-N and L-L loop and prospective short-circuit loop current. A measurements can be done either with low testing current (up to 42A) with 2-pole method or high testing current (up to 280A) with 4-pole method that enables measurements with very high accuracy and resolution.
