Lamp
Radiate light or heat.
See Also: Flash Lamp, Arc Lamp, Flashlamp, Gas Lamp, Fluorescent Lamp, Headlamp
-
Product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
-
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
Product
Electronic Ballast Analyzer
WT3000
-
• It has 8 windows to display each parameter of input and output characteristics • Frequency response for testing input current up to 1MHz, suitable for precise testing of various kind of electronic ballast • WT3000 has expanding analysis for envelope wave. • Symmetry analysis for envelope wave’s crest factor of lamp current • Sampling at ultra-high speed, dynamic analysis single frequency curve, highest sampling frequency is up to 10MHz • Portable with built-in chip micro-processor, particular suitable for development and spot production • RS-232C standard interface can be connected to PC, English version software can run in WinXP or Win7
-
Product
Enlarge Environmental Chamber
REXMED REC-450
-
MOD. REC-450, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,644 Watts, 12,433 BTU/hr, 3,140 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
General Purpose Twin-Lead Tester
69136
-
Tests voltage in 90-250 volt range, AC or DC.Neon lamp glows indicating live circuit.The 5'' (127 mm) test leads have probes on the ends.Handy pocket clip.
-
Product
PCE-2000UV_1.5 Ultraviolet Light Radiation Measurement System
-
Hangzhou Everfine Photo-E-Info Co., LTD
PCE-2000UV UV light source radiation Measurement system can realize the measurement of the relative spectral power distribution of ultraviolet LED, UV fluorescent lamp, UV light source, peak wavelength, half-peak wavelength, spectral radiation flux of UV-A/B/C, and the total radiation flux in specific wavelength.
-
Product
Solar Simulators
Sun 2000 Class A
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house -no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
PXI 48 x SPDT Electromechanical Relays
40-148-101
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
Halogen Moisture Analyzer
LD-LHMA-A14
-
Halogen moisture analyzerLD-LHMA-A14with benchtop design, user can manually open the door of heating chamber for analysis. Incorporated with halogen heating lamp for rapid and uniform heating, it determines the moisture content and dry weight of the test sample. It continuously measures and immediately display the loss of moisture and weight on 5 inch touch LCD screen during test.
-
Product
CCD Spectroradiometer Integrating Sphere Compact System
LPCE-3
-
LPCE-3 is a CCD Spectroradiometer Integrating Sphere Compact System for LED Testing. It is suitable for photometric and colorimetric measurement of luminaries such as LEDs, LED luminaires, Energy-saving lamps, Fluorescent lamps, HID lamps (high voltage sodium lamps and high voltage mercury lamps) and CCFL. The measured data meets the requirements of CIE, EN and LM-79 clause 9.1 for the measurement of photometry and colorimetry.
-
Product
Light Source Colorimeter
CX-HP2
-
Shenzhen Chuangxin Instruments Co., Ltd.
Light source colorimeter is a newly developed pocket colorimeter, adopting advanced spectrometer and microprocessor technology. It makes traditional laboratory instrument available for the production on-line quality acceptance, thus greatly improve the efficiency of fluorescent lamp, CFL, LED manufacturing.
-
Product
CCFL Ballast Tester
WT2000A-CCFL
-
This tester is specially designed for analyzing the electrical characteristics of CCFL Electronic Ballast, meets the test requirements in international standard• Input characteristics analysis: measure Vrms, Irms, W, PF, Hz, phase angle Measure THD, 0 to 39th harmonic components, Accuracy: ±(0.4% reading+0.1% range+1 digit)• Output characteristics analysis: measure lamp voltage, lamp current, lamp power, oscillatory frequency, crest factor of lamp current, Accuracy: Class 2• Interface RS-232C provided for easier communication with PC for printing test report
-
Product
Trace-Level UV Fluorescence SO2 Analyzer
Model T100U
-
Teledyne Advanced Pollution Instrumentation
The Model T100U Trace-level SO2 analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven UV fluorescence principle, and is designed to allow ultra-sensitive SO2 measurements while still meeting the requirements for use as a US EPA compliance analyzer.The analyzer uses both the light and dark phases of the pulsed UV light source to continuously detect and correct for electronic noise, giving exceptionally stable and sensitive performance. A separate UV detector allows the instrument to continuously correct for variations in lamp intensity. Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift, and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon "kicker" and advanced optical design combine to prevent inaccuracies due to interferents.
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
Product
Spectral Radiant Flux / Luminous Flux Calibration Standards
-
Standard lamps calibrated in luminous flux and spectral radiant flux. Versions with 2-Pi and 4-Pi emission characteristics. Traceable calibrations in the wavelength range from 200 nm to 2500 nm.
-
Product
Solar Simulation
-
Sciencetech solar simulators produce high intensity, uniform illumination on a target area. Typically, high power solar simulators use an ellipsoidal reflector to capture light from an arc lamp source inside the reflector, an arrangement that results in a light pattern with a bright outer region and a dark center. This non-uniformity is un- acceptable in many solar simulator applications and as a result, forces many of our solar simulator competitors to use designs involving diffusers to reduce the non-uniformity. This results in a reduction of intensity and a dis- tortion of the spectrum on the target area.
-
Product
Climatic Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Climatic test chambers are also referred as environmental test chambers, which is the general name of various test chambers that simulate the natural climate environment of raining, high temperature, low temperature, constant temperature, illumination, dewing etc, products including constant temperature chamber, constant humidity chamber, ozone aging test chamber, UV accelerated weathering tester, vacuum hot air oven, salt spray chamber, steam aging tester, rain test chamber, dust proof test chamber, ventilation aging chamber, xenon lamp weathering test chamber and so on.
-
Product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
-
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
Product
Transformer Testing Panel
VTTP
-
Capable to Test Up to 25 MVA (Other Ranges are Available On Request). Useful for No Load Test (O.C.), Load Test (S.C.), DVDF Test HV Test of Transformer. Mains indication by R,Y,B indication Lamp. Over voltage, over current protection.
-
Product
Unregulated Power Supply Models
-
Low-cost DC power suitable for driving loads such as lamps, relays and small motors is provided by these unregulated power supplies. All components are generously derated, assuring a long and trouble-free life; built-in fusing prevents damage due to prolonged overloading or short circuits. They are housed in extruded aluminum cases which can be mounted in any position.
-
Product
Goniometer Systems
-
Our Goniometetric measurement systems are optimized to provide precise measurement of angle dependent spatial radiation properties of LED luminaires, lamps and other light-producing modules. Using a variety of photometric and spectroradiometric detector options, our goniometer systems achieve optical properties as a function of angle with accuracy, precision and speed.
-
Product
Constant Temperature Integrating Sphere
IS-*MT
-
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
Product
SUNTEST Family
-
Atlas Material Testing Solutions
SUNTEST instruments are compact material test chambers for accelerated lightfastness and weathering testing based on filtered xenon lamp technology. All SUNTEST chambers offer a horizontal test plane which is particularly useful for testing 3-D specimens. Lightfastness testing aims at testing a material under solar radiation and temperature only – Weathering testing adds water and moisture to the test.
-
Product
OES Spectrometers
-
OES Spectrometers (Optical Emission Spectrometers for OEMs) optimized for SEMICON applications including plasma monitoring/end-point detection and reflectometry (with the addition of a flash lamp). The OES-Star features unmatched throughput and SNR, spectral coverage and < 1 nm resolution). Our new OES Family, OES-Star, VS70-MC and InVizU all include our latest “Multi-Communications interface” electronics (MC= EtherCAT, Ethernet, USB-2). The Invizu integrates both a linear CMOS sensor for UV-VIS and a TE-Cooled INGAAS sensor, which extends the spectral coverage to 1700 nm.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
Water-cooled Light & Weather Fastness Tester
TF422
-
TESTEX Testing Equipment Systems Ltd.
Xenon Lamp Weather Resistance Test Chamber, to determine the color fastness, aging resistance of textiles, plastics, rubber products or materials by objecting to the simulated conditions of nature weather (daylight, rain, temperature and humidity, etc.). Water-cooled Light Fastness Tester complies with ISO105 – B02 / B04 / 06, AATCC 16, AATCC 169, etc.
-
Product
Reflection Meter
RC-088
-
This instrument is a special equipment for measuring the reflectivity of rearview mirror (or similar product) of motor vehicle. The product composes intelligent measuring instruments, optical integrating sphere, parallel lamp, standard light source, constant current source etc. It is easy to operate，it can measure the reflectivity quickly and accurately. On instrument structure, it adopts standardized modulation design. It takes latest single chip as its digital central processing element. After the measuring signal is converted by modulus, CPU will do some computation and compensation. The instrument can display the reflectivity of device which is measured in rear time. It operates simply and quickly, the indication is direct and accurate. It’s good for quality examination &control in the production scene as well as laboratories. This product has the convenience &quick demarcation way, can meet requirement of different occasion. It is applicable for measuring light reflection on mirror and not mirror parts.
-
Product
Multi Function Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
Live circuit warning LED:Immediate illumination of a warning lamp if the circuit under test is live Auto Discharge:Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing Integral overload protection on internal continuity and insulation test circuitry Autoranging 500V DC test voltage for insulation tests 200mA short circuit current on continuity ranges Loop and RCD Testing Wiring connection check LED''s:Immediate indication if wiring of circuit under test is correct Overheat Protection:Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement Supply Voltage Indication:Can display supply voltage value in loop impedance mode Low Current Loop Impedance Test:Short duration low test current will prevent tripping of many passive RCDs
-
Product
Light Intensity Meter
MT-4617
-
Measures the visible light produced by fluorescent lamp, metal-halide lamp, high voltage sodium lamp or electric incandescent lampBuilt-in precision photo diode sensor and color correction filterAutomatic and manual measured range switchingRelative and peak value measurementMeasures up to 200,000 lux / 20,000 FCExtra functions: Max./Min. value displayOver load indication/Low battery indicationAuto power offBacklightData hold, Zero calibration
-
Product
Digital Torsion Meter
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital Torsion Meter: Fixed with clamp, rotation the lamp the positive and negative torque rate will be record Torque range: 0-10N.m
-
Product
Low-Voltage Twin-Lead Tester
69134
-
Tests 5-50 volt, AC or DC circuits and components.Built-in lamp glows if circuit is live.Each of the 4-1/2'' (114 mm) test leads has an alligator clip on the end.Handy pocket clip.
