-
Product
IV Curve Tracer
IVCT
-
In recent years, we have been developing a sophisticated IV curve tracer for PV modules including a maximum power point tracking (MPPT) function. The IV curve tracer is designed for operation with any market-available steady-state solar simulator. Through our web-based software design, the operator can supervise the test results from every computer in a company network. The software contains functions such as an irradiation sum counter that helps to check requirements stated in a stabilization test like they are defined in IEC 61215 (MQT 19). We have also included a correction function to correct the traced IV curves to standard test conditions (STC) when the user enters the required temperature coefficients. One of the most important features is the multi-IV curve tracing function, which enables the user to display more than 150 IV curves in one graph. This eases the analysis of the weakest cells in hot-spot tests, which are required in IEC 61730 (MST 22) and IEC 61215 (MQT 09).
-
Product
Automated Digital Ground Continuity Tester
-
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
Product
IEC60884 Fig8 Plug Strength Compression Tester
IEC60884 fig8
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig8 plug strength compression testerConforms to the standard: GB2099-1-2008 Articles 10.1 and 24.5 and Figure 8, IEC60884-1 Figure 8
-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Single-Phase Meter Test Equipment
ASTEL 1.2 TYPE
-
ASTeL 1.2 meter test equipment is a fully automatic system that enables simultaneous, multi-position calibration and verification of single-phase electric energy meters. ASTeL 1.2 offers full compatibility with IEC 60736. Thanks to excellent parameters, superior functionality and outstanding flexibility, ASTeL 1.2 is an ideal solution for utility companies, energy meter manufacturers, governmental institutes of metrology, metrological laboratories, and other customers interested in electricity meters testing.
-
Product
Value-added Module With 4 Terminal Block 4-wire Isolated RS-232/422/485
VAM100
-
*4 4-wire Isolated RS-232/422/485*Swappable modular design*Maximize I/O flexibility*2kV isolated protection*Designed for tBOX300/500 series*LVD, FCC, EN 50155 and IEC 60945 certified; CE compliant
-
Product
2.0J Impact Hammer
CX-T20
-
Shenzhen Chuangxin Instruments Co., Ltd.
Required by many Standards to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC, EN, UL, CSA and other international Standards.
-
Product
Vessel For Testing Bob Elements
IEC60335-2-6 Figure101
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-6 Figure 101 Aluminium Test Vessels also conforms to the clause 3.1.9.108 of IEC60335-2-9.The IEC60335-2-6 Figure 101 Aluminium Test Vessels is made of unpolished commercial quality aluminium.
-
Product
Earth Resistance Meter
EM 4058
-
earth tester is a digital, microprocessor controlled instrument that allows to measure the earth resistance and ground resistivity (using Wenner´s method), as well as to detect parasitic voltages present in the ground. This instrument is suitable to measure earth systems in power substations, industries, distribution networks, etc., according to IEC 61557-5.
-
Product
Lightning Surge Generator
SKS-0506IA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0506IA fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 6kV; both AC and DC samples can be tested. The rated voltage of the equipment under test can reach 380V, and the rated current can reach 32A; 7-inch color LCD touch screen, friendly human-computer interaction interface, higher intelligence and more user-friendly operation; the software is built with the level specified by the IEC standard Mode, can be called directly.
-
Product
20KV 30KV Electrostatic Discharge Generator ESD
ESD-202AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performan
-
Product
Fingernail Test Probe
CX-Z11
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Fingernail Test Probe is used to test to IEC 60335 and UL standards. It checks the security of parts that snap together. The spring loading in the handle can be calibrated to the force necessary to use the instrument. This probe is made of stainless steel with specially hardened tip and a Delrin?handle. Handle has a threaded hole for use with force gauges.
-
Product
AC Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
Product
Plug Pin Durability Test Device
IEC60884 Fig30
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig30 plug pin durability test deviceSuitable for checking the tightness of the plug pin,Check the tightness of the plug pin according to the standard, and customize the pin hole gauge of other national standards.
-
Product
Lamp caps gauges
IEC60061
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60061 Lamp caps gauges Quick Details Place of Origin: China (Mainland) Brand Name: CX Reference Standard:IEC60061-3 .
-
Product
Steady-state Solar Simulator For PV Modules
SORAS LS
-
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
Product
Electrical Button Life Span Tester
IEC60884
-
Shenzhen Autostrong Instrument Co., Ltd.
Plugs and the sockets life tester is designed according to the corresponding provisions of the GB2099-96,GB16915-97 and IEC60884-1,used to detect the mechanical life test of the household and similar purposes of the plugs and the sockets products.
-
Product
IEC60884 Fig38 Thermal Compression Test Device For Plug Testing
IEC60884 fig38
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
Product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
Product
Coupling Decoupling Network
TBCDN-M3
-
The TBCDN-M3 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
MCB Instantaneous Trip Test Bench
-
The SCR Elektroniks MCB Instantaneous Trip Test Bench is designed for Testing of MCB to carry out “Test of Instantaneous Tripping and of correct opening of the Contacts” as per IEC: 60898-1:2002 Clause 9.10.2 at rated voltage. This test is carried out with power factor between 0.95 and 1 with the sequence operation being O-t-CO-t-CO-t-CO with timings as specified in 9.12.11.1.
-
Product
IEC Standard Burden Sets (Current)
IEC Burden Sets
-
Testing and calibrating current transformers often requires standard burdens of reliable accuracy and stability, and burdens that are immune to stray fields and harmonics. These burden sets have been carefully designed to meet these requirements. They also provide the standard burdens required for the testing of current transformers for metering service, and for the testing (within the current rating provided by the sets) of current transformers for relaying applications, all as called for by IEC (International Electrotechnical Commission) Publication 185: 1987.
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
Vertically Falling Water Drops Device IPX1/2
IEC60529
-
Shenzhen Chuangxin Instruments Co., Ltd.
This device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005.Satisfying requirements of level IPX1/2. Applide to test LED lamps and house hold appliances, and other electric and electronic products waterproof test of IP code level IPX 1/2.
-
Product
Digital Network Analyzer
F6880
-
The Doble F6880 Digital Network Analyzer (DNA) reveals details that are essential to helping protection engineers and relay test technicians quickly resolve issues in IEC 61850 network traffic.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Interferometers
-
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
