Sensor Testers
-
Product
Measurement, Communications & Testing
-
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
Product
Oxygen Sensor Tester And Simulator
7650
-
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
ADB Bearing Sensor Tester
-
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
Product
Image Sensor Test System
IP750
Test System
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
Product
Portable RF Analyzer
PMT-330
-
The Process Sensors Portable Moisture Tester (PMT-330) puts the capabilities of an on-line moisture analysis and control system into the palm of your hand, allowing operators to spot-check moisture content of boards, wood, plastic, and paper products quickly and easily. It features radio frequency dielectric (RF) measurement technology that penetrates the surface of products and instantly displays accurate moisture data.
-
Product
AMIDA 2020XP Tester
-
AMIDA 2020XP CIS tester is the latest generation of CMOS image sensor-specific measuring instruments from Metatech. In addition to the original true and accurate measurement, the high-throughput mass production solution designed for the high-throughput inspection of image lens modules and camera lenses has been well received after nearly 20 years of mass production experience. First-class factories at home and abroad import production. AMIDA 2020XP CIS testing machine not only meets the customer's testing time and high output and accuracy requirements. Within the range of functional flexibility, users can customize their measurement requirements according to the definition of various sensors. AMIDA 2020XP CIS tester is a new generation of CMOS Image Sensor dedicated tester, which integrates DC open/short/leakage test, AC Pattern test and image test. It uses 180 Pin high-speed cable to connect to the test end
-
Product
Image Sensor/Fingerprint-on-Display Testing
-
Enli Tech provides the most advanced optical and non-destructive inspection technology, which can de-convolute the digital images back to the analog properties, such as quantum efficiency, spectral response, system gain K, Dynamic Range (DR), PRNU, DRNU, Linearity Error LE, and Chief-Ray-Angle (CRA). The testing solution can be applied to CCD and CMOS image sensors in aerospace, defense, and scientific camera field. Image sensor packages that can be tested by Enli Tech’s systems include bare wafers, dies, chips, or camera modules. Our image sensor testers can help users reduce the sensor-modules or camera-modules development time and RD budget.
-
Product
Sensor Tester
QST-5
-
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
DC/10 MHz 67 GHz USB Thermocouple Power Sensor
U8488A
Power Sensor
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
Product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9321A
Power Sensor
The E9321A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
-
Product
E-Series Average Power Sensor
E9300H
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -50 dBm to +30 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Waveguide Power Sensor
R8486D
Power Sensor
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 26.5 GHz to 40 GHz Diode power sensing element
-
Product
Power Sensor
8483A
Power Sensor
The 8483A diode power sensor measures average power over the frequency range 100 kHz to 2 GHz and power range -30 to +20 dBm (50 dB dynamic range).
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
10 MHz to 33 GHz LAN Wide Dynamic Range Average Power Sensor
L2053XA
Power Sensor
The Keysight L2053XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz LAN average power sensor.
-
Product
Thermocouple Power Sensors
N8487A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
10 MHz – 6 GHz USB Power Sensor
U2001B
Power Sensor
U2001B USB power sensor measures average power over the frequency range 10 MHz to 6 GHz and power range -30 dBm to +44 dBm.
-
Product
S2 Unicolor Sensors
ULP-S2 SCI/V
LED Sensor
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
2.4/5GHz Wi-Fi Temperature And Humidity Sensing Module
WISE-4250-S232
Environmental Sensor
Supports IEEE 802.11 ac (2.4GHz/5GHz) for stable and high-speed wireless connectivityEnsures secure data transmission with WPA3/TLS 1.3 encryption and X.509 certificate authenticationProvides seamless cloud integration, supporting MQTT and RESTful API to upload temperature and humidity data to cloud platforms such as AWS, Azure, SCADA, and WebAccessOffers comprehensive protocol support, including MQTT, Modbus/TCP, SNTP, TCP/IP, HTTPS, RESTful, UDP, and DHCPFeatures a built-in watchdog timer to maintain continuous operation and automatically recover from disconnectionsWith UDP-based AES-128 encrypted wireless P2P, abnormal inputs can automatically trigger up to 16 WISE modules in the field
-
Product
Diode Power Sensor
8487D
Power Sensor
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
Product
10 MHz - 18 GHz USB Power Sensor
U2000A
Power Sensor
U2000-series USB Average Power Sensor enable fast, simple setup by providing plug-and-play USB connectivity and by eliminating the need for a separate power meter.
-
Product
Waveguide Power Sensor
Q8486D
Power Sensor
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 33 GHz to 50 GHz Diode power sensing element
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
Balance Thermocouple Power Sensor, DC To 50 GHz
N8487S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
LoRaWAN® Enabled Temperature And Humidity Sensor
EVA-2310
Temperature Sensor
LoRaWAN® wireless connectivity-20 °C to 55 °C temperature detection range0%RH to 90%RH humidity detection rangeBattery life up till 5 years@25 °C, 15 mins interval settingEasy to deploy and maintain
