Injectors
Introduce known values.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
POWER PROBE 4
PP401
-
*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)
-
Product
Power over Ethernet
PoE Tester
-
Covering both commercial and industrial applications, PLANET Power over Ethernet (PoE) products offer highly-dependable power and data transmission. Featuring 802.3bt standards, intuitive touch LCD design, Long Reach PoE technology over fiber optic cabling, coaxial cabling or UTP cabling, and PLANET exclusive intelligent PoE Management functions, all the requirements can be met for such applications as IP surveillance, IP communications, POS systems, PoE lighting and more. Our full range of PoE product lines include 95W 802.3bt PoE++/ 30W 802.3at PoE+ Managed Switches, Industrial flat-type PoE+ Switches, PoE Injectors, Splitters, Extenders designed for both indoor and outdoor environments.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
Fuel Pressure Testers
-
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
PRO Test Lead Kit
142
-
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
Product
Pro Model Automotive Meter W/PC Interface
595
-
The #595 is a premier automotive diagnostic tool. It is equipped with the latest testing capabilities, including Milliseconds Pulse Width, for measuring the on-time of fuel injectors. The #595 features a huge LCD display w/bargraph for easy viewing. This meter can even be interfaced to your PC or notebook computer for enhanced diagnostics and data presentation. The software and computer interface cable are included free! The #595 includes two sets of test leads, RPM pick-up, temperature probe, software CD, interface cable, protective holster, 9 volt battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
Product
DC Bias Injector
J2130A
-
When using the network analyzer to measure impedance, such as the capacitance and ESR or a capacitor, or the DCR of an inductor, etc., it is often necessary to provide a voltage bias to the device being tested. This is true of semiconductor junction capacitances, varactors, and some ceramic capacitors (especially X5R). In these cases the impedance is a function of the DC bias on the device. The Picotest DC bias injector (J2130A) is used for this purpose during impedance measurements.
-
Product
EFI Test Light-Bosch 2
3416
-
Peaceful Thriving Enterprise Co Ltd
Simply for testing: Disconnect the fuel injectors, plug in a Noid. Quickly determines if the electrical signal present at the fuel injectors. Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
Product
Premium Automotive DMM
597
-
*CATIII 1000 Volt / CATIV 600 Volt Approved & Safety Rated *Safe For Use on Hybrids and EV's *Highest Quality Auto-Ranging DMM Designed for Automotive Trouble Shooting *18 Test Functions, 48 Test Ranges *Peak Min/Max records transient voltages as fast as 1 millisecond *Min/Max Mode records variations in all functions *Also measures Temperature via Temp Probe in Both F and C *Milliseconds Pulse Width Measures Fuel Injector ON-TIME *Inductive RPM Readings for both DIS and Conventional Ignitions *Desirable 20 Amp Test Range - Dual Fuse Protection *Modern Design, the Protective Holster is Built Into the Housing *Data Hold, Auto Power-Off, + Trigger Adjust *Large LCD Display w/White LED Backlighting and 40 Segment Analog Bargraph *Blow Mold Case, Test Leads, K-Type Temp Probe, Inductive RPM Clamp and Instructions included *Waterproof to IP67 Standards
-
Product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
Analyzer
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.
-
Product
FUEL INJECTOR CANISTER CLEANER
FIT470B
-
*Cleans carbon from intake valves, fuel passages and cylinders with a professional carbon cleaning solution*Will restore the original spray pattern more effectively, giving improved performance, fuel economy and emission tests*Uses shop air with any professional canister cleaning solution on the market
-
Product
Automotive Test Lead Kit
143
-
Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
-
Product
Electrical Testers
-
Actron is an industry leader in electrical testers for your car or home repair projects. Pick your choice of Actron’s digital multimeters to help pinpoint problem areas and determine which components need repair or replacement. Find shorted and open wiring with the help of our circuit testers. Troubleshoot fuel injectors, solenoids, and digital sensors with the Actron Automotive Logic Tester. Use Actron IR thermometers to check AC systems, brakes, catalytic converters, cylinder heads, and overheating electrical components. Use the Actron Videoscope to inspect hard to reach areas. Measure and set spark plug timing on older vehicles, tractors, lawn mowers and more using Actron timing lights. Find bad batteries and faulty charging systems with Actron Battery Load Testers. Our Remote Starter Switches allow one person to conduct tests while cranking or starting the engine.
-
Product
Low Current Probe/DMM
687
-
With the capability of measuring down to 1 milliamp (.001A), the #687 is a great tool for all low current applications. Especially for diagnosing parasitic drains! Clamp opening is large enough to fit over most negative battery cables. Applications: fuel injectors, fuel pumps, electric motors, battery drains, charging systems.
-
Product
Solid State Current Injector
J2111A
-
The current injector is one of the most versatile of the injector products. Coupled with the G5100A, or other equivalent function generator, it is capable of performing small signal load steps up to 40MHz, with very fast rising and falling edges. Using the G5100A, also allows the rise and fall times to be controlled, various waveforms or even arbitrary waveforms. This can be used to simulate the effects of many different types of loads, including high speed digital circuit loading, which is often largely dynamic.
-
Product
Thermal Desorption
-
Scientific Instrument Services, Inc.
The SIS Short Path Thermal Desorption units sit directly on top of a GC injection port to provide for the direct desorption of both volatile and semi-volatile samples into the GC injection port and column. Due to the "short path" of sample flow, these new systems overcome the shortcomings of previous desorption systems by eliminating transfer lines, which are easily contaminated by samples, and by providing for the optimum delivery of samples to the GC injector via the shortest path possible--the direct, syringe-like injection into the GC.
-
Product
Line Injector
J2120A
-
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
Product
Low Temperature Gas Source
-
Get a low-cost means to introduce a gas without thermal pre-cracking using Veeco’s low-temperature gas source for molecular beam epitaxy (MBE) systems. The source features a large conductance tube for fast gas switching and a diffuser end plate for good growth uniformity. It is an ideal gas injector for CBr4 for carbon doping in GaAs and NH3 for GaN growth, as well as any other gases that do not require thermal pre-cracking. Enhance system capabilities further by combining the source on one mounting flange with an Atomic Hydrogen Source or 5cc Dopant Source.
-
Product
Interface Cards / PoE Injector
-
Gigabit Ethernet with PoE allows for single cable camera solutions, simplifying installation and maintenance. For those who will be externally powering the camera we offer a single port Gigabit Ethernet card and a PoE injector unit.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
Engine Controller
FireLynx
-
The fully programmable FireLynx control module is used for Engine Development, Test and Control as well as directing the real time operation of Fuel Injector Test Stands.
-
Product
Professional Automotive DMM
590
-
Another good choice for the professional automotive technician, the #590 puts the right cababilies in your hands. For example, the #590 can test the on-time of fuel injectors using the Ms pulse width test function. This DMM is completely auto-ranging, making it an easy and efficient tool to use. The #590 includes two sets of test leads, RPM pick-up, temperature probe, 9 volt battery, instructions manual and carrying case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
Product
Common Rail Injector Tester
ICR-4 Tester
-
ICR-4 tester is used to control electromagnetic and piezoelectric injectors used in the common rail injection systems. It is possible to control up to four injectors of a type at a time. The signal generated by the tester which controls the injectors, corresponds to the signal which appears in the car engine controller.
-
Product
USB Harmonic Comb Injector
J2150A
-
The USB Harmonic Comb Injector is a fast, easy-to-use, ultra-portable signal generator for interrogating your PDN to identify noise sensitivities. Quickly identify power supply related issues. Multiple modes include time and frequency jitter. Wideband harmonic comb spans 1kHz-1GHz+. Great for clock power supply EMI spectrum testing.
-
Product
PoE Injectors, Splitters and Extenders
-
Advantech's fiber & PoE converters, injectors, splitters, and extenders are designed to provide network operators support for Mega PoE IEEE 802.3BT
-
Product
Injector Tester
7620A
-
Peaceful Thriving Enterprise Co Ltd
By connecting with the 12V battery, the tester generates four different output signal pulses for user to check the condition of the injector. By using the tester, user can check if the injector is clogged, leaking, or blasting. By selecting the continuous pulse, user can also use this test to help clean the injector.
-
Product
Fiber Optic Measurement Systems & Sensors
-
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
Product
EFI Test Light-GEO TBI
3413
-
Peaceful Thriving Enterprise Co Ltd
*Simply for testing: Disconnect the fuel injectors, plug in a Noid.*Quickly determines if the electrical signal present at the fuel injectors.*Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
