ISO
International Standards Organization
-
Product
Magnetic Stripe Test Cards
-
Test Limit Cards (and tickets) are nominally encoded to ISO standards BUT WITH specific parameters deliberately set to predetermined levels, which can be inside or outside the ISO limits. The Test Limit Cards are designed for use by Test\Inspection Departments, Field Service Engineers, Reader \ Encoder Development Engineers to check and confirm proper operation of magnetic stripe reading equipment (e.g. ATMs and POS).
-
Product
Weather Antennas
-
Kratos Defense & Security Solutions, Inc.
The S- band and C- band weather radar systems are a family of advanced weather radar antenna/pedestal systems. The family of systems meets ISO 9001 specifications and consists of a number of different diameter antennas and pedestals operating in S- band or C- band frequencies. This includes the antenna system used for the NEXRAD program.
-
Product
Melt Flow Testers
-
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
Product
Labratory Micro-Spot XRD Residual Stress Analysus with both Iso- and Side-Inclination Methods
AutoMATE II
-
Residual stress may be created during the manufacturing process of a material, or it may accumulate in a structure over many years in operation. In either case, this stress can have a serious negative effect on a product's quality, durability and lifetime. Accurate detection of residual stress is an important element of the quality control process and helps predict the service lifetime of products.
-
Product
Spectrally Flat Class B Pyranometer
LPPYRA02… Series
-
Spectrally Flat Class B (First Class) pyranometer according to ISO 9060:2018. The LPPYRA02 are well suited for the measurement of incoming global solar radiation (0.3μm…3μm spectral range). Complete with: shade disk, sachet with silica-gel crystals, 2 cartridges, levelling device and calibration report.
-
Product
ISO/ANSI Compliance
-
The ANSI and ISO/IEC standard for the C Programming Language specifies that there are two forms of conforming compiler implementations: hosted and freestanding.
-
Product
SuperGuard C Library Safety Qualification Suite
-
The SuperGuard C Library Safety Qualification Suite is a requirements-based test suite for the C standard library with full traceability between the requirements derived from the ISO C language definition and the individual library tests. It is designed to support the qualification of implementations of the C standard library for safety-critical applications, both for third-party (COTS) and for self-developed or maintained C library implementations.
-
Product
Paper Softness Tester ZRD-T1
-
The ZRD-T1 Paper Softness Tester is a device designed to objectively measure the softness of paper products, such as tissues, toilet paper, or specialty papers. Softness is a complex tactile property influenced by factors like surface smoothness, flexibility, and bulk compressibility. It is widely used in industries such as tissue manufacturing, hygiene product development, textiles, and packaging to ensure compliance with quality standards and end-user comfort requirements. This test instrument conforms to many national and international standards: ASTM D2923: Standard Test Method for Rigidity of Paper – Measures bending resistance to determine stiffness. ASTM D6828: Standard Test Method for Stiffness of Nonwoven Fabrics – Evaluates drape and flexibility in materials like medical textiles or wipes. TAPPI T498: Bending Resistance of Paper (Gurley Method) – Quantifies resistance to bending forces, inversely related to softness. GB/T 8942: Chinese Standard for Softness Testing of Household Paper – Aligns with consumer expectations for tissue and toilet paper tactile quality. ISO 12625-9: Softness Evaluation of Tissue Products (optional add-on).
-
Product
Nuclear Magnetic Resonance Equipment
SpecFIT HR50
-
Low-field Nuclear Magnetic Resonance (TD-NMR) equipment with easy-to-use software and certified analysis (ISO, AOCS, etc.).
-
Product
One-Touch, Strain Gauge Extensometers
SSG-H Series
-
The SSG-H series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards for hard plastics and metal materials Featuring a wide elongation measurement range with the ability to measure using small gauge lengths, these lightweight, clip-on strain gauge extensometers attach to both rod and flat plate specimens.
-
Product
Additional Rotary Axis for High Precision Co-ordinate Measurement Machines, ISO 10360 Part 3 Compliant
QuadDualPurpose
-
Rotary Precision Instruments UK Ltd
Precision rotary axes specifically developed to increase the flexibility, productivity and efficiency of your CMM.Versatile system with the option to mount parts both horizontally and vertically for inspection, such as large turbine blades from the front of the engine.
-
Product
Static Axial Clip-On Extensionmeters
2630-100 Series
-
The Instron static axial clip-on extensometer delivers precise strain measurement for static tests by quickly clipping to specimens (metals, plastics, composites) with minimal attachment force. Its rugged cross-brace design resists distortion, includes built-in over-extension protection, and meets ASTM E83 / ISO 9513 standards — making it a reliable, high-accuracy option for general and temperature-controlled testing.
-
Product
Between Bearings Pumps
-
Flowserve between-bearing pumps comply either with ISO, ASME or API standards. These pumps are available in a variety of designs like single or double case, axially or radially split with single-stage or multistage impeller. These configurations guarantee reliable and efficient pumping processes. Numerous sizes, hydraulics and material combinations are particularly well suited for use in applications where uncompromising reliability and efficiency over a wide flow range are key.
-
Product
Antenna Calibration
-
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Product
SOLUBLE SALT TESTER
-
The PosiTector SST Soluble Salt Tester measures the concentration of soluble salts (salt contamination) on metal surfaces in accordance with ISO 8502-6, 8502-9. View Video
-
Product
Electronic Crockmeter
TF411
-
TESTEX Testing Equipment Systems Ltd.
Crockmeter, to determine the colour fastness of textiles to dry or wet rubbing. Electronic Crockmeter complies with ISO 105×12/D02, AATCC 8/165, BS 1006-D02, etc. Crockmeter is useful in crockmeter test and Crockmeter price is competitive.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
Software
Online Tool Calibration
-
GageList is the simple online calibration management software solution that makes maintaining tool calibration records easy and economical. Trusted by major global industries, GageList supports compliance with ISO 9001, ISO 14001, API Q1, AS 9100 and other standards.
-
Product
Evaluation Services
-
Atlas Material Testing Solutions
Atlas offers a wide range of evaluation and measurement services for our client's specimens during and after the weathering process. These services are available at Atlas' Miami, Florida and Phoenix, Arizona sites. Atlas uses the most advanced instrumentation from leading manufacturers for measuring appearance properties such as color change, gloss, distinctness-of-image, transmittance and reflectance. All of our services meet the latest measurement test standards from organizations such as ASTM, ISO, DIN and others. A full range of visual assessment services is also available, including coating adhesion, blistering, chalking, cracking, mildew growth, and gray scale evaluation in accordance with respective standards' organizations. Temperature monitoring programs are provided for single and multiple specimens under any type of exposure, as well as for large assemblies such as complete vehicles. Strict quality control guidelines have enabled Atlas' Evaluations Laboratory to achieve industry-accepted accreditation from world renowned standards' organizations. Atlas is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) and accredited or approved by Ford, GM and AMECA.
-
Product
Novo-Gloss Trio Glossmeter 20/60/85
-
20/60/85 glossmeter for measuring matt to mirror finishes. Complies to ISO 2813 and ASTM D523. Supplied with 2 year warranty, NIST traceable calibration tile
-
Product
System
SYS-24
-
The system shown here was built for a customer to be used in metallization, a common use for many smaller systems. It is also fully capable of performing optical coatings when equipped to do so. This particular system came equipped with a 16" APD ISO Flange mounted cyropump, and a Varian tri-scroll for roughing. The cooling tubes for the crystals as well as the drive motor for the parts holder can be seen on the top of the chamber.
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
Product
Tribometers/Abrasion Testers
-
AEP Technology offers several ASTM, ISO DIN compliant friction and wear tester models optimized for various applications. The modular design allows it to run on one platform (rotary, linear reciprocating, linear, block-to-ring, etc.), and to ensure high repeatability, during the testing process our downward force friction and wear testing machine controls several standard tests. High-end electronics, multi-core 64-bit processor that allows it to use multiple in-situ sensing technologies (recording friction, wear, displacement, force, volume, temperature, humidity, position, speed, etc., during testing) with high resolution Embedded powerful platform imaging head (sections of atomic force microscopes, etc.). Ease of use and robust unique design make AEP Technology a powerful tool in friction and wear testing machine development and production environments.
-
Product
ContactLAB Spy
-
Laboratory class spy and protocol analyzer for easy, non-intrusive capture and analysis of communication between contact cards and readers using SWP, ISO 7816, SPI and I2C protocols.
-
Product
Hydrostatic Head Tester
-
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
Product
Band Pass Filters
-
*High power handling 200W with a wide range of bands available*Excellent Isolation with Low Intermodulation*High reliability of >500K Hours MTBF and multi-strike lightning protection*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Light Meter Calibration Services
-
International Light Technologies
International Light has been offering light meter calibration services since we created the first USA-made light measurement system in 1965. Our full service calibration lab offers ISO 17025 Accredited (UKAS recognized) calibrations and certifications that are also N.I.S.T. Traceable.
-
Product
Package Testing
-
Lansmont package testing equipment is designed to perform industry standards, such as ASTM, ISTA, ISO, EUMOS and others. Our equipment is compliant with all of the most common ASTM and ISTA package testing procedures. There are individual standards that specifically reference how to perform drop testing, compression testing, side impact testing and vibration testing. In addition to those standards, there are groups of procedures referred to as distribution simulation tests, which incorporate some strategic combination of testing inputs, with the idea of simulating a typical journey through the supply chain. Some of the most common distribution simulation standards that are performed globally are published by ASTM and ISTA.
-
Product
Calorific Value Calculation Software
-
The Calorific Calculation Software can automatically calculate calorific values and generate reports that comply with BTU and ISO 6976. In addition, the target gas can be registered according to the customer’s requirement.
