Timing Generators
-
product
Digital/Pattern/PE Card
PE16S
The PE16S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE16, the PE16S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (16 boards). The PE16S offers 16 programmable level input or output channels with 2 PMU . The PE16S also supports deep pattern memory by offering 32 M of on-board vector memory with per channel dynamic direction control running test rates up to 66 MHz.
-
product
TCSPC Lifetime Fluorometer
DeltaFlex
The DeltaFlex time correlated single photon counting (TCSPC) system is one of our Delta series of next generation time correlated single photon counting lifetime instrumentation. The DeltaFlex offers the ultimate in flexibility.
-
product
Dual Channel Multi-function Decommutator
LS-55-DD
The Lumistar LS-55-DD PCI Dual Multi-function PCM Decommutator offers two multifunction decoms and two optional bit synchronizers (LS-45) in a single PCI card slot. The multi-function decoms are implemented in FPGA using a next generation design based on the LS-50-P. The simulators,decommutators, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through a low-profile daughterboard. CVSD voice, h.261 video, and IRIG Chapter 8 decoding are achieved through software.
-
product
Time Synchronization Card
PMC/XMC
IXI Technology’s highly-accurate card provides time down to 62.5ns resolution in UNIX format. Its time-sourced, disciplined, voltage-controlled crystal oscillator (VCXO) or optional CSAC not only allows it to provide sub-second resolution, but also to “flywheel” during the absence or loss of carrier. The module has a status LED that indicates when the internal time is synchronized with the input time code. The card provides a programmable offset on its internal time from the input time source. The generated IRIG-B or 1588 output can be configured to be synchronous to the chosen input time source or configured to use the best available time source.
-
product
IRIG-B Analyzer/Generator
APP-110
Battery powered• 3.5” backlit touchscreen display• Oscilloscope view• IRIG-B time signal decoder and analyzer• IRIG-B/1PPS time signal generator
-
product
LXI WTB Terminator, 100 ohm
60-983-001
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
-
product
DC Power Supplies
Is the unidirectional flow or movement of electric charge carriers (which are usually electrons). The intensity of the current can vary with time, but the general direction of movement stays the same at all times. As an adjective, the term DC is used in reference to voltage whose polarity never reverses.
-
product
Linear Array
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
-
product
Central Office Line Simulator
AI-7280
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
product
10 Gb/s Programmable Digital Delay Line
PDDL10
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
product
5 Gb/s Programmable Digital Delay Line
QPDDL5
The QPDDL5 series delay lines are four channel precision time delay generators for digital signals. Delays are controlled precisely in 5 or 10 ps increments at data rates up to 5 billion bits per second or clock rates exceeding 2.5 GHz. Each of the four channels is independently programmable.
-
product
Digital/Pattern/PE Card
PA32S
The PA32S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PA32S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32S also supports deep pattern memory by offering= 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 33 MHz. With new 32M capture/log memory, PA32S can capture 32 channels fail log.
-
product
2nd Generation PCIe Multi-function Decommutator
LS-50-E
The Lumistar LS-50-E PCIe Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCIe card slot. The multi-function decom and simulator is implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profiledaughterboard. CVSD voice decoding, h.261 videodecoding, and IRIG Chapter 8 decoding are achievedthrough software.
-
product
200 MS/s Waveform Generator & Dual 50 MHz Pulse/ Timing Generator
3172
The Racal Instruments™ 3172, a 200 MS/s Waveform Generator and Dual 50 MHz Pulse and Timing Generator, combines multi-instrument density and highfrequency performance in a single-slot, C-sized VXIbus format.Waveform output in the range of 100 μHz to 30 MHz with 16-bit vertical resolution (12-bit vertical for 3171 emulation) and pulse output to 50 MHz make the 3172 a powerful solution to a variety of test stimulus requirements.
-
product
Compact PCI Multi-function Decommutator
LS-50-cP
The Lumistar LS-50-cP 3U Compact PCI Multi-function PCM Decommutator offers the greatest flexibility in the industry by incorporating up to 10 functions typically encountered in flight test applications in a single 3U Compact-PCI card slot. Five functions are achieved on the main board (PCM Simulator which can also operate as a BERT, PCM Decommutator, IRIG Time CodeReader, IRIG Time Code Generator, and the same 5 functions can be achieved on the LS-55-DB Multi-Function Decom Daughterboard. CVSD Voice Decoding and h.261 Video Decoding are achieved through software.
-
product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
LXI WTB Terminator, 90.6 ohm
60-983-002
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Transition Time Converter, 500ps
15433B
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
product
Transition Time Converter, 250ps
15432B
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
product
Digital Pulser
HH2602
Handy, Quick and Easy to use tool. Accurate time base generator. 9 seleclable frequency puise output. LED opersation indication. Open collector output. Compact for in-circult trouble shooting. Size: 180mm x 30mm x 20mm
-
product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
product
Intelligent Time Reference
TM-4™and TM-4/OEM™
The Intelligent Reference/TM-4™ and TM4/OEM™ are multi- purpose, GPS disciplined timing signal generators and frequency references in economical off-the-shelf and custom configurations. Intended for use in a wide variety of timing, synchronization and frequency reference applications, they are based on the most advanced architecture Spectrum has ever offered, and include the most popular features of Spectrum's core platform for current timing products.
-
product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
product
Clock And Timing
Achieving highly accurate precision timing is no easy feat from a technology perspective, so it’s important to find a resource you can trust to reduce design risk and speed your time to market. Our end-to-end timing solutions generate, distribute and apply precise time for multiple industries, including communications, aerospace and defense, IT infrastructure, financial services, power utilities and more. We provide a broad range of clock and timing solutions ranging from MEMS oscillators to active hydrogen masers. Explore our portfolio of clock and timing components and systems to find the right solution for your project.
-
product
GPS NTP Time Server - SYNTIME
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when synchronized with time sources. It is a sleek, rack-mountable unit that synchronizes and maintains equipment/device time and avoiding any time drifts due to local RTCs. NTP output from time server supports unicast, broadcast, and multicast methods based on selection and behaves like a reference clock for the network. Apart from time synchronization protocols, it supports MD5 (Security key), SNMP, SSH, HTTP (Configuration), TELNET, FTP, and SYSLOG. IP address of the LAN ports can be field configurable.
-
product
Video Timing Generator
VTG
The VTG Video Timing Generator provides up to ten video sync signals with which to synchronize CCTV cameras in the field. The VTG is intended to be used with the VTM Video Timing Meter to establish accurate timing of multiple CCTV cameras.
-
product
LXI WTB Terminator, 109.8 ohm
60-983-003
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
5 Gb/s Programmable Digital Delay Line
PDDL5
The PDDL5 is a precision time delay generator for digital signals. Delays are controlled precisely in 5, 10 or 20 ps increments from 0 to 5115, 10,230 or 20,460 ps range respectively. Data rates up to 5 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
product
Digital/Pattern/PE Card
PE32H
The PE32H represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PE32H offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PE32H also supports deep pattern memory by offering 32M of on-board vector memory with dynamic per pin direction control and with test rates up to 66 MHz. With new 32M log memory, PE32H can capture 32 channels data or fail log.
