Optic Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
Optical Loss Test Set/Light Source/Optical Power Meter
-
The CMA5 series (Optical Loss Test Set/Light Source/Optical Power Meter) offer superior accuracy and reliability for evaluating a wide range of optical devices and systems including WDM.
-
Product
Optical Fiber Identifiers
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Optical Fiber Identifiers
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
Product
High Static Stiffness Optical Breadboards
5700 Series
-
They feature a lightweight precision formed steel honeycomb construction with 3/16″ ferromagnetic stainless steel top skin and 3/16″ low carbon steel bottom skin with a black polyurethane finish.
-
Product
Variable Optical Attenuators
5418
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
Fiber Optic Communications
-
Fiber optic converters are installed between the end of fiber optic cables and data loggers to provide a lightning-proof connection.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Fiber Optic Instruments
-
Tempo Communications provides a comprehensive line of fiber optic testing solutions that enable tech... nicians to install, commission, and document P2P and FTTx installations. Accurate troubleshooting is made effortless with the 930XC family of OTDR’s, optical power meters, visual fault locators, and the fiber identifier, while installing fiber has never been easier with the fusion splicer, fiber cleaver, splice on connectors, and fiber hand tools. Elevate your fiber game with Tempo!Show less
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
40mA Multi-Channel Amplifier
-
For the precise nanometer movement of actuators and other piezo products, an amplifier is required. Multi-channel amplifiers allow you to control multiple actuators or piezo products with a single amplifier. The NV40/3 piezo amplifier was designed for controlling low voltage piezo elements. It includes a voltage amplifier, a display and a PC-interface. The high-resolution display shows the voltage of the actuator, along with the mode of operation and the temperature inside the amplifier.
-
Product
Waveform Amplifier 30 Volts Pk-pk
WA301
-
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
Product
X6 Optical Fiber Fusion Splicer
-
Smart-connected APP, Splicing record management, Intelligent burglary-resisting system 1 sec. topspeed boot time, 6 sec. splicing time, 12 secs. Heating time. 3D protection cover reduce risk and unpredictability. Handy, lightweight, anti-dropping solid and durable.Hi-Speed USB connection internet remote control.
-
Product
Automated Optical Inspection
K Series3D
-
K Series and K Series3D are the reference in Automated Optical Inspection (AOI), allowing 2D and 3D inspection with very low false calls rate, for both pre-reflow and post-reflow. They are the most powerful gatekeepers to guarantee high quality level for the assembled PCB.
-
Product
Yamasaki Optical Fiber Identifier
TF916
-
The Yamasaki TF916 Optical Fiber Identifier is an essential part of any professional fiber optic toolkit. By inserting fiber into the Yamasaki TF916 Optical Fiber Identifier head, the Yamasaki TF916 Optical Fiber Identifier can be used to identify traffic, traffic direction, frequency and optical power within any singlemode optical fiber. The sleek black outer housing is comprised of an anodized aluminum to make it lightweight and tough. Also included with the Yamasaki TF916 Optical Fiber Identifier are four adaptor heads that are specifically designed to suit various optical fiber types with minimal bend loss. The easy to read ultra-bright LED display and audible tone make operation easier and can save you valuable time in the field.
-
Product
1211a Optical Receiver/Distribution
-
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, LLC. has now introduced a new Optical Time Code Receiver, with Auto Switching, a full complement of time code outputs, and Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1211A delivers up to thirty six channels of Time Code outputs, including re-transmission of the optical input. The unit can accept a pair of inputs (usually from separate primary and backup sources), and provides monitoring of both the inputs and outputs for signal integrity.If the primary input fails, the unit will automatically switch to the backup input and indicate a primary signal fault.Full remote monitoring and control via RS232 and Ethernet interfaces includes telnet, http (web browser), and SNMP protocols.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
2D Automated Optical Inspection Systems (2D-AOI)
BF1 Series
-
Saki’s unique line scanning technology and coaxial overhead lighting enables high-speed accurate inspection.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-222
Multiplexer Module
The 40/42-860A-222 is a PXI/PXIe dual insert/bypass switch with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
Inline Optical Power Meter - MATRIQ
1600 Series
Power Meter
The Power 1600 Series optical power meter provides quick and accurate inline power monitoring from -50 dBm to +20 dBm with 1, 2 or 4 channels in a compact form factor.
-
Product
Fiber Optic Crank Angle Measurement System
CP-5730/CP-0610/CA-6000B
-
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5730 Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-0610 Rotation stop jig.
-
Product
Amplifier
AC-100
-
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
Product
Free Space Optical Receivers
-
These optical receivers have bandwidths in the DC to GHz range for detecting high speed free space optical signals with the lowest noise and cleanest responses possible.
-
Product
Fiber Optic Circulators
-
Nanning Xionghua Photonics Technology
Fiber Optic Circulators by Xionghua Photonics
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
Glass Sealed Electrolytic Cell With Quartz Optical Window
SWO-1
-
SWO-1 Glass Sealed Electrolytic Cell with Quartz Optical Window is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model.
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-014-M62.5-HI
Multiplexer Module
The 40/42-850A-014-M62.5-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
