Plugs
A male connector.
-
product
Cable Assembly, Receiver, Mini Coax, 36", 4 BNC Plugs
540064010207
Cable Assembly, Receiver, Mini Coax, 36", 4 BNC Plugs
-
product
Cable Assembly, Receiver, 20", Mini Coax, 6 SMB Plugs
540093010107
Cable Assembly, Receiver, 20", Mini Coax, 6 SMB Plugs.
-
product
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36" to 9-Pin DIN, 3 BNC Plugs & 2 SMB Plugs
540096010211
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36" to 9-Pin DIN, 3 BNC Plugs & 2 SMB Plugs
-
product
Cable Assy 78-Pin D-Type Female to 16 x Mini Thermocouple Plugs, 1m
A078DFR-16M002T5A100
This 78-pin D-type thermocouple cable assembly is terminated with 16 male mini thermocouple plugs. It is constructed from 7/0.15 (26AWG) silver plated copper wire and screwlocks are provided to secure the D-type to its associated products.
-
product
Cable Assembly, Receiver, TriPaddle/Micro Coax, 20", 2 9-Pin Female D-Subs, and 2 SMB Plugs
540278010159
Cable Assembly, Receiver, TriPaddle/Micro Coax, 20", 2 9-Pin Female D-Subs, and 2 SMB Plugs.
-
product
Cable Assembly, Receiver, High Frequency, 20", 10 SMA Plugs
540153010112
Cable Assembly, Receiver, High Frequency, 20", 10 SMA Plugs
-
product
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 7 SMA Plugs
540133010253
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 7 SMA Plugs
-
product
Test Block & Plug Systems
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
product
LilyPad Arduino USB
ATmega32U4 Board
This is the LilyPad Arduino USB board, controlled by an ATmega32U4 with the Arduino bootloader. It has a built in power supply socket and an on/off switch with the only extra piece of hardware you need to program the LilyPad USB is a micro-USB cable, since the new IC has built-in USB support. Any of our LiPo batteries can be plugged right into the JST socket to provide you with easy, on-the-go power. That LiPo battery is even rechargeable through the board, no more special external LiPo chargers required!
-
product
Software
SSI-TRES
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
product
Retractable Cable With Magnet Adsorption
3701
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.*Embedd A Magnet on the back to fix on suitable metal sheet of cars easily.
-
product
Data Logger for Ultra Low Temperature
DSR-ULT
Special probe using military industrial technology supports measuring temperature ultra low to -100 Original fittings for sensor connection, ensures 100,000 plugs Support single DSR connecting to PC via USB interface, and multiple DSR grouped in RS485 or LAN networking for central management Suitable for medical refrigerator, biological specimens preservation, scientific research and other applications
-
product
PXI General Purpose 2A Relay Module 32xSPST
40-132-201
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
0 to 1000 ppm CO Measurement Range
EL-USB-CO
The EL-USB-CO is a USB data logger that measures and stores up to 32,510 Carbon Monoxide (CO) readings over a 0 to 1000 ppm measurement range. The user can easily set up the logging rate and start time, and download the stored data by plugging the module straight into a PC's USB port and running the purpose designed software under Windows 2000, XP or Vista
-
product
50Ω UWave SMA Cable Assembly, 26.5GHz, 0.25m
40-977-542-0.25m
50 Ohm uWave SMA Plug to uWave SMA Plug Cable Assy, 26.5GHz, 0.25m Long.
-
product
LIGHT RANGER MUTT
TT9103
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
product
Cble Assmbly Ins Push-On F To RJ45 Plug
#TCA001
Cable Assembly, Insulated Push-on F to RJ45 Plug, 849160004783
-
product
VTAC, Patchcord, Receiver, 36", VTAC, To Mini SAS HD Plug
7-142896722-036
VTAC, Patchcord, Receiver, 36", VTAC, to Mini SAS HD Plug
-
product
Micro Coax, Patchcord, Receiver, 36", 50 GHz, Flex 405, to 2.4 MM Plug
7-371105764-036
Micro Coax, Patchcord, Receiver, 36", 50 GHz, Flex 405, to 2.4 MM Plug.
-
product
Micro Coax, Patchcord, ITA , 72", 50 GHz, Flex 405, to 2.4 MM Plug
7-372105764-072
Micro Coax, Patchcord, ITA , 72", 50 GHz, Flex 405, to 2.4 MM Plug.
-
product
3 Digit LCD Voltmeter
DPM 2000
The DPM 2000 is a 3 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV d.c. full scale reading, a bandgap reference, auto-zero, auto-polarity and a set of annunciators. The meter plugs directly into a DIL socket or can be panel mounted using the bezel and window. Connection to the meter is via two rows of pins.
-
product
Automated Digital Ground Continuity Tester
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
-
product
Acoustic Emission Testing Equipment
1283 USB AE Node
The 1283 USB AE Node is a full-featured, low-cost Acoustic Emission testing equipment that plugs conveniently into and is powered by the USB port of a user’s PC or laptop to maximize portability and versatility.
-
product
ARINC 429 Test And Simulation PMC Module
PMC-429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
KVM Over IP
The ultimate zero latency, scalable, 4K60 solution. Pathfinder provides a zero latency, 4K KVM extension and switching solution. Extend 4K and HD sources via CAT or Fiber cable to create flexible, wide reaching KVM over IP matrixing solutions. Highly scalable, with up to 3,000+ high-quality endpoints in a single system, it’s the perfect solution for mission critical control and collaboration. Pathfinder offers plug and play set up with no configuration of endpoints required, nor any costly user licensing fees.
-
product
Rackmount Kit For Infiniium EXR-Series, 8U
EXR2RACK
The EXR2RACK rack mount kit includes all parts needed to mount your Infiniium EXR-Series oscilloscope in an 8U open frame rack and includes a Support tray, Trim plates, BNC connectors to be inserted into the bottom trim plate, black rubber stoppers to plug holes in bottom trim plate if the hole is not being used for a BNC connection, Two track rails, Two clamp brackets, both right and left Top clamp brackets, screws, and nuts.
-
product
125-Watt DC/DC Converter, 3U cPCI
55LQ3
NAI’s 55LQ3 is a 125 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
