-
Product
Signature Compression Only Load Button Load Cells
SLB SERIES
-
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Battery Cell Surge Tester
Chroma 19311
-
Chroma Systems Solutions, Inc.
The 19311-10 has 10 channels, which can test up to 9 battery cells via scanning test, with a single unit. It can support up to 25 channels for testing up to 24 cells in a sequence by connecting with an external scanner (A190362). The test speed of the multicell scanning test by 19311-10 is extremely efficient, saving test time, and decreasing labor costs. It also increases the production capacity of the production line.
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
-
Product
Live Cell Imaging And Analysis
-
The Incucyte Live-Cell Analysis system is designed to efficiently capture cellular changes where they happen - in the incubator. Capture high-resolution fluorescence and bright field images and record data in real time over hours, days or weeks. From proliferation assays to immune killing of tumor spheroids, this flexible system enables users to observe and quantify complex biological changes in real time. Integrated software simplifies data analysis to speed time to answer while producing publication-quality graphs and plots.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Laboratory Electrolyzer Cell – Borosilicate Glass, 100–300 ML
TPR-1
-
Laboratory-scale electrolyzer cells designed for electrolysis, electrocatalysis, electrode evaluation, and electrochemical research. Manufactured from borosilicate glass and compatible with plate or mesh electrodes.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Working Electrodes for Flow Cell
-
Our working electrodes for flow cell are mounted in blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hardness and organic slovent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purporses.
-
Product
H-Type Electrolytic Cell
HT-1
-
Modular dual-chamber electrochemical reactor with a replaceable ion-exchange membrane, available in sealed or non-sealed versions. Ideal for membrane-separated electrolysis, electrocatalysis, gas-involved studies, water splitting, CO₂/N₂ reduction, and mechanistic electrochemical research.
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
-
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Compression Load Cell
EST-20
-
Technopark Automation & Control
The EST-20 is an industry standard Compression Load Cell that can also be used in tension. This load cell can be supplied with load button and cup as well as ball and cup mounting options and is typically used on high capacity silos, hopper scales, batching systems, platform scales, force measurement and tension measurement applications. It is available in capacities from 1 ton to 50 ton.
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
Product
LC/MS/MS Method Package For Cell Culture Profiling Ver. 2
-
This Method Package enables the analysis of 125 compounds in under 20 minutes per sample. Performing analysis separately for each compound group such as amino acids and vitamins makes profiling of cell culture components very laborious, but with this method package a large number of culture medium components and secreted metabolites can be analyzed simultaneously.Compared to the previous version, several metabolites derived from amino acids, nucleic acids and the TCA cycle have been added, allowing even more comprehensive profiling information to be gathered.
-
Product
Swagelok-Type Air Battery Test Cell
STA1
-
STA1 Swagelok-Type Air Battery Test Cell is designed for solid-state battery, liquid battery or in-situ electrochemical research where stable assembly pressure, reliable sealing and repeatable cell geometry are important. It supports laboratory-scale testing, method development and custom battery fixture projects.
-
Product
Battery analyzer For Coin Cell 5V20mA
TOB-5V20mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Analyzer (0.1-20mA, up to 5V) Lithium Coin Cell Battery Research. TOB-5V20mA Battery analyzer is an eight-channel battery analyzer to analyze small coin cells with a range current 0-20mah, voltage 0-5v.
-
Product
Beam Load Cell
EST-70
-
Technopark Automation & Control
The EST-70 Shear Beam Load Cell is commonly used on platform, hopper weighing and pallet weighing applications. It is low cost and available in capacities from 500 kg to 2000 kg.
-
Product
Scienlab Battery Test System - Cell Level
SL1007A
Test System
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
Product
Standard Shackle Load Cell
SS-3.0
-
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
Product
Bending Beam Load Cell
-
Futek Advanced Sensor Technology, Inc.
Are the best fit for many measuring tasks. Here, the signal, on principle, depends on the bending moment.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Acrylic Electrolytic Cell
CAE-1
-
Custom acrylic electrolytic cell for electrochemical testing, electrolysis, and electrodeposition. Transparent PMMA body with customizable ports and dimensions.
-
Product
PXI Mixed Configuration Relay Module - 5 Cells Populated
40-138-AA-BB-CC-DD (5 CELL)
Relay
The 40-138 2A Relay Module with 5 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
PXI Mixed Configuration Relay Module - 3 Cells Populated
40-138-AA-BB-CC-DD (3 CELL)
Relay
The 40-138 2A Relay Module with 3 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Through Hole Load Washer Load Cell Compression Only
LWO SERIES
-
The LW0 Series are washer shaped, strain gage based load cells that have been most commonly used in fastener testing and thru hole load applications. Our stocked ranges from 2,400 through 300,000 lb compression are made from 17-4ph heat treated stainless steel and are matched to bolt diameters and their specific load characteristics. Modifications of diameters, thicknesses, or load range to a specific diameter for OEM applications are welcomed. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Custom Compression Blocks & Spacers For Solid-State Battery Test Cells
CEP1
-
Precision-machined titanium alloy electrode posts, compression blocks, and spacers for solid-state battery test cells and electrochemical research. Available in custom sizes and configurations, these components provide stable mechanical support, reliable electrical contact, and excellent corrosion resistance.
-
Product
Acrylic Microbial Fuel Cell With Ion Exchange Membrane
MFC-1
-
MFC-1 Acrylic Microbial Fuel Cell with Ion Exchange Membrane is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation or customized electrochemical workflows depending on the model. Choose the cell volume, window material, sealing method and port configuration according to electrode size, electrolyte compatibility, gas control and characterization method. For custom experiments, confirm electrode spacing, membrane requirements and temperature control before ordering.
