Discrete Semiconductor Testers
check connected individual semiconductor components.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
-
Product
Megohmmeter Insulation Tester
AMIC-30
-
The AMIC-30 insulation tester is a small portable meter designed to measure insulation resistance in electrical and telecommunications installations, cables, motors, transformers and other equipment. The test voltage can be programmed in steps from 10 V to 1000 V. The instrument can measure both insulation resistance over a wide range (0,1kΩ...100GΩ), and insulation leakage current, capacitance and other parameters. All test results can be stored in the internal memory and sent to a computer via the included wireless USB receiver. The meters are supplied with rechargeable Ni-Cd batteries.
-
Product
CCTV testers
-
1.IPC Tester ,Support H.264/H.265 4K HD IP Camera.2.POE 48V Power Output,Max 24W;3.Support ONVIF, dahua, Hikivision, ACTi,samsung IPC.4. 4.3 inch 800*400 capacitive screen, image display more clearly;5.Built-in WIFI function,can test the Wi-Fi IP Camera;6.Support IP PTZ control functions (ONVIF).7.Support DC12V1A power supply output.8.Support Audio input test.9.Support 4K HD video files and Screen projection function.
-
Product
HBM Verification Tester
HBM-VT
-
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
Product
Clamping Force Tester
KRD102
-
KRD102 series clamping force tester is an indispensable test method for improving products into high-quality fields. It is suitable for research, development, quality control and manufacturing of electronics, electromechanical, optoelectronic, automotive, toy, packaging and other industries. It can simulate the situation that the goods in the container are clamped when they are transported from the container to the warehouse. Whether the goods are damaged due to the clamping, so as to evaluate the anti- clamping ability of the packaging.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
-
Product
Trailer Tester
Inspector 930
-
The Inspector 930 trailer tester is a complete, all-in-one trailer diagnostic system which simplifies ABS, brakes, air, lights, and electrical testing. It provides the ability for a single technician to perform a full inspection in one trip around the trailer.
-
Product
Multicom Tester
IQ2010
-
The LitePoint IQ2010™ is a comprehensive, one-box test solution for all your connectivity testing needs:WiFi, 802.11a/b/g/n and 802.11pBluetooth, Classic (1.x, 2.x, 3.0) and Low Energy (4.0)GPSFMMIMOWiMAXZigBee
-
Product
Heat Shrinkage Tester
RSY-01
-
Film Shrinkage tester, known as free shrink tester, is used for analyzing the effect of temperature on heatshrinkable films made from polyethylene, ethylene copolymers and their mixtures.
-
Product
6-24V Circuit Tester
1656
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. The most essential for troubleshooting automotive electrical systems. Make it easy to find out where current is present.
-
Product
Electrical Safety Tester
GSC60
-
One instrument for all electrical safety tests and Power Quality analysisGSC60 was designed with the aim of making safety of electrical installations visible and valuable, easily and quickly.
-
Product
Insulating Oil Tester
OTSA series
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Tests as per international standards• Auto / Manual mode• 100 test result storage capacity• Large LCD display• Built in printer• User Friendly RS 232 Interface• Safety protection• Accurate performance
-
Product
Transformer Testers
-
*Quickly tests deenergized power distribution transformers*Briefly energizes the transformer and takes a snapshot of the condition by measuring the voltage, current and power factor of the test signal*Tests overhead, pad-mount and distribution transformers*Audible alarm confirms successful test*Improve SAIDI statistics by quickly testing and getting the transformer back in service*Auto self-test performed with every test*Compact, lightweight and easy-to-use
-
Product
MEMS Device-Oriented Testers
-
Are your test requirements oriented to defined families of devices, with common characteristics? You do not need to purchase an expensive, general-purpose mixed signal tester: You can rely on SPEA DOT 100, a system designed to answer the test requirements of MEMS and other low-pin-count devices at an incredibly low cost.The DOT 100 is based on a revolutionary per-device architecture: each device under test has a dedicated CPU managing the entire test process, while each card hosts all the resources for the parallel test of 3 devices, in the size of a postcard.
-
Product
Automatic Dielectric Tester
LD-LADT-A10
-
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
Product
LCD Cable Testers
-
Shenzhen Noyafa Electronic CO.,LTD
The main function of NOYAFA LCD Cable Tester is to measure the cable length and check cable errors, by using LCD display can clearly shows the test results to users, making the faulty points visable, so that to save users time and effort.
-
Product
Hall Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
-
-
Product
Cupping Tester
PCE-CPT 20
-
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
Product
Shore Hardness Tester
HT-6510
-
Application: shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials. Shore D is designed for plastics, Formica, Epoxies and Plexiglass. Application: shore C is designed for various foam and sponge.
-
Product
Insulation Tester
-
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
-
Product
Form Testers
-
The highly accurate rotary table machines and spindle form testers of the RONDCOM series can be used in many areas: production, measuring room and calibration lab.
-
Product
In-Circuit Testers
-
Whether you’re choosing from our stand-alone manually loaded ICT tester all the way to our fully automatic In-line test system, Acculogic has the solution for you!Acculogic’s Scorpion family of automated test equipment and in-circuit fixture-based testers were created with one underlining theme in mind: “Cost-effective Testing”.
-
Product
Concrete Hardness Tester
W-M-350
-
The W-M-350 Recording Test Hammer gives you the same quality as the W-M-250 but with the added feature of a built-in automatic chart recorder. Every test you take is automatically recorded as a bar chart on a paper strip.This creates a field record to verify your findings.In addi- tion to this paper record,you can see each test as it happens through the large easy to read window
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc., By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit., Provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
