-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
Regenerative Battery Pack Test System
17020E
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
product
Haze Meter
DRKWGT-2S
Shandong Drick Instruments Co., Ltd.
DRKWGT2S transmittance / haze analyzer is a computerized automatic measuring instrument which is designed based on the People's Republic of China national standard GB241080 "transparent plastic light transmittance and haze test methods" and the American Society for testing and materials standard ASTM D100361 (1997) Standard Test Method for Haze and Luminous Transmittance of Transparent Plastice." It could apply to all transparent, translucent parallel plane sampler (plastic plates, sheets, plastic film,sheet glass) of light transmittance, transmission haze and reflectivity test also applies to liquid samples (water, beverage, pharmaceutical, colored liquid, grease) turbidity measurements in defense research and production workers and peasants to have a wide range of applications.
-
product
AMIDA 3001XP Tester
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
product
Geometrical Measurement Software
PRÜFTECHNIK Condition Monitoring GmbH
Activate your machinery more quickly, and help it run longer. PRÜFTECHNIK geometric laser alignment tools and software enable you to easily check and adjust your machine geometries for: straightness, flatness, level, inclination, plumbness, parallelism, and right angle check. Our tools are powerful, precise, and easy to use on a vast range of machinery—they can measure for the most demanding alignment jobs, including a bore of almost any diameter, and/or any surface type or inclination. Find the right geometric measurement tool for your machines.
-
product
Test Systems
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
product
4 Channel 500 MS/s 12-bit ADC/Digitizer
SIS3350
4 channel 6U VME digitizer/transient recorder with a sampling rate of up to 500 MS/s (for the individual channel) and 12-bit resolution. The board has a width of one VME slot (4TE). The boards multi event and readout in parallel to acquisition functionality make the card the choice for many demanding digitizer applications.
-
product
PXI Resistor Module Quad 8 Bit With 16xSPDT Relays
40-291-121
The 40-290 Series Programmable Resistor Modules comprise a Dual 16-bit or Quad 8-bit resistor chain together with 16 optional SPDT Reed Relays. Connections are made via a front panel SCSI 2 type 68 pin male connector. Programmable resistors may be connected together either in series or in parallel to form many types of configuration.
-
product
GPGPU Processor
VPX6-4955
Curtiss-Wright Defense Solutions
The VPX6-4955 delivers incredible processing power from not one, but two NVIDIA Quadro Turing TU104 GPUs, providing a remarkable 6144 CUDA cores for parallel processing and a 50% improvement in performance per CUDA core compared to the previous Pascal generation.
-
product
Portable PD Diagnostics System
PD-TaD 60
BAUR Prüf- und Messtechnik GmbH
The PD TaD 60 portable PD Diagnostics system is used in combination with a BAUR VLF generator frida for carrying out partial discharge measurement and location.* Comprehensive 360° cable analysis – with parallel partial discharge and dissipation factor measurement* Time-optimised and safe cable condition evaluation* The lightest and most compact PD measuring device up to 60 kVpeak* Developed for portable use on site
-
product
XRD System
SmartLab®
SmartLab includes as standard Rigaku's patented Cross Beam Optical™ (CBO) technology. CBO technology uses simultaneously mounted, simultaneously aligned optical components for both focusing (Bragg-Brentano) and parallel beam diffractometer geometries. Users can switch between the two geometries without the need to remove, replace, or realign optical components.
-
product
Hybrid & Electric Vehicle Dynamometer Testing
SAKOR Technologies Hybrid/Electric Vehicle Powertrain Dynamometer Test System (HEViDyne), winner of the SAE 2008 Technical Award for Hybrid/Electric Vehicle Testing Technology, is a comprehensive solution for performance, efficiency, and durability testing of all types of hybrid and electric vehicle drivetrains, including:*Hybrid assist (parallel hybrid)*Gasoline or diesel/electric (serial hybrid)*Fully electric vehicles
-
product
Multiplexers (MUX)
WDM
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
product
Parallel Plate Dielectric Test Cell
LT-4203A
The LT-4203A Parallel Plate Dielectric Test Cell is designed for measuring the AC loss characteristics and permittivity of solid laminates and panels per ASTM Standard D150‑98, and implements the guarded electrode (three terminal) measurement preferred as the referee method.
-
product
8 Channel 250 MHz 12-bit ADC/Digitizer
SIS3320-250
8 channel 6U VME digitizer/transient recorder with a sampling rate of up to 250 MHz (for the individual channel) and 12-bit resolution. The board has a width of one VME slot (4TE). The boards multi event and readout in parallel to acquisition functionality make the card the choice for many demanding digitizer applications.
-
product
HiFIX High Fidelity Tester Access Fixture
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
product
192 Channel Power Supply
HDPMU
Today cost efficiency is more important than ever. Many manufacturers are working on maximizing multi-site testing. Often maximization can’t be done because of limited tester resources. Salland’s HDPMU gives you up to 192 additional independent parametric measurement units (PMU) channels on a single board. Our solution will increase parallel testing without the need for creating complex device interface board (DIB). It can be used for continuity, functional or parametric tests or simply for device setup or loading. Full integration with the Teradyne IG-XL™ Software, easy set-up and high parallel measurement capability will reduce test costs significantly.
-
product
Autocompute LCR-Q Meter
Model 4910
Aplab Model 4910 is a microprocessor based digital Autocompute LCR-Q Meter that meets today’s laboratory requirements, in the production line and the quality assurance area. It features fully autoranging and automatic operation over a wide range of measurements. Model 4910 measures inductance, capacitance, resistance and quality factor to a basic accuracy of ±0.25% of the reading for values upto 2000H, 2000μF, 2M ohm and Q factor upto 99 respectively. Measurements can be made at a frequency of 100Hz or 1KHz as required and either the series equivalent or parallel equivalent component values can be displayed.
-
product
1 KN Eccentric Roller Grips
These eccentric roller grips are specifically designed for tensile testing flexible materials, such as rubber and soft and semi-hard plastics. Named after the non-symmetric roller design, these grips employ a simple and quick clamping mechanism. They also have a self-tightening action, which maintains clamping of the specimen during testing regardless of any thickness reduction. In addition, the upper and lower grip faces are parallel grooved to help hold these soft materials.
-
product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Optical Measurement
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
-
product
Closed-Loop Servohydraulic Test Bench Control System
Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.
-
product
SAS (Serial Attached SCSI)
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
product
Standard Capacitor
1409 Series
The elements used in 1409 Standard Capacitors are selected for low dissipation factor and are stabilized by heat cycling. They are housed in cast aluminum cases, along with silica gel which provides continuous desiccation. These cases are sealed with high-temperature wax. A well is provided in the wall of the case for insertion of a dial-type thermometer. Three jack-top binding posts are provided on the top of the case, and removable banana plugs on the bottom, for convenient parallel connection without error
-
product
256 Channel Power Supply
IDPS750
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
product
MEMS Optical Sensor Test
For optical sensor test Cohu offers a variety of solutions being driven by requirements for tri-temp, parallelism and stimulus spacing. Customized optical stimulus units are integrated into Cohu’s test handling systems. For light detector test, we implement different types of light sources, such as infrared, ambient- and colored light. We offer different solutions for 3D image sensors combining emitter and receiver tests of LiDAR, Time of Flight and Structured Light devices.
-
product
Vision Measuring Projector
Sinowon Innovation Metrology Manufacture Ltd.
◆ The lifting system adopts linear guide rail and precision screw drive, which makes the lift drive more comfortable and stable;◆ With precision toothless rod and fast movement locking device, ensure return error is within 2um;◆ High accuracy A optical scale and precision working stage, ensure machine accuracy is within 3+L/200 um;◆ HD zoom lens and HD color digital camera, ensure clear image without distortion;◆ With programmable surface 4-ring 8-division LED cold light and contour LED parallel illumination, it can control the brightness of the 4-ring 8-division independently;◆ With powerful iMeasuring2.1 software system , to enhance the control quality;◆ Optional imported contact probes and 3D measuring software, it can help upgrade the machine to be coordinate measuring machine;◆ Optional FexQMS measurement data analysis and real-time monitor software, enhance process control, reduce material consumption;
-
product
4-CH 12-Bit 80 MS/s PCI Express Digitizer
PCIe-9814
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
