Code
See Also: Programming, Scripts
-
product
Rugged Ethernet System Supporting up to Four Independent 8000 Family Avionics Communication Modules
ES-9810/xx
The ES-9810/xx is a rugged ethernet system supporting up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched in a single system. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The ES-9810/xx is supplied with C drivers, including source code. Mating connectors and cable adapters for I/O connection can be purchased seperately.
-
-
product
SNMP & CLI Development
*Monitoring Windows and Linux Servers using secure SNMPv3*Windows and Linux SNMP SubAgent Development Tools*Embedded SNMPv3 and CLI Code Generators*Avionics AFDX / ARINC664 & SNMP*NTCIP Transportation SNMP
-
product
FPGA Toolkits & IP
Curtiss-Wright Defense Solutions
Our tools and source code for use with our Xilinx Virtex and Kintex-based FPGA products include- FusionXF simplifies the development of FPGA-based application code by allowing developers to concentrate on their application without needing to worry about system integration of the hardware and operating system interface. The DDC family of IP cores supports decimation from 2 to 64 in complex mode and 2 to 32 in real mode
-
product
Generates Test Cases on ICE
TrekSoC-Si
TrekSoC-Si automatically generates self-verifying C test cases to run on the embedded processors in SoCs in in-circuit emulation (ICE), FPGA prototyping, and production silicon. This verifies your chips more quickly and more thoroughly than hand-written diagnostics or running only production code on the processors. TrekSoC-Si's generated test cases target all aspects of full-SoC verification and work in a variety of different environments. TrekSoC-Si is a companion to TrekSoC, which generates test cases for simulation and acceleration. TrekSoC-Si extends the benefits of TrekSoC into hardware platforms.
-
product
Expanding In-Circuit Capabilities
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
product
Welcome To GLCD Font Creator V1.0.0
GLCD Font Creator is the ultimate font creation utility for embedded systems. It lets you create fonts for Liquid Crystal Displays (LCD) and Graphic LCD. It provides a very nice and intuitive user interface. GLCD Font Creator lets you create fonts and symbols from scratch, or by importing existing fonts on your system. It lets you modify and adjust them for your needs, apply effects to them, and finally export them as source code for use in your favorite language compiler.
-
product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 1m
A020GMR-C-1B100
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
PLD ISP Feature, GTE 10.00p
K8220A
The PLD ISP feature allows the test developer engineer to specify a configuration bitstream file in VCL digital test file, much like programming a Flash memory device. The PLD ISP feature supports multiple PLD configuration data formats are supported including. Serial Vector Format (SVF), Standard Test And Programming Language (STAPL), Jam, Jam Byte Code (JBC) object files.
-
product
Public Safety Network Testing Solution
With PCTEL’s automated testing solution, you can ensure in-building communications coverage while saving time and money. Test multiple public safety, cellular, and private networks simultaneously using grid or path-based methods. Commission Business Critical and Emergency Responder Communication Enhancement Systems (ERCES). And auto-generate submittable reports for compliance with FCC and local code requirements.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Ferrules, 2m
40-972-009-2m-FU
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 2m, Spring Latch
40-972-068-2m-FU
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Structural Analysis Professional Software
Robot™
Robot Structural Analysis Professional software provides engineers with advanced BIM-integrated analysis and design tools to understand the behavior of any structure type and verify code compliance.
-
product
Static Design Verification
ALINT-PRO
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
-
product
Intelligent Interface Card
IIB-1553-PC104
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
product
Code Readers/Code Scanners
AutoLink AL629
The AutoLINK AL629 can read and erase codes on domestic, Asian and European vehicles, 1996 and newer. In addition to scanning engine codes, the AL629 can also scan ABS, SRS (airbag) and transmission systems for codes.
-
product
X-Series Measurement Applications for EXT
A broad set of X-Series measurement applications for EXT enabling you to characterize, troubleshoot and rapidly create test code for the manufacture of your design.These applications are based on the library of over 25 X-Series measurement applications for benchtop signal analyzers.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Screwlocks
A068SMR-T-6A100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
KEELOQ DECODER
A security component that receives radio signals from a KEELOQ-enabled transmitter (like a key fob), decrypts the unique "hopping" code, and triggers a corresponding action.
-
product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-FU-HV
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 1m, Screwlocks
A068SFR-F-6B100
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Code Test Optimizer
Clover
Clover provides the metrics you need to better balance the effort between writing code that does stuff, and code that tests stuff. Clover runs in your IDE or your continuous integration system, and includes test optimization to make your tests run faster, and fail more quickly.
-
product
Enlarge Environmental Chamber
REXMED REC-480
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Air Quality Click
64202
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
product
Software Test Tool
testIDEA
The basic premise behind the development of testIDEA was simple: if our development tools have access to the source code and binary code of an embedded application, and our debug hardware can access all of the internal workings of the microcontroller, surely we can simply test embedded software on the target microcontroller.
-
product
Time Code Converters
Time Codes are like different languages. All too often communication between various equipment/devices is impossible due to a "language barrier." When you encounter this type of "language barrier," a Time Code Converter can offer a very simple and cost-effective solution by "translating" a time code. ESE provides several Time Code Converters and Time Code Displays with the ability to convert one time code to another. Time Code to NTP Converter units are the most recent addition to this product family.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Condition Based Monitoring
Test Products International, Inc.
Vibration analysis at the touch of a button. Overall machine and bearing conditions: vibration values are displayed with color coded alarm levels for ISO values and Bearing Damage (BDU).
