VME Carriers
-
Product
PMC Carrier Module
DP-VME-5114
-
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
Product
6U Dual 64/100 PMC VME Carrier
V2PMC2
-
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
Product
6U VME Carrier for PMCs and PrPMCs
Ti4400
-
The Ti4400 is a 6U PMC/PrPMC carrier for VME systems and forms the basis of a flexible I/O system. The user can integrate two single PMC modules or one double-wide PMC.
-
Product
VME64x IP Carrier Module
DP-VME-5121
-
Data Patterns DP-VME-5121 VME IP carrier board is a 6U VME bus card that provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.Each IP module supports two interrupt requests. The VME bus interrupt level is software programmable. The software configured interrupt modes are:a.Single level interrupt mode: All IP module interrupts can be mapped to a single VME bus interrupt level.
-
Product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
-
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Carrier Boards
ROM-DB7501
-
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
Product
COM Express Type 6 evaluation carrier board
ATX-M-CC462-T6
-
The ATX-M-CC462-T6 is a fully featured COM Express Type 6 evaluation carrier board designed for use with the WINSYSTEMS Intel® Tiger Lake UP3 COM Express and other COM Express Type 6 modules.
-
Product
M/MA Module Carrier
VX405C
-
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
-
Product
COM-HPC Server Type Reference Carrier Board in Extended ATX Form Factor
COM-HPC Server Base
-
The COM-HPC Server Base is an extended ATX size COM-HPC Server Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Server Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Carrier Boards
ROM-DB7503
-
ROM-DB7503 is the Referenced Carrier Board designed for Advantech's Qseven 2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. it's more easier for the end user to design portable devices by referring ROM-DB7503 design.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
-
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
Qseven® Reference Carrier Board
Q7-BASE
-
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
Product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
-
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
Product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
-
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
-
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
Product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
-
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Carrier Boards
ROM-DB5901
-
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
-
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
-
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
ETX® Reference Carrier Board in ATX Form Factor
ETX-Proto
-
The ETX-Proto is an ETX Reference Carrier Board in standard ATX form factor. Together with the ETX module of your choice and off-the-shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification. The ETX concept has a great many advantages over full custom designs. It reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time.
-
Product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
-
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
Product
Development Board
SOM-DB5920
-
Development Board for COM Express® R3.0 Type 7 Modules. PICMG COM.0 R 3.0 Type 7 Pin out. COM Express ® Basic/Compact module, 10 Gigabit Ethernet support by OCP mezzanine card. Extension: PCIe x16, PCIe x8, 2 PCIe x4.
-
Product
VME Extender
VME64-M-5R
-
VECTOR Electronics and Technology, Inc.
Excellent performance with a multi layer design
-
Product
Compact Carrier Board
CM22002
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22002 is a compact carrier board which matches the dimensions of a COM Express® Basic module.CM22002 is ideal for space constrained applications, and supports extended temperature ranges of -40℃ to +85℃.
-
-
Product
Recorder Carrier Device
RCD
-
The RCD is a carrier signal demodulator for SCADA and Fault Data Recording. the RCD demodulates the carrier to indicate the presence of a relative level of a singal
-
Product
Switch Card Carriers
-
Compatible for use on the VXI platform, these switch carrier products were formerly sold under the Racal Instruments brand name.
-
Product
VME Bus Tester
VBT100
-
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
Product
Mezzanine Carrier
VXI NM-M
-
HM-M is a carrier of mezzanine modules in the VXI standard, it is a VXI module of the size C-1. NM-M ensures the functioning of various modules installed in it, made in the form of mezzanines. NM-M is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog. The carrier of the NM-M mezzanine modules is used as part of information measuring systems based on the VXIbus trunk. Made on a C size board in accordance with the requirements of the IEEE Std 1155-1992 standard.
