Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
product
3U CompactPCI Serial 5-slot SSR w/o RTM w/o Ethernet
1CPCIS-305-R000
3U CompactPCI Serial Backplane with 5 CompactPCI S.0 slots, system slot right, with rear IO: 1x CompactPCI S.0 CPU slot, 4x CompactPCI S.0 peripheral slots, no connectors for Rear Transition Modules, no Ethernet on the backplane.
-
product
3U VPX Power Backplanes
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
product
Compact PCI Express (3U) Generic Carrier Card
ACCx-1
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
product
PXI Prototyping Module, 2-Slot, 15-Pin D-Type
40-225A-602
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
product
Programmable Multifrequency Clock Synthesizer - 6U VPX
Model 5791
- Simultaneous synthesis of up to five different clocks- Eight SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Four programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
product
PXIe-6672, TCXO PXI Synchronization Module
780063-01
PXIe, TCXO PXI Synchronization Module—The PXIe‑6672 is a system timing controller module. It can drive the PXI star trigger lines, import and export PXI backplane clocks and triggers, generate a high-resolution direct digital synthesis (DDS) clock, and generate a high-stability temperature-compensated crystal oscillator (TCXO) 10 MHz Reference Clock for instrumentation. The PXIe‑6672 allows you to synchronize multiple PXI Express systems, synchronize a PXI Express system with external instruments and equipment, and increase the accuracy of instruments within a PXI Express system.
-
product
PXIe-1082, 8-Slot, Up to 8 GB/s PXI Chassis
780321-01
PXIe, 8-Slot, Up to 8 GB/s PXI Chassis—The PXIe‑1082 features a high-bandwidth backplane to meet a wide range of high-performance test and measurement application needs. It accepts PXI Express modules in every slot and supports standard PXI hybrid-compatible modules in up to four slots. The chassis features an extended operating temperature range for applications needing cooling performance.
-
product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
product
9U CTEL Backplanes with system Slot on left 9U8Slot, 3 x P47
103CTEL908-4146R5
Conforms to PICMG basic specification 2.0 R3.0, Versions conforming to PICMG H.110 Computer Telephony specifications, 8-layer and 12- layer controlled impedance stripline design.
-
product
96 Channel I/O and 64 Channel I/P VME Module
DP-VME-3132
The DP-VME-3132 provides 96 channel RS422 differential digital I/Os and 64 channel RS422 differential isolated inputs on the front end and rear side. On the rear side, it is interfaced with the VME 64x backplane.
-
product
VME J1 18 Slot with ADC Connectors
101VMEJ118-0590
VME J1 backplane 18 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
6U CompactPCI Intel® Atom™ Processor Blade
MIC-3398
The MIC-3398 is a Low-Power 6U CompactPCI® CPU blade with best in class price/performance ratio tailored for applications that require a state of the art processor platform based on Intel® Architecture with full IO capability at an attractive cost point. The MIC-3398 supports Intel® Atom™ E3845 and Celeron N2930, J1900 SoC (system on a chip) family previously codenamed Bay trail with a maximum of quad-core 2.00 GHz processing performance. Intel® Atom™ technology provides significant increases in performance and energy efficiency by using the 22nm Intel® manufacturing process making it an ideal choice for control and workstation applications that require passive cooling with a power dissipation as low as 10W. Up to 8GB, dual channel 1333 MHz DDR3L memory with ECC support provide a high performance and robust memory interface for demanding applications. With built-in graphics based on Intel® HD Graphics Technology this blade offers a significant improvement in graphics performance compared to previous generation platforms. Support for an onboard 2.5” SATA-II drive as well as CFast SSDs adds comprehensive mass storage support. On the system side, the MIC-3398 supports 32-bit, 33MHz and 64-bit, 66MHz PCI bus interfaces to a CompactPCI backplane. A rich set of I/O interfaces such as DVI-D, USB3.0/2.0, Gigabit Ethernet and RS-232/422/485 ports round off the feature set. In addition to the single slot wide (4HP) board offering, a dual slot wide (8HP) version of the blade offers additional network connectivity by increasing Gigabit Ethernet port count from two to four.
-
product
3U VPX 3 Slot Power & Ground, 2 x VITA 67
1900002601-9001R
The only assigned pins on these backplanes are for 3.3V, 5V and 12V power, and both ground and utility planes are defined. The remaining pins are all user-defined. The rear connectors are all fully populated.
-
product
6U cPCI / PXI / PXIe 6021 Full Size Chassis
The WIENER 6021 crate series can be outfitted with cPCI, PXI or PXIe backplanes to provide high performance chassis with highly reliable low-noise power supplies for these bus standards. Typical applications are data acquisition, beam line control and test instrumentation.
-
product
Open Frame 6U 34HP Chassis
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
product
14-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB100
The FAB100 features one CPU card slot, four ISA slots, four PCI-E x1 slots, one PCI-E x16 slot, and four 32bit/33MHz PCI slots. This PICMG 1.3 backplane also supports a built-in 24-pin ATX power connector. Furthermore, the FAB100 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491 and AX6145, to house the FAB100 and any customer's industrial integrations flexibly.
-
product
ATCA 5U 7 Slot replicated Mesh 40G
109ATCA507-3003R
The 5U 7 slot ATCA backplane is a replicated Mesh with dual shelf managers, designed to meet 40Gbps (4 x 10G ports) data rates. Elma's ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
2-Slot 64-bit 6U CompactPCI Backplane
cBP-6402
ADLINK offers a wide selection of standard backplanes from single up to 20 slots. Furthermore, a professional OEM team is capable of custom backplanes with a quick turnaround tailored to your specifications. We make designing, developing, prototyping, and maintaining your projects simple & efficient. For all your backplane needs, give us a call, we have a solution for you.
-
product
VME Chassis and Development Platforms
Wallmount/Rackmount, 6U, 19 inch enclosures, backplanes and power supplies.
-
product
Large Board Stencil Printer
MC1200
Manncorp's MC1200 SMT large board stencil printer fills application requirements of large-board assemblers with print areas ranging from two feet to nearly four feet in length, making them ideal for LED, backplane and multi-panel assemblies. These big-board printers, priced at one-half to as much as two-thirds less than competing large-board printers, are ideal replacements for slower and less accurate manual printers.
-
product
3U – 6U SOSA™ Aligned VPX Backplanes
Using a modular concept based on open standards it is common practice in the civil sector to integrate subsystems components from different manufacturers into a single modular system. The SOSA™ Technical Standard aims at such an interoperability in embedded computing for military applications.
-
product
VME J1 7 Slot with ADC Connectors
101VMEJ107-0590
VME J1 backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
PICMG 1.3 Half-Size SBC Backplane
PICMG1.3 SHB backplanes, which are compatible with half-size PICMG1.3 slot SBC. Our PCI/ISA SBC Backplane product line offers levels of mainstream and server-grade choices, supporting your rugged needs in various industrial applications.
-
product
Digital Backplane Interface Board
MSXB 033
The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor.
-
product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-802
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
product
VME64X 7U 18 slot with P0
101V64XM18-0621
7U VME64x Backplane 18-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
product
3U OpenVPX 8-slot Profile BKP3-CEN08-15.2.16-n
65c308-15216-40
3U OpenVPX Backplane 8-slot, VITA 65, Backplane profile BKP3-CEN08-15.2.16-n, payload slot profile SLT3-PAY-2F2U-14.2.3, switch slot profile SLT3-SWH-6F6U-14.4.1 and SLT3-SWH-2F24U-14.4.3, power connections with M3/M4 power bolts.
