Product

High Voltage Pultruded Resin Bond Glass Fiber Rod

-

NEO TELE-TRONIX PVT. LTD

NEO TELE-TRONIX PVT. LTD

This Test Set-Up can be used to test any kind of Drive Insulator used in Circuit Breaker.

Product

Fiber Optic Light Source

-

Huihong Fiber Inc

Huihong Fiber Inc

Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.

Product

Erbium Fiber Frequency Comb

-

AOSense

AOSense

Detailed description of item: The AOSense frequency comb is a low noise, polarization maintaining (PM) device. Key features include a PM fiber architecture centered at 1550nm with turnkey modelocking; a free-running linewidth of the carrier-envelope offset frequency of <200 kHz; a temperature-insensitive all-fiber f-2f interferometer exhibiting fceo beatnotes with SNR > 45dB (300kHz RBW); and dual fast/slow cavity length actuators with a bandwidth of >300 kHz. The repetition rate of the comb is factory set and allows matching across multiple combs for dual comb applications. The optics package incorporates an optical heterodyne module designed for locking to the comb to an ITU-specified laser reference. The comb is capable of supporting an Allan deviation of < 5 x 10-18 at 1 second and ~10-20 after 105 seconds. Add-on features include all fiber extensions to visible wavelengths corresponding to several atomic transitions. An integrated comb electronics package is currently under development.

Product

Polarization Maintaining Fiber Components

-

OZ Optics

OZ Optics

OZ Optics offers a broad range of polarization maintaining components, patchcords, and connectors designed to resolve polarization problems, which are becoming increasingly important in today's higher speed and more complex mesh optical networks. By maintaining the polarization of the signal at its source, our polarization maintaining components minimize polarization mode dispersion and eliminate the effect of polarization dependent loss thereby increasing the quality of the signal that is transmitted throughout the network.

Product

Ultrafast Fiber Optic Photodetectors

DXM Series

-

Thorlabs, Inc.

DXM Series - Thorlabs, Inc.

The DXM series of Ultrafast Detectors are fiber-coupled photodetectors with wide wavelength ranges, as shown in the plot to the right, that are designed to be used for a variety applications. Each provides a high-fidelity electrical output pulse in response to an optical input pulse, and their clean impulse responses have full width half maxima (FWHM) down to 15 ps.

Product

ULI-211CI -Triple Isolated RS-232/422/485 (Terminal Block) To Multi-Mode Fiber Converter (ST Connectors) DIN Rail Mounted

BB-FOSTCDRI

-

Advantech Co. Ltd.

BB-FOSTCDRI - Advantech Co. Ltd.

Converts serial data signals to multi-mode ST fiber optic2 KV 3-way optical isolation (input/output/power); EMI/RFI protectionData rate: up to 115.2 kbpsWide operating temperature: -40 to +80 °CDIN mount, IP20 plastic case10–48 VDC power source required (not included, sold separately)UL Class 1 / Division 2

Product

8 Deluxe Noid Light / 2 IAC Kit Plus One Fiber Optic Noid Light Extension

3621

-

Peaceful Thriving Enterprise Co Ltd

3621 - Peaceful Thriving Enterprise Co Ltd

Kit packs in a deluxe molded plastic case. Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, GM MULTEC 2 and BOSCH 2. One IAC signal test lights for GM TBI and PFI fuel injection system, and one for GM Model 1987 or newer GM Model 700 TBI and PFI fuel injection system. Plus one fiber optic Noid Light extension.

Product

Fiber Optic Test Solution

Eye-BERT Micro 10G

-

Spectronix

Eye-BERT Micro 10G - Spectronix

The Eye-BERT Micro 10G is a low cost, easy to use, all-in-one XFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, diagnostic monitoring, and wavelength tuning (per XFP capability). Additionally, with a click of a button, the Eye-BERT Micro 10G will automatically test an XFP module based on the information it reads from the transceiver and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.

Product

PXI Single 2 Channel Fiber MUX ST

40-855-512-M

-

Pickering Interfaces Inc.

40-855-512-M - Pickering Interfaces Inc.

Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.

Product

Optical Fiber 8×1 Switch

OFSW - 8 × 1

-

Hangzhou Huatai Optic Tech. Co., Ltd.

OFSW - 8 × 1 - Hangzhou Huatai Optic Tech. Co., Ltd.

OFSW-8×1 is a 8x1 prism optical switch. It can support 8 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.

Product

Fiber Optic Sensors And Amplifiers

-

Omron Industrial Automation

Omron Industrial Automation

Omron’s high-performance fiber optic sensors and amplifiers come in a wide variety of configurations to meet your specialized requirements.

Product

Digital Fiber Sensor

FX-500 Ver.2

-

Panasonic Industrial Devices Sales Company of America

FX-500 Ver.2 - Panasonic Industrial Devices Sales Company of America

Thanks to its new “application-specific integrated circuit” (ASIC), Panasonic can solve applications with Fiber Optic Sensors that were previously impossible. Not only can the FX-500 Series reach a response time of 25µs while providing extremely accurate detection, integrated logic functions save you money because external controllers are no longer needed for normal applications and threshold tracking and self-diagnostic functions save time for maintenance. Moreover, the reliability of the detection has increased by 75% compared to that of previous models.

Product

Fiber Tester (ST Type)

21-8683-00

-

LANTAC Techtronics Co. LTD

21-8683-00 - LANTAC Techtronics Co. LTD

The portable design is easy to carry and operation. 2. Low-cost multi-function is more economical. 3. The multiple LEDs display a clear indication. 4. Power saving automatically and Battery low indication.

Product

- 10Base-T to Multimode Fiber Optic Transceiver

Model 373

-

Telebyte, Inc.

Model 373 - Telebyte, Inc.

FEATURES: Extend Lan's over 1 mile; Full Duplex Plug and Play - no software; Uses industry standard fiber optic cables; Impervious to lightning and surges; Total electrical isolation; 10Base FL compatible. Now you can break the distance barrier of Ethernet based Local Area Networks and achieve total system safety from electrical interference and surges.

Product

Fiber Inspection and Cleaning

-

Fluke Networks

Fluke Networks

Dust - just because you can't see it doesn't mean it's not there. A 1-micrometer dust particle on a single-mode core can block up to 1% of the light (a 0.05dB loss). The only way to know it's clean is to inspect it before you connect it. And if it's dirty, it needs to be cleaned with the right tools or you might just make it worse. Know it's clean with our cleaning and inspection tools.

Product

High-Definition Distributed Fiber Optic Sensing

ODiSI

-

Luna Innovations Inc.

ODiSI - Luna Innovations Inc.

Luna’s ODiSI system provides the world’s highest resolution distributed fiber optic sensing solution for strain and temperature measurement. Using low-profile optical fiber as sensors, the ODiSI system maps strain and temperature fields with sub-millimeter spatial resolution, providing unprecedented detail and data insight.

Product

Optical Fiber Cable Testing Equipment

-

Torontech Group

Torontech Group

Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.

Product

Fiber Optic Temperature Sensors

-

OpSens Solutions Inc.

OpSens Solutions Inc.

High accuracy and repeatable optical temperature sensors for your needs. Opsens Solutions’ fiber optic temperature sensors provide second to none performance to various industries.

Product

RF over Fiber Link TX/RX

L-Band

-

QuestTel

L-Band - QuestTel

QuestTel's Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.

Product

Optical Fiber Identifier

-

Anfkom International Co.,Limited

Anfkom International Co.,Limited

It is an essential installation and maintenance instrument.By inserting the fiber into its adapter head,it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.The 3306A optical fiber identifier also allows relative core power display and identification of the 270Hz,1kHz and 2kHz frequencies. When they are used to detect the frequency, the continuously audible tone is activated.There are four types of adapter heads available: 0.25,0.9,3.0 and 2.0.The 3306A optical fiber identifier is powered by a 9V alkaline battery.

Product

Wireless Fiber Inspection Probe - WIS 300

-

Shanghai Fibretool Technology Co.,Ltd.

Shanghai Fibretool Technology Co.,Ltd.

WIS 300 wireless fiber inspection scope is a WIFI/USB dual-use portable digital fiber inspector. With automated PASS/FAIL and fast images focus functionality, and easy pairing to Android™ and Apple© iOS devices, It can quickly check various patch cords and transceivers, display the fiber end face in PC/laptop/ OTDR/Smartphone etc..digital devices with the USB cable or WiFi connection. Under WiFi mode, it can automatically get the image checked and analyzed. Test results can do the pass/fail judges with IEC/IPC criteria. Fiber images and results can be saved on PC and mobile devices in jpg/pdf/excel format for file records. It’s super light and handy to take anywhere anytime for field tests, operation inspections, and lab research.

Product

Datacenter 12 MPO Fiber Optic Testers & Switches

-

Optical Wavelength Laboratories

Optical Wavelength Laboratories

MULTI-PAIR FIBER LINKS are becoming more common than single pair fiber links for high speed communications, especially in data center environments. OWL DataCenter 12 Series test kits automatically test 12-fiber MPO cables and links without requiring cassettes or fanout cables. Higher density connections (i.e. 24, 36, 48, 60 or 72) can also be tested with MPO break-out cables.

Product

Fiber Optical Cabling

-

Rollball International

Rollball International

An optical fiber, or optical fibre in Commonwealth English, is a flexible, transparent fiber made by drawing glass or plastic to a diameter slightly thicker than that of a human hair.