Aggregator Taps
See Also: Test Access Points, Network Taps
-
Product
Aggregator Network TAPs
-
Aggregator/regeneration network TAPs are used to capture 100% full duplex network traffic; the traffic can then be sent to multiple monitoring appliances to analyze your network. Aggregation TAPs support breakout and regeneration/SPAN modes and let you see every bit, byte and packet.
-
Product
Advanced Aggregators
-
Aggregators are devices designed to increase efficiency and port utilization of network packet brokers. They are commonly used at the network edge or in TOR applications where port utilization tends to be low. Aggregators are also capable of pre-filtering traffic prior to sending out to Network Packet Broker’s for advanced filtering or taking the place of packet brokers in applications where only L2-L4 filtering is required. Aggregators improve ROI by reducing the total cost of a network visibility fabric and increasing the efficiency of existing infrastructure.
-
Product
Replication TAPs
-
For situations where you want to monitor a single, critical network segment using several tools, a Replication TAP is what you need. A replication TAP sends copies of the network traffic to multiple monitoring tools simultaneously.
-
Product
Aggregation Analysis System For Biopharmaceuticals
Aggregates Sizer
-
The "Aggregates Sizer" aggregation analysis system enables the quantitative evaluation of particle amounts in the SVP range as a concentration (unit: μg/mL). Aggregations of biopharmaceuticals can be categorized into 3 ranges: IVP (In-visible Particle), SVP (Sub-visible Particle), and VP (Visible Particle), according to their particle size. Until now, no particle size analyzer could cover the SVP range with a single measurement. Therefore, multiple methods had to be used. Aggregates Sizer completely covers the SVP range.
-
Product
Passive Tapping Device
VDSL Phantom™
-
VDSL Phantom™ is a unique passive tapping device for Lawful Interception (LI) of VDSL2 lines. The device records and stores broadband digital information, offering unique advantages to Law Enforcement Authorities (LEAs) looking to capture data between the target and the service provider premises.
-
Product
ProfiShark Network TAPs
-
ProfiSharks are portable traffic capture devices that provide quick packet-level insight anywhere they are deployed. With capture regardless of packet rate and high quality hardware timestamping, ProfiShark delivers high fidelity capture files, forming an ideal starting point for troubleshooting or network forensics. Designed for easy, non-intrusive traffic capture, ProfiShark offers a valuable improvement over less performant options, such as SPAN ports on a switch or direct capture on a laptop. They give reliable insight into the network, ensuring the quality of analysis, and optimizing workflow, without dropping any packets.
-
Product
TAP Extender
JT 2135
-
The JT 2135 allows TAP signals to be extended away from the base JT 2137 (classic pod) by up to 1 meter and retain full pod’s frequency specifications. The active circuitry inside the JT 2135 compensates for the TDO signal return time of the longer interface cable. Multiple JT 2135s can be implemented if a longer extension is required.
-
Product
Passive Network TAPs
ApconTap
-
Our portfolio of passive optical network TAPs captures network traffic under all conditions to simplify network monitoring and security. Each ApconTap model supports common datacenter optical fiber standards with split ratio options availble at 50/50, 60/40, and 70/30. With passive fiber 40G and 100G TAPs, APCON offers short-range, long-range, and bidirectional models to accomodate requirements for high-density, next-generation datacenter deployments.
-
Product
Regeneration TAPs
-
Regeneration Fiber TAPs allow the tapping of fiber optic networks, while mitigating the power reduction of the optical signal that results from splitting.
-
Product
Tap Adapter
-
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
Product
RF Taps
-
Praxsym’s RF Taps afford access to a cable system for monitoring function and performance without interrupting service. The taps also cause minimal insertion loss when the coupled port is open, as in normal system operation. Like all Praxsym products, these high-quality devices have honest specifications, and are well-documented over the bands they are designed for.
-
Product
On Load Tap Changer Analyzer
TAP-4-PLUS
-
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
Product
Tapping Machine
STM-1
-
Tapping Machine Type STM-1 is intended for measurements of acoustic insulation of ceiling in buildings. The unit fulfils Annex A of ISO 140-6/7. These parts of the standard require a tapping machine as a sound source for impact noise measurements. Type STM-1 is available with an optional remote control.
-
Product
M-TAP Fiber Test Tap
-
The Maxcom Fiber Tap (M-TAP) is a portable optical test tool designed to minimize customer downtime. Two Splitters/Taps One Portable Device 80/20 split ratio 50/50 split ratio
-
Product
Aggregates Testing Equipment
-
Aggregates are one of the most important construction materials, used as a composite material in concrete and asphalt, and as a base material in foundations, roads, and railways. The high hydraulic conductivity of aggregates also makes them ideal for drainage applications and as filter media. With so many different applications, ELE’s range of aggregate testing equipment performs a vital role in checking performance characteristics against specifications, quality control, new source assessment and the prediction of in-service behaviour.
-
Product
Tap Changer Analyzers & Winding Ohmmeters
-
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
Product
Network TAP
-
Is a simple device that connects directly to the cabling infrastructure to split or copy packets for use in analysis, security or general network management.
-
Product
NI-9213, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
785185-01
Temperature Input Module
16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The NI‑9213 is a high-density thermocouple input module that is designed for higher channel count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The NI‑9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9213 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
Passive Tapping Solution
GPON Phantom™
-
GPON Phantom™ is a unique passive tapping device for Lawful Interception (LI) of optical fiber lines using GPON technology and deployed in a Fiber-to-the-x (FTTx) topology. The GPON Phantom records and stores broadband digital information, offering unique advantages for Law Enforcement Authorities (LEAs) looking to capture any data between the central office and the target, without being detected, while providing solid evidence with unique identification of the target.
-
Product
NI-9214, 16-Channel, 68 S/s Aggregate, ±78 mV, Isothermal C Series Temperature Input Module
781510-01
Temperature Input Module
16-Channel, 68 S/s Aggregate, ±78 mV, Isothermal C Series Temperature Input Module - The NI‑9214 is a high-density thermocouple input module that is designed for higher channel count systems. The NI‑9214 includes features to increase overall accuracy, such as CJC sensors in the terminal block, component layout to minimize thermal gradients, and an autozero channel for offset error compensation.
-
Product
NI-9210, 4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module
785043-01
Temperature Input Module
4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module - The NI‑9210 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9210 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
783863-02
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
Controller
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
Product
On Load Tap Changer Analyzer
TAP4
-
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
Product
Bypass Network TAPs
-
Bypass TAPs (bypass switches) are used to connect a monitored network segment to an active, in-line security device and monitor the device's health. If your security tool goes off-line, the bypass TAP automatically 'switches to bypass mode' keeping your network link up while you resolve the issue. Garland's Bypass TAPs with failsafe technology guarantee 100% network up-time and let your security devices see every bit, byte, and packet.®
-
Product
Vacuum, Module, ITA, 90 Series, 2 Port Positions, w/ M22.5x1.5 Tap
510108251
ITA Module
Primary mating module 510104260. (May mate with other Receiver modules, as well.)
-
Product
LCA TAP Plug-In
N4370P01A
-
Keysight Test Automation on PathWave (TAP) is a modern Microsoft .NET-based application for standalone use or in combination with higher level test executive software environments. Instrument plug-ins provide test steps that can be added to work-flow sequences without instrument level programming commands. The LCA plug-in steps further simplify automation by handling the interface to both the PNA instrument and the LCA optical hardware and software and providing the test steps for easy configuration.
-
Product
Multi-Protocol Wireless Application Networking System with Open, Integrated, Secure & Scalable System for Data Aggregation & Viewing
Ion
-
Jacobs’ vendor agnostic architecture was designed and implemented with the goal of an open Industrial Internet of Things (IoT) solution. ion© adapts and applies technology that enables our customers to gain efficiencies and savings, through connecting our client’s sites then collecting and displaying data in a unified interface. This provides custom insights to our clients, empowering them to ensure safety and respond quickly. The Jacobs ion© solution has been operationally deployed for over a decade and enables innovative approaches for data accuracy, data timeliness, and safety — greatly improving information flow and productivity.
-
Product
Filtering Network TAPs
-
Filtering network TAPs allow you to filter out the packets and traffic that is not needed by the tool to perform its function. Filtering ensures that monitoring ports do not become oversubscribed with unneeded data. Filtering TAPs are purpose-built hardware devices that let you see every bit, byte and packet.®
