-
Product
Hydrodynamic 33 kHz and 200 kHz Dual Frequency Transducer
Model TC2178
-
Model TC2178 is an optimized and hydrodynamic 33 kHz and 200 kHz dual frequency transducer ideal for navigation and hydrographic echosounder systems. The transducer has excellent piezoceramic elements which will ensure the highest reliability and quality in echosounding.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
Load Washer
5000 Series
-
The Load cell is a stainless steel sub-miniature strain gage based transducer with compensated temperature performance. This type provides measurements up to 20000 lbf with better than ±0.5% (full scale) non-linearity
-
Product
Transducer Simulator
Model TS-16
-
Impedance: 350 ohms nominal. Output Ranges: Fixed rotary switch: 0 to 3 mv/v in 15 steps of .2 mv/v
-
Product
Variable Reluctance Absolute Pressure Sensor
AP10
-
The AP10, Absolute Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full-scale output of 40 mV per volt at 3kHz. The unit operates with carrier systems including the Validyne CD15 sine wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator to produce a high level analog DC output suitable for recording and control.
-
Product
NI-9422, 24 V to 60 V, 8 Channel (Sinking/Sourcing Input), 250 µs C Series Digital Module
779522-01
-
24 V to 60 V, 8 Channel (Sinking/Sourcing Input), 250 µs C Series Digital Module - The NI‑9422 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel accommodates 24 V to 60 V digital input signals. The NI‑9422 features channel‑to‑channel and channel‑to‑earth ground isolation for the highest level of safety for automotive and industrial environments The NI‑9422 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization.
-
Product
Torque Transducer
T12HP
-
One torque sensor, multiple functions only T12HP can do this. Its superior basic accuracy guarantees precise values over the entire measurement range. This results in the FlexRange capability that only T12HP can provide without the need to switch the measuring range like so called dual range sensors do.
-
Product
Combined Pressure and Temperature Transducers
-
We offer some different styles of combined pressure and temperature transducers which are well suited to Motorsport applications. These include the EPTT5100 combined pressure and temperature transducer, which, has an internal temperature sensor, and the miniature EPTTE1400 combined pressure and temperature transducer which has an external temperature probe.
-
Product
ADC DAC Module
ZET 220
-
ZET 220 ADC DAC module with 24-digit ADC converters is used for high-precision signals measurements in wide dynamic range. The signals to be measured are received from primary transducers – for instance, from sensors with 4-20 mA current output.
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
Torque Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Torque Measurement Trainer comprises of strain gauge based reaction type torque transducer, fulcrum arm of 1 M length with L angle to mount the sensor, Pan & weights with digital torque indicator to read the torque in Kg-m.
-
Product
Loading Bench
-
Effortlessly perform a torque wrench calibration with a mechanical torque wrench loader. The loading bench is a laboratory grade instrument designed to enable accurate torque wrench calibration with less physical effort. The calibration instrument enables quick and easy torque wrench calibration and presetting, independent of human influence or transducer side and end load factors.
-
Product
Closed Loop Hall Effect Current Sensors/Transducerswith Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used formeasurement of DC and AC current, pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
Acoustic Emission Transducer
GT301
-
Acoustic emission transducer GT301 converts acoustic signal into electrical signal, parameters of which are used for acoustic emission source evaluation.
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Power Frequency Transducer
TDF
-
Kusam Electrical Industries Limited
• Dual Aux. Power 110/220V AC• High Accuracy 0.2% RO at 23 °C± 5 °C• High Dielectric Strength 2.6KV AC / Min, Between Input / Output/ Power Case• ABS Plastic Case, DIN Rail or Wall Mounting
-
Product
Hardy Shaker
HI-903
-
This is our top of the line Hardy Shaker. It provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting vibration tests easier. Tests can be conducted on multiple vibration transducers, and then the saved data can be transferred via USB Flash Drive to be displayed in an automated and customizable report using an Excel template on your computer. In manual mode, the vibration test level and test frequency can be set from 7 Hz to 10,000 Hz. The high accuracy instrument can display the vibration level in terms of g’s peak, velocity peak (in/sec or mm/s) or displacement peak-to-peak (mils or µm). The unit can support payloads up to 800 grams (see frequency limits in the manual). A built-in display reads the output sensitivity, which can be stored in memory. Complete testing sequences and data can be stored in memory for each tested sensor, the unit logs the data on the spot or stores it for later use. For testing of heavy transducers or at high frequencies, the HI-903 automatically corrects the sensitivity calculation for the effects of transducer mass loading. A built-in self-test program checks for accuracy of all calculations. The HI-903 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
Product
4-20mA Bridge AmplifierR
90416
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
783907-01
-
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, … features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
Three Phase Power Calibrators And Tester Of Power Engineering Devices
C300B
-
Calmet Smart Calibration Devices
Three phase, class 0.02 and 0.05 power quality calibrator up to 120A (360A) and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
Product
Accessories
-
Check out the full line of quality Amprobe accessories, which are field tested to help you get the most out of your Amprobe tools, including:*Rugged test leads of all types and sizes for Amprobe instruments*Current transducers for maximum accuracy and safety*Temperature accessories for surface, air/gas, or liquid temperature measurements*AC relays for low-voltage control circuits*Adapters, software, carrying cases and more
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Portable Digital Manometer
PS309
-
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
Product
Level & Pressure Transmitters
-
This series of low-pressure transducers is specifically designed for demanding industrial applications where the primary criteria are reliability and economy. These units provide repeatable, precision measurements under the most hostile condition.
-
Product
Advanced Clamp-On Ultrasonic Flowmeter
KATflow 150
-
The KATflow 150 is the premier product for flexibility and performance, providing the user with a comprehensive specification and a list of configuration options. The practical modular design and the wide variety of different transducer types available ensure this instrument is suitable for everything from simple water flow measurements to energy flow monitoring and automated process control.
-
Product
Normal Incidence Shear Wave Transducers
-
Single element normal incidence Shear Wave Transducers contact transducers introduce shear waves directly into the test piece without the use of refracted wave mode conversion. We recommend the use of our SWC shear wave couplant for general purpose testing.
-
Product
Servo type Accelerometer
-
A motion is sensed by a displacement detector, a current is fed to the coil to get back the pendulum mass to the original position. This current will be proportional to the acceleration, that is converted to an output voltage. The Servo type accelerometer is for the Earthquake Monitoring or measurements of micro tremor on the Civil Engineering Structures because of its higher sensitivity and stability or more accurate phase responses in the lower frequency range than those of other vibration transducers.
-
Product
Temperature Transmitter
T4111
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured temperature is converted to linearized unified signal 4-20 mA. Measured values are displayed on LCD display. It is possible to switch OFF theLCD at all. Current loop has two-wire connection and requires power from evaluation device.
-
Product
Fixed Clamp-on Flowmeter
D118
-
Gentos Measurement & Control Co.
The D118 ultrasonic flowmeter is based on Tansit-time technology, which has ultra-high measurement accuracy. D118 uses an external clipped Transducer, which can collect flow data simply by clamping it on the outside of the pipe, and it will never come into contact with the fluid, and will not cause liquid pollution, pressure reduction, leakage, etc.
-
Product
Motorsports Sensors
-
Variohm have many years of experience of providing sensors and transducers to the Motorsport Industry in all series. Take a look at our range of Motorsport Sensors below.
