PMC
PCI Mezzanine Card
-
Product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
-
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
Product
PIM-Carrier-Dual
-
The PMC Carrier routes the PMC IO from P14/P24 to J3/J5. The PIM-Carrier-Dual routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis. The PIM can match the pinout of the front bezel IO to allow for common cables to be used for front and rear IO.
-
Product
Programmable Multifrequency Clock Synthesizer - PMC
Model 7191
-
- Simultaneous synthesis of up to up to 5 different clocks- Eight SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 100 MHz- Four programmable VCXOs with 32-bit tuning resolution- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status via PCI bus interface
-
Product
ATCA Rear Transition Module
ART103
-
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.
-
Product
Cots Boards
-
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North America. They are used for system level products such as Automatic Test Equipment, Rugged Military Electronics, etc.Data Patterns focus on building COTS product is to provide the technological capability to develop system level products with very fast run around times. Use of Data Patterns' COTS module in system level products ensures Data Patterns ability to maintain the products for a significantly longer life cycle. The proximity to the system level engineering team with the COTS development team ensures that end applications are delivered faster, enabling a shorter time to market for the customers
-
Product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
-
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
Product
32-bit PMC to PCI Adapter
8092
-
This PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
PMC Compatible Wizard Interface
PMC-Wizard
-
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
Product
CompactPCI
3U PMC Carrier
-
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
-
Product
Spartan-6 FPGA Modules with Plug-In I/O
PMC-SLX
-
Acromag’s cost-effective PMC-SLX modules feature a user-configurable Xilinx® Spartan®-6 FPGA enhanced with high-speed memory and a high-throughput PCI-X interface. Field I/O interfaces to the PMC FPGA via the rear J4/P4 connector and/or with optional front mezzanine AXM plug-in I/O modules. The result is a powerful and flexible I/O processor module that is capable of executing custom instruction sets and algorithms.
-
Product
PCI Carrier Board
MS 1714
-
*64 bit PCI edge connector*64 bit PMC connectors*Operated frequency up to 66MHz*Regulated 3.3v supply to module
-
Product
Radar Scan Converter PMC
Eagle
-
Curtiss-Wright Defense Solutions
Eagle is a flexible and powerful radar scan converter that is based upon field-proven technology and comes in a compact and mechanically ruggedized PMC form factor. Eagle features a low power, rugged design, enabling it to operate in a wide range of environments, including conditions of high temperature and vibration.
-
Product
Test Adapter
PMC-UNIV-TEST
-
PCI adapter for PMC with options for PCI and PMC Stack Pass through connections
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
-
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
PMC to PCI Express Adapter w/ TSI384
6083
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
Product
PMC Carrier Module
DP-VME-5114
-
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
Product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
-
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
Product
PMC Module
PMC-CycloneII-64LVTTL
-
User Programmable Altera Cyclone II FPGA 672 BGA, EP2C35, EP2C50, EP2C70, Stand alone possibility, Single wide PMC Module, 64 LVTL, Optional User clock oscillator
-
Product
NETernity
PMC942RC
-
The NETernity™ PMC942RC is a fully integrated 8-port 10/100/1000BaseT Ethernet switch designed to support the low-cost requirements of unmanaged switch applications and converging networks. Seven of the ports are external; the eighth port appears as a NIC (Network Interface) to the host SBC to which the PMC is attached.
-
Product
PMC-BiSerial-Nvy1
-
PMC-BiSerial-Nvy1 provides multiple serial protocols. The Nvy1 protocol implemented provides Manchester encoded data inputs and outputs.
-
Product
Mezzanine Module
RS485-MOD2
-
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
Product
PMC to PCI Express Adapter w/ TSI384
8636
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI Express primary side and a PCI/PCI-X secondary side.
-
Product
Expansion Card
PMC238
-
The PMC238 is a 6U form factor card that expands a single PMC site on a VMEbus processor board to two PMC sites and one PCMCIA/CardBus socket or to three PMC sites. Compatible with many VMEbus single board computers, it provides an extension of PCI and PCMCIA capacity within the VMEbus form factor. The PMC238 has the option for the PCMCIA/CardBus cards to be mounted outside the chassis using an 18-inch cable.
-
Product
ARINC-429/717 PMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
PMC-A429
-
The PMC-A429 card is based on the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, and a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and flexibility while reducing integration time.
-
Product
PMC-BiFIFO
-
The parallel Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The 32 RS485 channels are programmable as input or output allowing for a variety of implementations. The programmable output rates and RS422/485 compatability will interface to a multitude of systems.
-
Product
PMC Card
P-DIS
-
The P-DIS PMC card is different from most currently available data acquisition boards. It provides multiple I/O types on a single module and the functionality to work with high-speed digital I/O signaling. With very accurate time stamping of input data and synchronization to an external IRIG-B source, the P-DIS provides the capability to precisely synchronize all output ports.
-
Product
PMC/XMC Expansion Card
EXP238
-
The EXP238 is a 6U VMEbus form factor expansion card offering three XMC/PMC expansion sites. When ordered as an option for the XVB603 VMEbus single board computer, the 3-slot solution greatly expands system flexibility.
-
Product
High Density 68 pin
HDEterm68
-
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
-
Product
PMC Module
PMC-MON16LED
-
• Fully compatible withGE Fanuc / RamixPMC498• PCI MezzanineCard (PMC) IEEE1386• 16 LEDs• Two RotarySwitches for 256Combinations• Read / Writeable• Monitoring LEDs• Front panel I/Oaccess
