Current Sensors
detect AC or DC electrical current.
See Also: Current Probes, SQUID, Voltage Sensors, Rogowski
-
product
Force Sensors
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
product
Resistance Temperature Sensors
Watlow Electric Manufacturing Company
These sensors are suited for applications where accuracy and stability are essential for proper control in applications that operate at or below 1200°F (650C).
-
product
Current Tester
MIG0624
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
product
Fence Vibration Sensor
ENVIROMUX-FENCE1
Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.
-
product
Temperature Sensors
A device, typically, a thermocouple or RTD, that provides for temperature measurement through an electrical signal.
-
product
AC / DC Current Clamp
HT9025
HT9025 has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/ EN61010-1.
-
product
Current Sensing
A current sense amplifier is a differential amplifier providing an analog output voltage proportional to the current flowing into a load connected on its input.
-
product
CW Power Sensors
E-Series
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (-70 to +20 dBm)Accurate CW average power measurements Wide frequency coverage from 10 MHz to 26.5 GHz (sensor dependent)Calibration factors stored in EEPROM
-
product
Citroen Oxygen Sensor
KS60113 - Citroen
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Soil Moisture Sensor
SoilWatch10
SoilWatch 10 is a soil moisture sensor which allows measuring relative water content in the soil. Our sensor does not have any exposed electrodes that usually corrode in resistive sensors. Whats more the reads will almost not drift over time or with temperature changes. Our sensor will give the same readings regardless of supply voltage. The sensor is weatherproof. It can be buried in soil for extended periods of time without adverse effects on accuracy or reliability. Designed to work with Arduino.
-
product
Wireless Sensors
Designed to measure specific parameters about their physical surroundings and produce outputs, often electrical signal
-
product
Cylindrical Photoelectric Sensor
CY-100 SERIES
Panasonic Industrial Devices Sales Company of America
CY-100 Series Sensors are available as Thru-Beam, Retroreflective (with and without polarization filters) and Diffuse Reflective Types. Standard (Axial) and Side-View (Radial) Types are available, providing flexibility when mounting the Sensors. Moreover, all Sensors can be ordered as a cable type or with an M12 plug-in Connector.
-
product
Phase Meter Current Shunts
610 and 650
Clarke-Hess Communications Research
The Model 610 and 650 Current Shunts are specifically designed to operate with the Model 6000A Precision Phase Meter. These shunts are frequency tuned to have negligible phase shift (less than 5m) at 50/60Hz making them ideal for line frequency applications. They can also be idealized for other frequencies as specified by the user. Consult factory for details.
-
product
PIR Mini Sensor
28033
Do you have a big idea that needs a small motion sensor? The PIR Mini Sensor’s compact form factor is ideal for small-scale projects, and those where the electronics need to be hidden or protected. The narrow, vertically oriented board can slip through a hole in an enclosure to hide and protect the electronics, leaving only the small lens visible on the outside.
-
product
Sensor Evaluation Kits
Panasonic Industrial Devices Sales Company of America
Accelerate prototyping and testing by utilizing Panasonic's Sensor Evaluation Kits for all your design needs. Discover today why Panasonic Sensors are the premier choice for creating unique IoT solutions.
-
product
Sound Velocity Sensor
miniSVS
The Valeport miniSVS uses digital "time of flight" technology to provide the lowest noise, highest accuracy, best resolution sound velocity data available.
-
product
Luminescence Sensors
Luminescence sensors detect visible and non-visible marks that illuminate when using ultraviolet (UV) light. Fluorescent material and marks are reliably detected independently of their pattern, colors or surface conditions on any material. Luminescence sensors emit UV light with a wave length of approximately 375 nm. Fluorescent substances convert the UV light into long-wave visible light, which is then received and evaluated by the luminescence sensor.
-
-
product
DC/AC Earth Leakage Current Measurement
FDAZCT-11L-0.4
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bipolar ±15V Power Supply.*Output ±5V at primary nominal current.*Applicable Frequency DC-18kHz.*Inside Diameter:φ11mm
-
product
Barometer Logger Sensor
NUL-221
This logger sensor measures atmospheric barometric pressure and can display data in four common units. kPa kilopascal atm atmospheres in Hg inches of mercury mm Hg millimeters of mercuryThe sensor also offers an option to display the measured pressure values in terms of altitude (in meters).
-
product
Surface Temperature Sensors
Campbell Scientific offers two types of surface temperature sensors: infrared temperature (non-contact) and surface contact. Infrared temperature sensors measure the surface temperature of an object or surface by sensing the infrared radiation given off by the subject. Surface contact sensors attach directly to a surface and measure the temperature via physical contact.
-
-
product
Strain sensors
SG-01
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
-
product
Current Measurement in a Compact Design
ICD-Series
Isabellenhütte Heusler GmbH & Co. KG
The ICD series is a compact system for current measurement. The ICD-A is suitable for an application in the automotive industry due to its connector, while the ICD-C is more suitable for the design industry. The shunt-based measurement provides for a high level of accuracy and temperature compensation is also incorporated through the internal signal processing. External temperature influences are thus reduced to a minimum.
-
product
Flow Sensors
Accuracy±0.75% of full scale Measuring pipe size range DN 15 to DN 600(0.5 to 24 inch) Measuring flow rate range 0.15 to 8 M/s(0.5 to 26 Ft/s) Field-rangable supply voltage from DC 5 to 24 VS Field-rangable operting temperature from -20 to 90°C(-4 to 194°F) Protection class NEMA4(IP65) or NEMA6,6P(IP68) CE EMC certification
-
product
ESD Voltmeters And Sensors
Achieve High Accuracy Without Fixed Spacing Requirements. We offer diagnostic tools for ESD in-line sensing and hand-held electrostatic voltmeters that are ideal for use in ESD-sensitive environments. Accurately measures surface voltage or charge build-up over a wide range of spacings.
-
product
Microbolometer Sensors
Calibir GX Family
The Calibir GX camera family features our latest microbolometer sensor, designed, fabricated, and packaged in our own foundry. With great sensitivity in longwave infrared range (8-12 µm), it features both shutter and shutterless operation and rapid image output on power up while delivering uniform response over the entire operating temperature range, making it an ideal component for thermal imaging systems requiring uninterrupted image acquisition. The GX series also offers our own advanced 21-bit ADC design for unparalleled intra-scene dynamic range without the need for a gain reduction, allowing for the best possible NETD over a vast range of temperature (>600C).
-
product
Optical Sensors
Many measurements are much easier to make with light. Southern Photonics designs and manufactures optical sensor systems for a wide range of applications including gas sensing and strain sensing.
-
product
E-Series Peak and Average Power Sensor, 50 MHz to 18 GHz
E9326A
The E9326A power sensor has a 1.5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA and CDMA wireless formats such as Bluetooth.
-
product
Web Sensor with PoE
T3610
PoE Web Sensor with built-in relative humidity and temperature sensors. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Power over Ethernet feature according IEEE 802.3af is supported. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
