CompactPCI Chassis
A metal frame that serves as the structural support for a CompactPCI bus. (sbc.webopedia.com)
-
Product
6U CompactPCI Switches
-
CompactPCI Switches 6U or 3U managed Gigabit Ethernet switch blades.
-
Product
2U Rackmount Chassis
ACP-2320
-
2U Rackmount Chassis for ATX/ MicroATX Motherboard with Low-Profile Rear Bracket Option
-
Product
Open Frame 6U 34HP Chassis
-
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
Product
3U CompactPCI Serial 2-Port Serial Card
cPCI-A3COM
cPCI Card
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x DB9 COM ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
Power Module
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
Product
Chassis 8 Slot
PXIe 4U/ 42HP
Chassis
As PXI has evolved into high-speed serial fabric technology, so has the Hartmann Electronic product line with the addition of its PXIe solutions. More power, more bandwidth, more functionality.
-
Product
3U Format CompactPCI (CPCI) Bus IP Carrier
CPCI-SIP-2
Bus Extender
The CPCI-SIP is a 3U format CompactPCI (CPCI) bus IP carrier. The CPCI-SIP-2 provides mechanical support and the electrical interfaces for two single width IP modules, or a double width IP module. Multiple CPCI-SIP-2 boards may be installed in a single system.
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-24
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred
-
Product
6U CompactPCI Intel® 6th Gen. Core™ i3/i5/i7 Processor Blade with ECC support
MIC-3399
Processor Blade
- Supports 6th Generation Intel® Core™ i3/i5/i7 processors and Intel® CM236 PCH with embedded graphic (up to 3 independent displays)- Up to 32GB (DDR4-2133) memory (max 16GB on board, socket SO-DIMM x1, max 16GB)- Optimized dual-slot SBC with 2.5" SATA-III HDD/SSD, 2240 or 2280 M.2 socket, on-board Nandflash (optional)- Two SATA ports, two USB 3.0, six USB 2.0 ports, two DP ports, two COM ports, one PS/2, one Audio, one VGA and PCIe x8 interfaces to the Rear Transition Module (RTM)- Five Gigabit Ethernet ports including two PICMG 2.16 for front and rear connectivity- PICMG 2.16 R1.0, PICMG 2.1 R2.0, PICMG 2.0 R3.0, PICMG2.9 R1.0 compliant
-
Product
18.5" Configurable Panel PC Chassis For Selectable Mini-ITX Motherboards
PPC-618W
-
18.5" true-flat panel PC with multi-touch projected capacitiveSupports certified mini-ITX motherboards (up to 65W TDP processor)PCI or PCIe expansion slotsFront-facing power status LED indicatorsIP66-rated front panelSupport dual HDD drawer
-
Product
15" Configurable Panel PC Chassis For Selectable Mini-ITX Motherboard
PPC-6151C
Panel PC
15” true-flat PPC with Resistive touchSupports certified mini-ITX motherboard up to 65W TDP processorSupport PCI or PCIe expansion slotFront LED indicators for power statusFront panel is IP66 compliant
-
Product
6-Slot Desktop/Wallmount Chassis
IPC-6606
-
Support 6-slot PICMG 1.0 backplane only, Shockproof drive bay for 5.25" ODD and 3.5" HDD. Two front access USB ports, Bidirectional to mount chassis on wall or workbench.
-
Product
1100 HP Water Brake Chassis Dynamometer
CM-51
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
Product
14-slot CH-14 PXIe-PC Chassis
-
The new CH-14 PC PXIe-PC chassis with an embedded PC allows the creation of high-performance multifunctional systems for collecting and processing large flows of information, as well as systems for monitoring and adjusting radio-electronic equipment.
-
Product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
Multifunction I/O
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
3U CompactPCI 9th Gen Intel® Xeon®/Core™ i7 Processor Blade
cPCI-3520 Series
Processor Blade
The cPCI-3520 Series is a 3U CompactPCI blade available in single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width form factors with various daughter boards to provide a broad range of I/O requirements. Faceplate I/O in the single-slot (4HP) version includes 1x DVI-I, 2x GbE and 1x USB 3.0 port (these I/O are common to all versions). Faceplate I/O in the dual-slot (8HP) version includes additional 2x USB 2.0, 1x COM, 1x KB/MS and Line-in/Line-out on the cPCI-3520D or additional 2x DisplayPorts, 1x COM in RJ-45 connector, 1x KB/MS and 1x additional USB 2.0 port on the cPCI-3520G. Two more dual-slot options are the cPCI-3520L with additional 2x GbE, 1x COM and 2x USB and the cPCI-3520M with one 100-pin high density connector supporting additional 2x DVI-D, 2x USB 2.0, 2x COM, 2x KB/MS and Line-in/Line-out ports.
-
Product
6U CompactPCI 9th/8th Gen Intel® Core™ I3/i5/i7 Processor Blade
cPCI-6640 Series
Processor Blade
The ADLINK cPCI-6640 is a 6U CompactPCI® processor blade featuring an 8th/9th Gen Intel® Core™ (formerly Coffee Lake-H) with Mobile Intel® CM246 Chipset. Dual SO-DIMM slots provide up to 64GB of DDR4-2666 dual-channel memory (2x 32GB modules). ECC memory is also available when paired with a supporting CPU.
-
Product
9-slot Chassis
CH-09 AXIe-0
-
The 9-slot chassis in AXIe-0 format is intended for use in modular measurement information systems based on the AXIe standard.
-
Product
Charge-Discharge Chassis For 208 VAC 3-phase
BT2203B
Chassis
The BT2203B is part of the BT2200 Series cell formation and lifetime cycler solution. It is an 8-slot mainframe for 208 VAC 3-phase power.
-
Product
ULI-224TE - Heavy Industrial RS-232 (DB9 Female To RS-422/485 (Terminal Block) Converter. Panel Mount Metal Chassis
BB-485DRCI-PH
-
Converts RS-232 data signals to RS-422/RS-485Three-way 2 KV optical isolation (input, output, power)Wide operating temperature: -40 to +85 °CModbus ASCII/RTURugged IP30 metal panel mount case, DB9 F / TB10-48 Vdc input power (external power supply required, sold separately)UL C1/D2, IEEE-61850-3, IEEE-1613
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
PCIe-PXIe-8565
PXI Express Module
Includes PCIe-8560 peripheral card, PXIe-8565 3U system module, and ACL-EXPRESS cable in 1, 3, or 7 meter lengthsCompliant with PXI-5 PXI Express hardware specification Rev.1.0 and PCI Express Base Specifications Rev. 1.0a250 MB/s maximum system throughput
-
Product
Chassis Dynanometer for Motorcycle
-
•Adopted FAMS-R5 system for motorcycle chassis dynamometer•Gas emission test, durability test, performance test, and environmental test are applicable to various vehicles (motorcycle, tricycle,ATV).•Newly designed measurement unit in a test room makes measurement easier.•Reduction of initial cost, space saving, and less maintenance items by lineup of electric inertia type chassis dynamometer that can be used for small to large vehicles.•Components necessary for emission test are included, such as front wheel holding unit, engine cooling fan, drivers display.•Application software necessary for emission test is installed, such as road resistance setting software, drivers aid,gas emission data processing software, rear axle output data processing software.
-
Product
3U CompactPCI 32-Bit 13-Slot Backplane with Rear I/O
cBP-3213PR
Backplane
- PICMG 2.0 CompactPCI Specification Rev. 3.0 compliant- One system slot and twelve peripheral slots via cBP-*R3213 bridge boar- 10-layer PCB for accurate impedance control and electronic noise immunity- Two ATX sockets with DC screw terminals
-
Product
2U Storage Chassis For ATX/EATX Serverboard With 12 Hot-Swap Drive Bays For High-Capacity Storage.
HPC-8212
-
2U rackmount chassis supports EATX/ATX/uATX motherboard12-bay hot-swappable 3.5"/2.5" SAS 12Gb/s drives or SATA 6Gb/s drives4 x NVMe drives supported via an optional riser cardDefault 7x slots (low profile) rear panel, 3x slots (full height) optionalSupports Flex ATX Power, 80+ redundant power supply
-
Product
1-Slot 3U VPX Development Chassis for Quartz Products
Model 8257
-
- 1-slot, small footprint development chassis- Optional dual MPO interfaces support 100 GigE- Supports VITA-66.4
-
Product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/24
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output
-
Product
Chassis Platform Accessories
-
Embedded Computing Systems require more than just a chassis housing with backplane, power supply, cooling and payload boards. To complement our wide range of systems, Elma offers a comprehensive range of system level accessories, including I/O solutions, HMI displays, system/power management controllers and test & development boards.
-
Product
8 Slot, 3U, PXI Chassis - Low Noise Fan
40-908-201
Chassis
This PXI chassis includes all the features and performance required by version 2.1 of the PXI standard and supports a control interface or embedded controller and up to seven more 3U peripheral modules. Mechanical expansion space on the right hand side allows the chassis to accept multi-slot modules, such as the BRIC, while only occupying one electrical slot.
-
Product
VPX Chassis 4U/50HP 7 Slots
BKP3-CEN07-15.2.3-4
-
his 7 slot Hartmann Open VPX BKP3-CEN07-15.2.3-4 profile system chassis provides an intelligent, practical packaging solution for high-performance processors. The 50HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with a 600W plug-in power supply and a 1U removable, bottom mount fan tray.
-
Product
Industrial Chassis
-
Axiomtek's industrial chassis are flexible, easily managed, and feature solid designs. Axiomtek also provides a customized ID program in a short amount of time. Axiomtek satisfies various customers' need by supplying the right type of chassis designed for the right applications.
