Inductive Load Banks
See Also: Load Banks, AC Load Banks, DC Load Banks, Reactive Load Banks, Resistive Load Banks
-
Product
24V / 400 Amp Load
EL12-24M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
Product
PXI Solid State MUX, 10 bank, 16 channel
40-680-002
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of feeder
-
Product
Battery Load Bank
-
Foresight Electronics Co., Ltd.
Utility is used for battery systems range from 21-30V, if higher current is needed, two or more FST-24V units can be linked together. Discharge to Battery string voltage as 24V, Cell voltage as 1.2V/2V/6V/12V adjustable stop points and multiple alarm designs to control the discharge process intelligently 7inch LCD touch screen for easy operation and showing various parameters real time Support RS232 real time monitoring by PC or SD Card download data after discharge
-
Product
Motive Power Load Banks
-
The only way to be certain that your stationary batteries will perform to specification is to test the batteries’ capacity with a DC load bank / portable battery discharge tester.
-
Product
3U VPX Conduction Cooled Load Board
1940000446-0000R
-
3U VPX Load Board, conduction cooled.
-
Product
DC Programmable Electronic Load
ELCH300
-
- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR/OV/OC/- OP/OT protection- Communication: USB/RS232/GPIB
-
Product
Self Powered Active Load
TBOH02
-
The TBOH02 is a self powered, precision active load. It does not need a separate supply voltage and operates as low as 2V. Its features include constant resistance and constant current mode. A 10 turn potentiometer with dial, a range switch and a precision reference enable accurate setting of current or resistance. Furthermore it can be controlled by an external voltage.
-
Product
Compact Micro-size Inductive Proximity Sensor
GS
-
Panasonic Industrial Devices Sales Company of America
The Panasonic GS Compact Micro-size Inductive Proximity Sensor has Sensor heads that come in multiple sizes with a separate amplifier controller.
-
Product
Receiver, I2 Micro ICon, 168 Position, Fully Loaded With Twin Female Contacts (610 138 200)
310130101
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is fully loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kit, protective cover, and strain relief are available.
-
Product
Compression Load Cell
EST-20
-
Technopark Automation & Control
The EST-20 is an industry standard Compression Load Cell that can also be used in tension. This load cell can be supplied with load button and cup as well as ball and cup mounting options and is typically used on high capacity silos, hopper scales, batching systems, platform scales, force measurement and tension measurement applications. It is available in capacities from 1 ton to 50 ton.
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
Product
4 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 4 Ports
GPS402
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Waveguide Loads
-
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
Product
Load & Fatigue Testing
-
DATASYST Engineering & Testing Services, Inc.
Due to variations in types and levels of load and fatigue exposure, DATASYST works with each client to determine the best possible test plan to capture the information and issues that may be present in application.
-
Product
1800~3000W DC Electronic Loads
JT633 series
-
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
Product
Extra Pressure up to 200 Bar Peak Pressure Inductive Sensors
-
Contrinex Extra Pressure up to 200 Bar Peak Pressure Inductive Sensors
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
PXI MUX 1 Bank of 64 Channel 2 Pole
40-610-022-1/64/2
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
20V/30A/300W DC Programmable Electronic Load
TOB-IT8512
-
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Auto Load 4 Moving Probe Tester
AL Series F4H4033AL
-
Medium and High Volume Production Model with Auto Loader. Max. Test Area15.7 x 13" (400x330mm). Max. Transferable Panel Size16.5 x 13.4" (420x340mm). Number of Probes2 Upper, 2 Under. in. Pad Pitch *40.00236" (60µm). Min. Pad Size *50.00118" (30µm).
-
Product
Digital Test Light With Load Tester
28800
-
Works as a regular test light and when you push the button on the tool it applies an 800mA load at 12V DC to easily check for voltage drop on circuits. The display will indicate the voltage drop when the button is pushed. Displays voltage under load to tell if circuit has problems like corrosion, resistance, or faulty connections. 48" cord with heavy-duty alligator clamp for secure connections. Not computer safe with load applied. Not for use on airbags.
-
Product
DC Electronic Load
3310G Series（800W）
-
Has its own control and display panel, CC / CR / CV / CP / Dynamic modes, with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface
-
Product
Load Boards
-
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
Product
Programmable DC Electronic Load
IT8500+ Series
-
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications. They can be offered as multiple solutions according to customer's design and testing requirements.
-
Product
Load Tester for D Type Durometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.
-
Product
Beam Load Cell
EST-70
-
Technopark Automation & Control
The EST-70 Shear Beam Load Cell is commonly used on platform, hopper weighing and pallet weighing applications. It is low cost and available in capacities from 500 kg to 2000 kg.
-
Product
PXI 10 Banks of 16 Channel 1 Pole MUX
40-615-022-10/16/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
