Filter Results By:
Products
Applications
Manufacturers
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Accessories: Fixture
ICT I3070
View ICT i3070 fixture accessories ranging from fixture kits to vectorless test items like nanoVTEP. You can conveniently select items/parts to request for a Quick Quote.
-
product
Fixture Design
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
product
In-Circuit Fixtures
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
product
Automatic Fixture Removal
S96007B
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
product
Custom Fixtures
The shock and vibration fixture model BW-SV-3X3X3 is designed to accept up to 24 each of the TO-3 packages on each of the 6 axes and mount to the vibration shaker model BW-100C and Shock Tester model BW-E5000. The fixture is made of white derlin and measures 3”x3”x3”and weighs approximately 13 ounces. The fixture includes a white derlin cube with a 2 ¼” bolt circle and 4 10-32 x 3” cap screws.
-
product
Test Fixture Adapters for In-Circuit Test Fixtures
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
-
product
Mechanical Test Fixtures
MMI series man-machine interface
Designed to meet the needs of the most discerning customers and the latest market demands, our MMI series guarantees a natural posture for both the operator and the sitting position when performing the test on the adapter. The newly developed lever mechanism, which has been registered as a utility model, is specially adapted to the hand movement of its employee and ensures a heart-loving strain on the operator.
-
product
Functional Fixtures
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
product
Latch-on Test Fixtures
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
product
Fixture Building Software
FixGenius
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
product
Universal Test Fixture
CAM/GATE
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
product
Test Fixtures & Test Sets
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
MIPI Test Fixtures & Software
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
Custom Test Fixtures
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
product
Fixture Kit
MF300
Due to careful selection of materials, use of modern manufacturing techniques, and supplying the kit "flat packed" for end-user assembly, Merifix fixtures kits are inexpensive enough to be used in low-volume production and in engineering labs for programming and debug tasks, where traditional fixtures would be too expensive.
-
product
Universal Test Fixture
Series 48
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
