Loop Simulators
-
Product
SIMULATOR
458-LM-A8-18A
-
Simulates 26 AWG PIC as specified in ANSI T1.417Bandwidth DC to 18 MHzIdeal for testing ADSL, ADSL2, ADSL2+, ADSL2++, VDSL,VDSL2(supports up to Profile 17a) modems/DSLAMs8 channels per line moduleLoop lengths programmable from 0 to 15,000 ft in 1,000-ft incrementsPlugs into our Model 458-CC-16 (16-slot) or 458-3SLB (3-Slot)chassisChannel-to-Channel isolation up to 90 dB
-
Product
Loop Testing
-
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-SH
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can beused for measurement of DC and AC current, pulse currents etc. The output of thetransducer reflects the real wave of the current carrying conductor.
-
Product
Transistor-Level Defect Simulator
Tessent DefectSim
-
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
Product
LED DC Electronic Load Simulator
3340G Series（150W~300W）
-
Each 3340G Series module has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
Product
PCB Simulation Solutions for High-Performance Designs
HyperLynx
-
HyperLynx® offers a complete suite of analysis and verification software that meets the needs of PCB engineers at any point in the board design flow. Easy to use and integrate into your flow, HyperLynx equips PCB engineers to efficiently analyze, solve and verify critical requirements to avoid costly re-spins. Achieve greater innovation, faster time-to-market and decreased costs with HyperLynx.
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Analog Simulator
MPLAB® Mindi™
-
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
Solar Simulator
Unisim Compact Solar Simulator
-
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system.As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability.The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available).The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter.Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
8 Port T1/E1/PRI ISDN Simulator
SIM-8PRI
-
The most inexpensive ISDN simulator on the market. This unit has eight PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Solar Array Simulator DC Power Supply
62000H-S
-
Chroma Systems Solutions, Inc.
Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.
-
Product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Testing)
PA60Bi
-
PA60Bi is the panel-mounted power amplifier, which can produce 3-phase current, with maximum RMS phase current of 60A and maximum output power of 800VA, and 4-phase voltage, with maximum RMS phase voltage of 120V and maximum output power of 60VA.
-
Product
Floating Power FET moduleAmp Loop
PFM1010
-
The PFM1010 Module is a precision instrument capable of measuring all common DC parameters in a power MosFet as well as many of the AC parameters. This module uses some very innovative techniques to make it possible to measure parameters like Rdson down into the sub-million-ohm range.
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
One Core Loop Tester
-
DAMUL is an innovative and portable optical power checker accompanying 1-core loop back function. DAMUL can check SFP TX and RX power level by simply inserting SFP into it. If you use UPM (Universal SFP-typed Power checker Module) optionally provided, DAMUL can measure optical power. Also, when using SPM (SFP-typed Power checker Module) optionally provided, DAMUL can identify 18 CWDM wavelengths as well as its power automatically. DAMUL provide users high productivity for optical power checking work on fiber optic systems such as WDM-PON.
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
Time-Domain Electromagnetic Simulation
Meep
-
Massachusetts Institute of Technology
Meep is a free and open-source software package for electromagnetics simulation via the finite-difference time-domain (FDTD) method spanning a broad range of applications.
-
Product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Friction Flow Loop System
-
Friction Flow Loop System is used for testing the effects of friction reducers by circulating at high rates through different pipe diameters. Friction Loop designs vary based on the application required.
-
Product
Phase Locked Loop (PLL) Synthesizer & Translation Loop
-
ADI’s industry leading phase locked loop (PLL) synthesizer family features a variety of high performance, low jitter clock generation and distribution devices. The extensive, ever growing family includes over 100 products, optimized for high data rate, low jitter clocking applications. The portfolio features PLLs, PLL/VCOs, and distribution chips, designed for clocking applications where synchronization, clock distribution, and phase noise performance are all vitally important.
-
Product
OBD2/J1708/J1587 Simulator
DFLSOBD2
-
The OBD2/J1708/J1587 simulator is designed to simulate the truck or car''s ECU using OBD2- compatible protocols (7 protocols) and J1708/J1587 protocol (Total 8 protocols). It can monitor data packets on the vehicle data bus by RS232 of PC, and give some reasons of communication mistakes. It makes the developers easy for debugging their OBD2 or J1708/J1587 firmware.
-
Product
Multi-channel GPS Signal Simulator
MP6220
-
*Up to 8 channels support positioning test*Can also be used as a single channel
-
Product
Battery Cell Simulator
BCS-LABCAR
-
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Simulation and Testing Solutions
LMS
-
Siemens Digital Industries Software
LMS simulation and testing solutions help manufacturing companies manage the complexities of tomorrow’s product development by incorporating model-based mechatronic simulation and advanced testing solutions in the product development process. Our products and services tune into mission-critical engineering attributes – ranging from system dynamics, structural integrity and sound quality to durability, safety and power consumption.
-
Product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
-
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
Product
Motion Simulation
-
Exail's motion simulators are at the forefront of calibrating and testing inertial sensors, navigation systems, and optronic payloads across diverse applications, from traditional land vehicles and aircraft to emerging sectors like autonomous vehicles and wearables. With 60 years of expertise, Exail's rate tables deliver unparalleled performance, accuracy, and reliability, offering a cost-effective solution tailored to meet customer needs at every stage of product development. From concept to maintenance, Exail provides comprehensive support, ensuring the success of each project
