Insulation Resistance Meters
-
Product
Setaflash ‘Series 8’ Active-Cool (Corrosion Resisting)
6910
-
The Elcometer 6910 Setaflash ‘Series 8’ Active-Cool (Corrosion Resisting) offers the same feature as the Active Cool Closed Cup Tester but comes with a corrosion resisting insert in the cup for testing corrosive samples.
-
Product
Digital Insulation Tester
DIT-1020
-
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT-1020 is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage of 100 Volts DC, its short circuit current is less than 500uA.
-
Product
Ultrasonic Meters
E-Series
-
E-Series Ultrasonic water meters from Badger Meter use solid-state technology in a compact, totally encapsulated, weatherproof, and UV-resistant housing, suitable for residential and commercial applications. Equipped with an easy-to-read, 9-digit LCD display, the ultrasonic meter reports consumption, rate of flow, reverse-flow indication, and alarms. With no moving parts, the E-Series Ultrasonic meter improves reliability and has greater extended low flow accuracy compared to mechanical meters.
-
Product
Scale / Weight Meter
-
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
In-circuit ESR Meter
Capacitor Wizard
-
The Capacitor Wizard® finds bad capacitors IN CIRCUIT by measuring a capacitor's ESR (equivalent series resistance). A good capacitor should have very low ESR. Weak and bad capacitors have much higher ESR. The Capacitor Wizard® will SPEED UP YOUR REPAIR.
-
Product
SWR / Power Meters
SX240C
-
Dimensions:170Wx115Hx150DmmWeight:1350gFrequency range:S1 (1.8-54MHz) S2 (140-470MHz)Power display rating:30W/300W/3kW(HF band only)Accuracy of full scale:±10%(F.S.)
-
Product
Noise Dose Meters
-
Here you will find a full range with an industrial standard noise dose meter to suit every requirement. With the portable noise dose meter you can carry out measurements quickly to gain control of a situation or to set the device to take timed measurements. The noise dose meter is important for all industries, especially by using it as a mobile device which is able to assess office stress levels or street noise levels.Often problems arise from noisy neighbors or if bars and restaurants are in residential areas and produce noise levels after 10pm in excess of what local laws permit. We, of course, can assess which noise dose meter you require in relation to the issue you have and the relating laws. We also have microphone extension cords, tripods, calibrators and calibration certificates for most models of noise dose meter.
-
Product
Meter Test Switches
-
TESCO introduced the original Meter Test Switch in the early 1920’s. Today, TESCO’s line of Test Switches has been redesigned with the intention to combine the best features of tried and proven switching methods with improvements in materials and construction. All of the current carrying parts are bright tin plated to prevent corrosion. Good operating contact is assured on periodic meter tests, even when the switch has been idle for long periods of time in an unfavorable atmosphere.
-
Product
Clamp Meters
-
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Product
Wireless Meters
-
Digital Multimeter is loaded with the parameters and ranges HVACR professionals need for HVACR troubleshooting, plus it receives measurements wirelessly from any of the Fieldpiece Accessory Heads when connected to the wireless transmitter that''s included. You can now easily measure current, resistance, voltage, capacitance, frequency, continuity, and temperature either directly, or wirelessly from up to 75'' away.
-
Product
Clip-on Power Factor Meter & Watt Meter
-
Cambridge Instruments & Engineering Co.
Measurement of power factor in AC system on L.T. Circuits having higher current load without interrupting circuit.
-
Product
Ultra-High Resistance Scanner
6564
-
Ultra-High Resistance Scanner is the only Scanner capable of operating with measurements to 10 PΩ’s (1015) and at voltages to 1000 Vdc. The 6564 has world-leading isolation of 1017 with repeatable offsets above this resistance. Researchers and Metrologists can now easily and quickly automate single or multiple resistance measurements.
-
Product
Low Resistance Or Continuity Testing
-
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
Product
Ultraviolet Meter
UVR Series
-
UVR series is suitable to manage lamp of ultraviolet curing equipment, Also suitable to measure intensity of ultraviolet ray for sun light and lamp.
-
Product
Phase Angle Meter
-
Exceptionally fast response (up to 20 updates per second) and high accuracy for low frequencies, such as AC line frequency. A resolution of 1, 0.1 or 0.01 is user-selectable. Accuracy is 0.01% up to 100 Hz, 0.1% at 1 kHz, and 1% at 10 kHz.
-
Product
Wood Moisture Meters
-
Designed to measure the moisture content of wood, paper, plywood, and other wooden materials. This device classifies wood into four categories based on material density, and applies temperature compensation algorithm to ensure measurement accuracy.
-
Product
3 Wire (Digital) Earth Resistance Tester
2720 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
Product
Meter Test Station
WECO 8000
-
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
Product
Analog Hipot & Insulation Tester
KT-5000Pi
-
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
Product
Dynamic Gravity Meter
TAGS-7
-
TAGS-7 represents the latest development in a long line of LaCoste-based airborne gravity systems, stretching back to the first successful airborne gravity flights in 1958 and building on the success of the TAGS System. For over 50 years, LaCoste gravimeters have acquired hundreds of thousands of line kilometers of gravity data during academic, government, and commercial surveys. TAGS-7 blends the latest in GPS and data acquisition technology with the solid foundation of the LaCoste dynamic gravimeter.TAGS-7 is an upgrade to the TAGS-6 gravity meter, and is designed specifically for airborne operations. The system incorporates a time-tested, low-drift, zero-length-spring gravity sensor mounted on a gyro-stabilized gimbal platform. The sensor has a worldwide gravity measuring range (no reset necessary) of 500,000 milliGals.
-
Product
Light Meter
LI-250A
-
The LI-250A is a portable meter that displays the output from any LI-COR light sensor that has a cable terminated with a BNC connector. It shows instantaneous values or 15-second averages of values from a sensor.
-
Product
Moisture Meters
-
Moisture meters are used to measure the percentage of water in a given substance. This information can be used to determine if the material is ready for use, unexpectedly wet or dry, or otherwise in need of further inspection.
-
Product
Vibration Meters
-
Overall Vibration Meter and Electronic Stethoscope, display unit with electronics includes: (2) "AA" batteries, (1) Sensor Pak, (1) Carrying Case, (1) Stereo Headphones with 3.5 mm "MINI" PLUG, (1) Owners Manual.
-
Product
Digital Light Meters
-
A selection of digital light meters including the GM1010 & GM1020 light level meters
-
Product
Insulation Tester
CENTER 360
-
4 Digits LCD Display, Auto Range For MΩ & Ω, 40 Segments Analog Display, Test Hold Function For Easy Operation, Automatic Zero To Null Lead Resistance
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Thermistor Power Meter
N432A
-
Keysight N432A is the replacement for Keysight's legacy 432A analog thermistor power meter. The single-channel, average RF power meter operates with the Keysight 8478B and 478A thermistor mounts. The N432A-and-thermistor-mount pair is ideal for applications that require high measurement accuracy, particularly in metrology and calibration laboratory environments. The enhanced thermistor power meter comes with a digital color LCD display, and user-friendly front panel interface. Its built-in calibration factor table provides a more convenient and accurate method of storing calibration factors as compared to the old knob-turning approach of the 432A. The N432A is LXI compliant, and programmable via GPIB, USB and LAN.
-
Product
Digital Meter
-
Shijiazhuang Suin Instruments Co., Ltd.
A meter is any device that measures and may record an electrical or magnetic quantity, such as voltage or current.
-
Product
Digital Earth Resistance Testers
-
This groundmeter is designed for testing ground wire of electric power net, as well as earth voltage test in the fields of household electric power system and delectric appliance application.
