Vacuum Fixtures
actuate UUT typically PCB to bed of nails.
See Also: Fixtures, Test Fixtures, Mechanical Fixtures
-
Product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Emergency Battery Test Fixture
TA-60
-
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
Product
Vacuum, Module, Receiver, 90 Series, 2 Port Positions
510104260
Receiver Module
Primary mating module 510108242. (May mate with other ITA modules, as well.)
-
Product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
-
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
Custom Fixtures
-
The shock and vibration fixture model BW-SV-3X3X3 is designed to accept up to 24 each of the TO-3 packages on each of the 6 axes and mount to the vibration shaker model BW-100C and Shock Tester model BW-E5000. The fixture is made of white derlin and measures 3”x3”x3”and weighs approximately 13 ounces. The fixture includes a white derlin cube with a 2 ¼” bolt circle and 4 10-32 x 3” cap screws.
-
Product
Manual Test Press Fixture
750/752 Series
-
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.
-
Product
Thermal Vacuum Heater Power
-
AMETEK Programmable Power, Inc.
Provides programmable power to heater elements
-
Product
In-Circuit Test Fixtures
-
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
Product
Manual Fixture Kit
230376 – CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Vacuum Pressure Sensors
-
MKS, Granville-Phillips® Vacuum Gauges & Sensors cover a broad spectrum of vacuum measurement solutions.
-
Product
Vacuum Leak Tester
MFY-CM
-
Saicheng Vacuum Leak Tester (also called Leak Detector, Leak Test Apparatus) is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
Clamshell Type Mechanical Fixtures
Series 34
-
The Series 34 Test Kits are a smaller 4 block version of the GR2270
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
Walk In Vacuum Climatic Test Chamber
-
WEIBER Vacuum Chambers are rigid enclosures from which air and other gases are removed by avacuum pump.This results in a low pressure environment within the chamber, commonly referred to as avacuum. A vacuum environment allows researchers to conduct physical experiments or to test mechanical devices which must operate inouter space(for example) or for processes such as vacuum drying or vacuum coating.
-
Product
Custom Designed Test Fixtures
-
We specialize in automated test systems for both RF and digital devices, modules and systems. Please call to discuss your test requirements.
-
Product
Headphone Test Fixture
AEC206
-
The Larson Davis Model AEC206 Binaural Test Fixture is the tool for testing supra-aural, circumaural, supra-concha, intraconcha, and insert-type headphones. Preassembled with IEC 60318-4 (711) occluded-ear simulators and TEDS compatible preamplifiers that provide electronic calibration information, the Model AEC206 is user-friendly and easy to learn. Additionally, calibration is a simple process—a custom adapter is included for the Model CAL250 acoustic calibrator or similar device.
-
Product
ICT/FCT-Fixtures (Large IF)
GenRad CK-2-228X
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
System Test Fixture
-
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
Product
EBIRST 8-pin Male Power D-type Termination Fixture
93-012-103
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Vacuum Handling Systems
-
RECIF Technologies history started in 1982 offering its first wafer handling solution: Vacuum handling Systems.Based on this historical technical mastery, Recif Technologies provides today a full range of single wafer manual vacuum handling solutions adapted to our customers’ and current Semiconductor industry’s’ requirements.
-
Product
Functional Test Fixtures
-
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
Product
Vacuum Chambers
CV 400/CV 250
-
The CV 250 and CV 400 are vacuum chambers for altitude flight simulation for avionics instruments such as altimeters, rate of climb indicators and all non pressurised equipment. They are fitted with pneumatic and electric connectors and a quick locking door.
-
Product
Custom PCB Test Fixtures
-
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
Product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
-
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
-
Product
MIPI Test Fixtures and Tools
-
In order to support our MIPI test services, UNH-IOL has designed and created test fixtures and software tools to aid in performing C-PHY, D-PHY, DSI, and CSI-2 testing.
-
Product
Magnetizing Fixtures
-
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
