Combiners
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
JTAG Boundary-Scan I/O Modules
SCANIO Family
-
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
Product
Handheld Tachometers
-
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
Product
IR/Green/UV Subnanosecond Laser
SN Series
-
The SN Series lasers combine ultra-fast pulse control with high pulse energy, delivering exceptional precision for laser scribing, glass cutting, and medical microstructuring. With adjustable pulse widths from 100ps to 5ns, they enable advanced material processing, time-resolved spectroscopy, and imaging applications. Designed for reliability and flexibility, the SN Series ensures high-speed, high-accuracy results for cutting-edge industrial and scientific needs.
-
Product
VB Build-A-Box
-
The VB Series, Build a Box provides a solution for any combinations of signal transport over fiber. With the VB-10 (10 card slots), VB- 6 (6 card slots), VB-4 (4 card slots), a unit can be created to your specification by populating the case with any configuration of VB-Cards. Each card’s I/O can be sent or received over its own disparate fiber, or all signals in the box can be multiplexed onto just one fiber. Inherently portable, each unit is ready for field applications or can be rack-mounted with optional Rack Mount kits.
-
Product
Chip Inspection System
GEN3000T
-
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
Product
Modular Power
RFP AC Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Software Modules
-
Verisurf Solution Suites consist of combinations of specialized application modules. All Solution Suites require the powerful CAD module.
-
Product
GPS Modules
-
A GPS module is a receiver that uses signals from satellites to determine location and time, while a GPS modem is a more complete device that combines a GPS receiver with a modem (like a GSM or cellular modem) to send that location data over a network.
-
Product
SMARC® Short Size Module with Intel Atom® E3900 Series, Pentium™ N4200 or Celeron™ N3350 Processor (codename: Apollo Lake)
LEC-AL
Computer on Module
The LEC-AL Computer-On-Module (COM) combines the SMARC® 2.0 standard with the latest Intel Atom® E-Series and Pentium® and Celeron® N-series System-on-Chips (SoCs), providing ideal solutions for low power consumption and high performance requirements. The module provides the high integration, high performance, low power, and ruggedness favored by Internet- of-Things (IoT) applications such as retail transactional clients, digital signage, and in-vehicle infotainment systems. The LEC-AL module utilizes the latest Intel E-series and N-series SoCs, which are based on the Intel 64 Architecture, the new HD Graphics 500/505 engine, and a faster, 4-vector image processing unit. The SoCs are manufactured on Intel's industry-leading, tri-gate 14nm process, improving system performance by supporting more than 4 GB of both virtual and physical memory.
-
Product
EXG X-Series Microwave Analog Signal Generator, 9 kHz to 40 GHz
N5173B
Signal Generator
Balance budget & performance to address parametric testing of microwave components & receiversPerform LO up conversion for microwave backhaul links or CW blocking for receiver testingMaximize test throughput with 600-s frequency switchingCharacterize microwave filters & amplifiers with the best combination of output power, low harmonics & full step attenuationUse as a high-stability system reference: the standard high-performance OCXO has an aging rate of 5x10-10 parts/day
-
Product
Autoranging System DC Power Supply, 80 V, 510 A, 15000 W, 400 VAC
N8951A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
Vector Signal Analyzers
Vector Signal Analyzer
Vector signal analyzers combine superheterodyne technology with high speed ADCs and other DSP technologies to provide fast FFT-based, high-resolution in-channel spectrum measurements, demodulation, and advanced time-domain analysis. A vector signal analyzer is especially useful for characterizing complex burst, transient, or modulated signals in aerospace & defense, radar, wireless communications, and avionics.
-
Product
C-Band 1510nm BWDM
WD1510
-
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1510 WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to WDM network to achieve the combination and separation of C-Band 1510nm (±10nm, monitor and control channel).
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
Compact Case 20 L | Comfort | 300 mm
20C-401-300
-
The Compact Case 20 combines flexibility, practicability and intelligent design. Available in four different sizes and three different finishing options. Optionally also with EMC protection.
-
Product
Enhanced & Flexible Ports - SmartFlex
-
4G cellular routers with enhanced & flexible ports number including combinations of Ethernet 10/100, RS232, RS485.
-
Product
Data Logger with GSM/GPRS Module
HD33M-MB.2
-
GSM/GPRS data logger. RS485 MODBUS-RTU input, additional contact input for rain gauge. Great to combine with HD52.3D and HD51.3D series anemometers!
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
cDAQ-9171, 1‑Slot, USB CompactDAQ Chassis
781425-01
Chassis
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9171 also has four 32‑bit general-purpose counters/timers that you can access through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Pyrometer with Spotfinder
thermoMETER TIM 8
-
The thermoMETER TIM 8 combines the advantages of a robust pyrometer with a thermal imaging camera. Due to its extremely compact size, it can also be integrated into machines and production lines. The spotfinder function enables precise temperature measurements with automatic sensor adjustment. In addition, remote focusing of the lens is possible via a motorized focus. This intelligent spotfinder pyrometer is used in automation, machine building and plant monitoring.
-
Product
RF Device Tester
RF ITS
-
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
-
Product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Dial Weight Dynamometers
-
The most important characteristic of any measurement instrument is repeatability and accuracy. The Magtrol Dial Weight Dynamometer uses the combination of a Hysteresis Brake and gravity to insure constant, reliable results. The brake torque rise is directly proportional to applied current
-
Product
Fully-Programmable Automatic Stencil Printer
MC1400
-
MC1400 Automatic stencil printer MC1400's automatic dual-vision alignment system ensures accuracy while the printer's linear-guided movements and vertical stencil separation provide high precision and repeatability, a combination that results in ultra-fine-pitch printing capability for component pitches down to 0.3 mm (12 mil). With quick setup and changeover, thanks to the flexible mounting table, MC1400 stencil printer easily keeps pace with medium to high volume production lines and is well-suited to precision batch printing.
-
Product
PXI-4110, 3-Channel, 20 V, 1 A, 9 W, PXI Programmable Power Supply
779647-10
Programmable Power Supply
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
Product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
External Controller
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
Product
3D Optical Profiler
Nexview™ NX2
-
Designed for the most demanding applications, the Nexview™ NX2 3D optical profiler combines exceptional precision, advanced algorithms, application flexibility, and automation into a single package that represents ZYGO's most advanced Coherence Scanning Interferometric (CSI) profiler.
-
Product
40GHz Single Channel MW Benchtop Signal Generator
LXS4091B
Signal Generator
The LSX4091B is a 40GHz Single Channel Microwave Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
