Transmittance
-
Product
Dewpoint Transmitters
-
Incorporated into the design of these transmitters are advanced electronics allowing for a power supply varying from 18 to 30V DC and are configured to output a linear, isolated, 4-20mA signal for the chosen range.
-
Product
Oxygen Measurement Analyzers, Transmitters & Sensors
-
Precise oxygen measurement is critical for processes in many industries, ranging from the purity of industrial gases and protecting against leaks in glove boxes to monitoring flue gas for optimum combustion efficiency.
-
Product
Multivariable Transmitters
-
The Multivariable transmitter measures and calculates the mass flow as a function of differential pressure DP as well as absolute pressure and the temperature. Therefore it should be used whenever DP flow measurement needs a compensation of temperature and pressure. The main advantage is to have just one single device in the field instead of several transmitters and a mass flow calculator.
-
Product
Vantage PRO2 Davis
6152 & 6152C
-
*Refresh Rate – A packet of data is sent from the outdoor transmitter to the receiver every 2 1/2 seconds! This means when you look out the window and see the wind blowing, the weather station will reflect it almost immediately.*Transmission Distance (wireless models) – The first in its consumer price range to use frequency hopping spread spectrum radio technology, the Vantage Pro2 can transmit and receive data up to 1000′ (300 m) line of sight. This is a much greater distance than most other weather stations. This technology also provides improved reception through multiple walls and greater immunity from RF interference.
-
Product
Humidity Calibration Set
-
The humidity transmitters as all other measuring instrumentsshall be periodically checked and eventually adjusted. The most simple solution for this purpose is the E+E calibrationset.
-
Product
Panel Mounting Conductivity Transmitter
DO9786T-R1
-
output of a conductivity electrode with temperature compensation into a 4÷20 mA signal.
-
Product
Frequency Counter, 30MHz to 800MHz, 500MHz to 2.8GHz, 7 Digits
72-7390
-
Rugged instrument is smaller than a deck of cards, yet provides frequency measurement of digital, on/off keying and analog signals from 30MHz to 2.8GHz. It is perfect for displaying the output of two–way radio equipment, analog and digital cell phones, RF remote controls and many other items. Internal vibrator alert also makes this an outstanding device for detecting transmitters in counter–surveillance applications
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Shield Level / Pathloss Equipment
PAMS & PAMS-C
-
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
Product
Power Amplifier, RF
-
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
Product
FM Tokenless Transmitter & Receiver
MS 1522
-
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
Product
Standalone ILINK Transmitter And Receiver
SPC-ILINK
-
SPC-ILINK, a standalone accessory for SPC-800 monitors, uses HDBase-T for long-range video and USB control, supporting 100m video with 4K/8K ESD.
-
Product
Temperature Transmitter and Regulator
H0430
-
Built-in temperature sensor.Temperature transmitter is equipped with three two-state inputs for detection of two-state signals - e.g. power presence, water, smoke, airflow, glass break detection, door contact.
-
Product
Guided Wave Radar Level Transmitters
LWT Series
-
For high-accuracy, reliable measurements even in harsh conditions.Using radar frequencies, guided in a probe going into the monitored vessel, guided-wave radar level measurement provides continuous, reliable measurements with high accuracy. The radar wave being guided by the probe, the wave energy remains high which allows measurement even in harsh conditions.
-
Product
Force Transmitter
LKVE/i
-
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
Product
Optical Switch Boxes
-
An optical switch box is needed so that automated test platforms can permit the system to measure the performance of transmitters and receivers at multiple wavelengths or channels. The MLO4034 Optical Switch Box incorporates a WDM demultiplexer, integrated power meters, variable optical attenuators, and optical switches to form an integrated switch matrix. It enables receivers and transmitters to be tested at up to four wavelengths or channels.
-
Product
Cable Detectors
-
The cable detector makes it easier to find cables in the wall and cable ducts. Here, an adapter or carrier signal from the transmitter is modulated by means of crocodile clips or the adapter to one end of the cable. The other end of the cable can then be found quickly and precisely with the receiver without contact or having to strip the cable insulation. Two-core cables can also be exactly identified in telecommunication and network technology.
-
Product
Microwave Transmitter
LTX-310B
-
LTX-310B is a self-contained microwave transmitter for use with the LRX-310B receiver. The output is pulse modulated to identify one of 36 channels arranged in six groups of six. The group is set at the factory and you can select one of the six channels in that group from an external rotary switch.
-
Product
CO2 Concentration and Temperature Transmitter
T8448
-
CO2 concentration and temperature transmitter with serial RS485 output is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
Product
Microprocessors & Peripherals
-
Renesas offers MIL-STD-883-compliant microprocessors and a CMOS universal asynchronous receiver transmitter (UART) that are qualified to QML Class Q military standards.
-
Product
RTD Alarm Setter Transmitter
Model TAR
-
Kusam Electrical Industries Limited
• 4 Digits Display For Input Signal:100.0 - 400.0 • Display - 100~400 °C / 100~700 °F • Output Signals Are Programmable. • Ultra-thin Dimension, 27mm width. • Non-Combustible PC Case .DIN Rail or Wall Mounting. • High Dielectric Strength ( AC 2KV / Min , Input / Output / Power )
-
Product
Differential Pressure Transmitter
616W
-
Positive, negative and differential pressures can be measured within a full span accuracy of ±0.25 with the Series 616W Differential Pressure Transmitter. Units are enclosed in a polycarbonate case, rated NEMA 4X (IP66) and operate by sensing the pressure of air and compatible gases then sending a standard 4-20 mA output signal.
-
Product
Cable Locator
CL 20
-
Cable fault location with the BAUR CL 20. The CL 20 cable locator comprising a transmitter and a receiver is used to determine the exact location of cables and metal pipes. The ability to determine laying depths of up to 4.5 m and to measure signal currents at the touch of a button allows you to obtain reliable information on the position of the cable within the shortest time.* Fast and exact location of position and laying depth of cables* Intuitive operation – no special measurement knowledge required* Lightweight and manageable
-
Product
Modbus Transmitter for Photometers
LPPHOTS
-
with RS485 MODBUS-RTU output for photometric probes
-
Product
Universal, Dual Input, High Performance HART Temperature Transmitter
SEM310 MKII
-
The SEM310 is a universal programmable HART temperature transmitter which accepts most commonly used Pt100, thermocouple, mV and slide-wire sensors and generates an industry standard (4 to 20) mA transmission signal
-
Product
Photometric Radiometric Transmitters
HD2021T Series
-
The serie HD2021T allows to convert photometric and radiometric quantities, such as illuminance (Lux) and irradiance (W/m²) in the UVA, UVB, UVC spectral regions and in the 400 … 1050nm band, into a 0 …10Vdc voltage signal. The series is suitable to be installed either indoor and outdoor.
-
Product
Pneumatic Test Pump Kit
700HPPK
-
The Fluke Calibration 700HPPK Pneumatic Test Pump Kit generates and adjusts pneumatic pressures up to 21 MPa (3000 psi), without requiring a nitrogen bottle or other external pressure supply. It supplies pressure to devices under test (DUTs) that include transmitters, controllers, pilots, digital and analog gauges, and more. It’s the perfect solution for generating high pressure in the field, where conditions and operating surfaces can vary. The 700HPPK is the ideal choice for calibration technicians, test engineers, and instrument technicians working in industries like natural gas transmission and distribution, process, aerospace and defense, who need a simple-to-use, safe and portable pressure source that they can depend on in a wide variety of conditions.
-
Product
Suitable For RTD Sensors Approved To ATEX And IECEx Standards
TTR200X -
-
The TTR200X is our mid range transmitter for RTD or Slidewire sensors approved to ATEX and IECEx standards. It can accept many different types of RTD sensor such as Pt100, 500, 1000 etc and slidewire sensors up to 100K Ohm
-
Product
Ultrasonic Level Transmitter
USonic
-
The Drexelbrook family of Ultrasonic technology level products offers an affordable two wire and line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.Measurements of level, distance, volume and open channel flow is easily configured through the menu driven display. The Usonic level transmitter is offered with a two wire 4-20 mA, Hart output signal and is suitable for all Class I Div. 1, Zone 0, I.S. or XP locations. The bench configuration eliminates the need to move process material levels for calibration.
-
Product
Meteorological Sensors
-
Automatic Weather Station, Wind Speed Sensor, Air Temperature Sensor, MIRA Visibility Sensor, Wind Direction Sensor, Air Pressure Sensor, Barometric Pressure Transmitter, Solar Radiation Sensor.
