Gel Cell Battery
-
Product
Standard Shackle Load Cell
SS-3.0
-
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel
41-752A-001
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Battery Testing Equipment
-
Mainly for battery testing in lab,such as 5V1mA, 5V10mA, 5V50mA,5V100mA, 5V1A,5V3A,5V6A,5V10A
-
Product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
-
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
Product
CTEK Multi US 25000 Battery Charger
56-674
-
CTEK MULTI US 25000 is an 8-step, fully automatic primary switch mode battery charger. A powerful charger for 12V batteries that require rapid charging such as in garages, RV’s, boats and of course cars. Unlike old traditional battery chargers CTEK chargers are designed with focus on simplicity, safety and flexibility.
-
Product
Development Platform for Battery Operated IoT Applications
Thunderboard Sense
-
Thunderboard Sense is a small and feature packed development platform for battery operated IoT applications. The mobile app enables a quick proof of concept of cloud connected sensors. The multi-protocol radio combined with a broad selection of on-board sensors, make the Thunderboard Sense an excellent platform to develop and prototype a wide range of battery powered IoT applications.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
Miniature, Battery Powered, Stand Alone Pressure and Temperature Data Logger
PRTemp101A
-
The PRTemp101 is a miniature, battery powered, stand alone pressure and temperature data logger. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged.
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
-
Product
Beam Directional Power Supply Battery 40 to 120 kV
CP120B
-
This ultra-light, compact and battery operated constant potential portable X-Ray generator is the perfect tool for specific NDT applications that require repetitive short exposures. Its versatility also makes it the ideal piece of equipment for security applications. In fact, in combination with the FLATSCAN15, the FLATSCAN30 and other digital X-Ray detectors, the CP120B will – thanks to its small focal spot and constant potential X-Ray output – enhance image quality and definitely contribute to a reduced exposure time.
-
Product
5V30A High Current Lithium Battery Tester
TOB-BTS-5V30A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels High Current Lithium Battery Tester For Power Battery Performance Detection
-
Product
Fatigue Rated Low Profile Cells
-
Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
-
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
System Controllers & Battery Monitors
-
UNIPOWER System Controllers & Battery Monitors provide battery management functionality for the Aspiro, Guardian and Sageon DC Power Systems. The proprietary PowCom software enbles the user to monitor multiple Aspiro or Guardian systems at different locations using a highly intuitive GUI. SageView software provides similar fucntionality for Sageon systems and also works with the standalone Sageon Shield battery monitor.
-
Product
OEM Weigh Cells
-
Our weigh cells feature electromagnetic force compensation, strain-gauge type load cells, and electronic modules for various scenarios.
-
Product
Load Cell Power Supply
MODEL PSMR
-
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
Product
CTEK MXS 5.0 Battery Charger
40-206
-
The MXS 5.0 offers a unique eight-step approach to battery care. Fully automatic microprocessor controlled charger with built-in automatic temperature sensor features a unique combination of advanced charging modes and makes the new MXS 5.0 the fastest, most effective and versatile consumer charger CTEK has ever made. Alligator Clamps and Eyelets included.
-
Product
Battery Chargers
-
DC Battery ChargersStep-Up & Step-Down DC Source Chargers and Equalizers These units provide up to 600 watts to charge a 12V or 24 V battery systems (1 or 2 banks) from a 12, 24, 32 or 36 volt source. The single-board design incorporates state-of-the-art switch mode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. All Series are capable of charging up to two independent banks of batteries.
-
Product
In-Line Light I-V Testing for Solar Cells
FCT-750
-
In-line, light I-V and Suns-Voc measurements in a single flash at 2400 units per hour. Capability to accurately measure high-efficiency conventional or backside-contact solar cells.
-
Product
Solar Cell Simulation
Setfos
-
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
Product
Battery Ground Detector
BGD
-
Battery Ground Detectors supply contact closures for alarm indications at precise ground fault resistance settings.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Battery Checker
SK-8551
-
Total condition check for 12V (24V) batteries. (Truck, Marine, Industry etc.)Battery check, Engine start performance, Charging system tests.
-
Product
SOLAR CELL TESTER
-
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
Product
Battery Load Banks
-
Kongter Test & Measurement Co., Limited
Kongter offers many different models of battery load units for real capacity test in various industries. With our customized solution, users of different applications will find their exact models as per their needs. With its optional DAC (Data Acquisition Case), you could easily monitor voltage of each cell on PC during battery discharge test.
-
Product
Fixed Batteries (Constant Function)
-
Lifasa - International Capacitors, SA
Fixed compensation equipment has different variants depending on the type of enclosure / support and the configuration of the equipment (type of capacitor).
-
Product
olar Cells and Modules Online Measurement System
PV-LIT
-
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
Product
CTEK US 0.8 Battery Charger
56-865
-
US 0.8 is CTEK’s smallest 12 V charger. It offers state of the art technology and is perfect for charging smaller 12 V batteries that can be found in motorcycles, jet skis, ATVs and lawnmowers. It is also suitable for maintenance charging “normal- sized” batteries such as car batteries.The unique display allows the user to follow the entire charging process. The US 0.8 is a compact and fully automatic 6-step charger for 12 V batteries from 1.2–32 Ah and is suitable for maintenance charging up to 100 Ah. The US 0.8 is splash and dust proof, delivers 0.8 A and is designed to protect vehicle electronics. It is non-sparking, reverse polarity protected and shortcircuit proof. The US 0.8 is delivered with 5-year warranty.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
