Voltage Preamplifiers
-
Product
Voltage Sag Generator
SKS-1120GTA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
High Voltage Probe Meters
-
Shanghai Beha Electronics Co., Ltd.
*High voltage test probe *is a high voltage probe that is used with Oscilloscope● Attenuation Ratio: 1000:1*Measuring range: AC 20KV/DC 30KV
-
Product
Thin Film Chip Resistors, High Voltage Type
-
Panasonic Industrial Devices Sales Company of America
Thin Film Chip Resistors, High Voltage Type by Panasonic
-
Product
High Voltage Probe: Single-Ended
-
A high voltage single-ended probe is typically used for measuring ground referenced signals up to 40 kV. However, some single-ended probes are designed for oscilloscopes with isolated or floating inputs for measurements that are not ground referenced. Users should select probes with a low input capacitance specification (< 4 pF) to minimize the probe’s loading effect on the circuit because a probe with lower input capacitance will offer higher input impedance at higher frequencies.
-
Product
DC Voltage Sensors
-
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
Product
Closed-loop Ionizer Controllers For Multichannel Voltage Detection
Novx 3352/3362
-
Simco-Ion’s Novx brand of Passive (Model 3352) and Active (Model 3362) Multi-fan Closed-loop Ionizer Controllers provide the capability to simultaneously detect, measure, record and monitor electrostatic voltages in multiple locations. The versatile antennas used with these systems allow their use in a variety of applications including monitoring sensitive workstations, in-tool voltages, or ionizer performance with the option of closed-loop control to select ionizer products.
-
-
Product
voltage controlled crystal oscillator
VCXO
-
A VCXO (Voltage Controlled Crystal Oscillator) is a crystal oscillator the output frequency of which is controlled by adding an external control voltage via a frequency control input on a variable capacitance component such as a varactor diode connected in parallel to a load capacitance (CL). Epson VCXOs are divided into two types according to Voltage-Frequency (V-F) characteristic slopes depending on the AFC (Automatic Frequency Control) input configuration of the VCXO. One is a VCXO with a positive V-F slope and the other is a VCXO with a negative V-F slope. Please note that the input voltage of a control circuit will vary according to the individual type, as shown in Figs. 3 and 4. Epson's VCXOs are capable of either, depending on the customer's preference. Epson's VCXOs have been increasingly used for broader applications such as slave oscillators in phased-lock loops, or frequency modulators. Among the above types, a VCXO combined with a TCXO is called a VC-TCXO , respectively. These components have the merit of delicately controlling their output frequency electrically.
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 23-Channel, 1-Pole
40-321-108-HI
Multiplexer Module
The 40-321-108-HI (PXI) and 42-321-108-HI (PXIe) are dual 23-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
40-321-103-HI
Multiplexer Module
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-024-HI
Programmable Resistor Module
The 40-230-024-HI (PXI) and 42-230-024-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 6.97kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe
T3HVD1500-200
Differential Probe
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-123-HI
Programmable Resistor Module
The 40-230-123-HI (PXI) and 42-230-123-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
SPD High, Medium, and Low Voltage TOV Test Equipment
-
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems part 1: Performance requirements and testing methods)TOV fault test equipment1. Three-phase isolation test transformer2. Single-phase test transformer3. Low voltage switchgear4. Power controller5. Test voltage and current measurement6. Sample box
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-250-HI
Programmable Resistor Module
The 40-230-250-HI (PXI) and 42-230-250-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Digital Clamp Current Tester For High Voltage
HCL-36UX
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Display measurement value on your smartphone through blue-tooth connecting.・Measurement value can be kept in the our cloud server.・In addition to measured values, location registration by GPS, temperature, date and time can also be saved.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-022-HI
Programmable Resistor Module
The 40-230-022-HI (PXI) and 42-230-022-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching - 20xSPST Plugin Module
65-233-703-HI
General Purpose Relay Module
The 65-233-703-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 7 kV. Switch arrays are created by populating the 65-200-002 scalable chassis with plug-in modules that provide access to the switches on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the number of switches.
-
Product
Precision SOT-23 FGA™ Voltage References
X60003
-
The X60003 FGA™ voltage references is a very high precision analog voltage reference fabricated in Renesas' proprietary Floating Gate Analog technology, which achieves superior levels of performance when compared to conventional band gap, buried zener or XFET™ technologies.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-315-HI
Programmable Resistor Module
The 40-230-315-HI (PXI) and 42-230-315-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 925Ω with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-243-HI
Programmable Resistor Module
The 40-230-243-HI (PXI) and 42-230-243-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 770kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Additional Products: Standard Voltage 50 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
High Voltage Breakdown Tester
Model HV-100B
-
Laxtronics Instruments & Controls Pvt. Ltd
DC Output: 0 to 10 Kilo Volts continuously variable, AC Output: 0 to 5 Kilo Volts continuously Variable, Current Limit: 0 t
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-322-HI
Programmable Resistor Module
The 40-230-322-HI (PXI) and 42-230-322-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Standard Voltage 9 Pin D-Type Connector Blocks for Pickering Products
-
The connector blocks below are suitable to use with Pickering cards and modules that utilize a standard voltage 9-pin D-type connector.
-
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
Voltage Probes (Power Line Interference Probe)
Emissions
-
The Voltage Probe requirement is covered by our PLIP (Power Line Interference Probe). This fully meets the requirements of CISPR16, but has additional features: Fully galvanic isolation between input and output (>1kV), for the safety of operator and analyser. hrouded safety clips for attachment to the line to be measured. Filtered frequency response matched to Band A and B. Current limiting on the output. Visual indication of high voltage input
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-320-HI
Programmable Resistor Module
The 40-230-320-HI (PXI) and 42-230-320-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
