Emulator Adapters
-
Product
Passive XMC-to-PCI Express Adapter
5934
-
The Technobox, Inc. P/N 5934 is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
Sensor Signal Emulator
-
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
Product
Hand Adapters / Special Adaptations
-
*Hand adapters*Combi adapters*Service adapters*Rigging harnesses*Hand over adapters for engine test benches*Cockpit test systems*Special test benches ...*For every adaptation job the fitting adapter - application specific, reliable, robust with threaded and spring loaded contact pins.
-
Product
Battery Emulator And Profiler
E36731A
Battery Simulator
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
NI-5742, 16-Bit, 1 MS/s, 32-Channel Signal Generator Adapter Module for FlexRIO
782865-01
Signal Generator
The NI‑5742 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5742 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5742, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
PCB Adapter, Receiver, SIM, VTAC, 16 Positions, 6 Slots, to (1) Cat6
510170105
PCB Adapter (Receiver)
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules. Please note this part is too wide for use in multiple adjacent slots (for more information, please reference the attached drawing).
-
Product
Adapters
-
We have more than 1000 types of coaxial adapters on the shelf for immediate delivery; more than 200,000 coaxial adapters total. SMA, Standard N, SMP, TNC, BNC etc adapters are built to M39012, Mil-STD883 (Interface) & MIL-G-45204 or ASTM B488(plating). 2.4mm, 2.92mm, 1.85mm, 1.0mm, 7/16, 3.5mm, Precision N, Precision TNC, & 4.3/10 adapters are built to P287. 4,1/9.5 adapters are built to IEC standards. There are a few popular coaxial adapters for which we're not aware of a standard; u.fl etc. Mini DIN adapters are in stock.
-
Product
Test Adapters / Aeroflex Test System
52xx / 5300
-
We develop and manufacture test adapters for your existing interface including documentation and test program
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
Emulates Atmel T89C51RD2 in 68-PLCC package
FE-51RD2\68P
-
* Emulates Atmel T89C51RD2 in 68-PLCC package * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
PCIe Multi-Terminal Emulator
Sy629PCIe-BPTE
-
The Sy629PCIe-BPTE card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the approved Basic Protocol. This product also offers enhanced facilities to enable a user to insert transmission errors onto the bus and detect and report errors in received messages.
-
-
Product
Adapter, 1.0 Mm (m) To 1.0 Mm (m), DC To 120 GHz
Y1910A
-
Provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
Product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281B
-
The Keysight P281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
ITA, G2, 2 Module With 10 Module Enclosure And Adapter Plate, With Protective Cover
410120120
ITA
This ITA, Adapter Plate and Enclosure package provides an opportunity for customization and is an alternative to the ITA with removable cover. Protective cover is also included.
-
Product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 2 Slots, Texas Instruments PCI1520 Chipset
P222-TI1520
-
The PCI to 2-slot PCMCIA/CardBus PC-Card adapter supports 3.3V & 5V PC-cards (PCMCIA/Cardbus) simultaneously. Hot-swap PCMCIA/Cardbus PC-cards without powering off the system. 2 independent icons in MY COMPUTER. The adapter is quick & easy to install, allowing PC-card devices to be used in any desktop or tower PC.
-
-
Product
USB to VGA Adapter with Retention, USB Type-C Male to VGA Female, 0.5m
143557-0R5
USB Connector
24-Pin USB-C 3.1 Male to 15-Pin VGA Female, 0.5 m Display Cable - The VGA15F-USB24M Cable for CompactDAQ and CompactRIO controllers and chassis features a male USB-C connector and a female VGA connector.
-
Product
EPC Emulators
-
The EPC Emulators consist of the MME Emulator, HSS Emulator, SGW Emulator, PDN-GW Emulator, and the PCRF Emulator, which can be used together to simulate the complete LTE Packet Core or individually to create a combination of real and simulated Core Network elements. These Emulators includes all the network interfaces and implements all the communication protocols required for core network equipment to operate in an LTE/SAE network.
-
Product
Passive XMC-to-PCI Express Adapter
6067
-
The Technobox, Inc. P/N 6067 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O. JTAG signals are brought out to headers allowing users the option of connecting the two JTAG ports.
-
Product
Test Adapter / Vacuum Adapter
-
GPS testing technology offers a large selection of vacuum adapters. The support with vacuum (negative pressure) results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.We recommend the use of vacuum hoods or, if contact is required on both sides, our vacuum swivel hood.
-
Product
Ethernet Adapter Supporting up to Twenty ARINC-429 Channels in Any Combination
ES-9810/A0 (RUNET II)
-
The EXC-9810/Ax is an Ethernet adapter supporting up to twenty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC-429 bus, both in the lab and in the field.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention. The EXC-9810 supports up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-9810/Ax adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher). Please see multi protocol 8000 modules for additional information on protocols that can be added to this card.
-
Product
Adapter, 2.4 mm (f) to 2.4 mm (f), DC to 50 GHz
11900B
-
The Keysight 11900B is a metrology-grade, 2.4 mm female to 2.4 mm female adapter with dc to 50 GHz operation.
-
Product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-02
Digitizer
he NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Signal Contact (Receiver)
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Dsub25 To 5 SMB Adapter
PX0106A
-
Keysight's PX0106A Adapter converts Dsub25 outputs to five SMB outputs with path through connection. It supports the Keysight M9614/15A.
-
Product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
-
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
Product
Coax, Contact, Receiver, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102135
Contact Adapter (Receiver)
Primary mating contact 610102134. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination 3.5mm compatibleInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mΩ max. center conductor3 mΩ max. shieldCable Specifications 3.5mm compatible Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MΩ min.
