Product

ANSI X3.28 to Modbus RTU Converter

Model 2399

-

ICS Electronics

Model 2399 - ICS Electronics

* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.

Product

High-Reliability Voltage Controlled Oscillators

-

Fairview Microwave Inc.

Fairview Microwave Inc.

16 Models with Frequency Bands ranging from 10 MHz to 4350 MHz. 0.5" Hermetically Sealed Surface Mount Package. 50 Ohm Internal Matching. Designed to meet MIL-STD-883 and MIL-STD-202 Test Conditions. Wide Voltage Tuning Range from 0.5V to 20V. Phase Noise as low as -120 dBc/Hz @ 10 KHz offset. 2nd Harmonics as low as -25 dBc. RoHS and REACH Compliant. All models are EAR99. These products are used in military electronics, SATCOM, test and measurement and wireless communications.

Product

Voltage Input Device For FieldDAQ

-

NI

NI

The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.

Product

DC to DC Voltage Regulator

HVDR-15

-

Astro Flight Inc.

HVDR-15 - Astro Flight Inc.

The HVDR-15 is a high efficiency, high voltage step down DC to DC voltage regulator. Input voltage can be as high as 110VDC. Up to three output voltages can be pre-configured to allow up to 1A or 3A of output current. The HVDR-15 features over voltage, over current, and over temperature protection. It is offered in one, two, or three output voltage versions making it a very efficient and flexible platform for many applications.

Product

Quadrature Digital Up Converters

QDUC

-

Analog Devices Inc.

QDUC - Analog Devices Inc.

Analog Devices digital up/downconverters serve as the frequency translator and digital filter between data converters and DSP blocks. These innovative products enable highly programmable and configurable receive and transmit signal chains, allowing multichannel, multicarrier radio platforms in 3G wireless base stations. They also meet the digital data conversion requirements for many other communications applications.

Product

Low Noise Triple Band Voltage Controlled Oscillator

-

Teledyne RF & Microwave

Teledyne RF & Microwave

This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.

Product

Current Converter AC

NMTI 2

-

Metra Blansko a.s.

NMTI 2 - Metra Blansko a.s.

A modern multipurpose quantity-to-current loop converter designed for installation in switchboards.

Product

POWER Converter AC

NMTP

-

Metra Blansko a.s.

NMTP - Metra Blansko a.s.

The NMTP AC power converters with two mutually independent analogous outputs serve to convert single-phase or three-phase AC power into current or voltage analog signals. The A output is used for active power measurements, the B output for reactive power measurements.

Product

File Import Tool For Importing And Converting STIL, WGL, VCD/EVCD Vectors

DIOEasy-FIT

-

Marvin Test Solutions, Inc.

DIOEasy-FIT - Marvin Test Solutions, Inc.

Marvin Test Solutions' DIOEasy-FIT option offers test engineers a software tool set for importing and converting STIL, WGL, VDC/EVCD files to a Marvin Test Solutions' digital instrument file format. DIOEasy-FIT works in conjunction with Marvin Test Solutions' DIOEasy waveform display and editor software which provides an efficient tool set for developing, debugging, and executing digital test vectors for all MTS dynamic digital instruments.

Product

50 Ω High Voltage Pulse Generators

-

High Power Pulse Instruments GmbH

High Power Pulse Instruments GmbH

50 Ω High Voltage Pulse Generators by HPPI GmbH

Product

Low Noise High Precision High Voltage Amplifier

WMA-280

-

Falco Systems

WMA-280 - Falco Systems

The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.

Product

Non-Contact Voltage Tester

2AC

-

Fluke Corporation

2AC - Fluke Corporation

The Fluke 2AC is the latest addition to the VoltAlert™ AC non-contact voltage tester family. It is designed to be pocket-sized and easy to use. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip, or power cord where voltage is present. The 2 AC is always on, with a battery check function to make sure the tester is working properly.

Product

Binary BCD Converters

-

Computer Conversions Corporation

Computer Conversions Corporation

The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.

Product

High Voltage Divider

-

HIGHVOLT Prüftechnik Dresden GmbH

HIGHVOLT Prüftechnik Dresden GmbH

Is a passive linear circuit that produces an output voltage (Vout) that is a fraction of its input voltage (Vin). Voltage division is the result of distributing the input voltage among the components of the divider. A simple example of a voltage divider is two resistors connected in series, with the input voltage applied across the resistor pair and the output voltage emerging from the connection between them.

Product

Retractable Cable + Automotive Voltage Tester With Magnet Adsorption

3703

-

Peaceful Thriving Enterprise Co Ltd

3703 - Peaceful Thriving Enterprise Co Ltd

*Check on 6, 24 and 48V DC systems.*Used as an extension cord for testing electrical circuits in cars , trailer, boats.

Product

Frequency Converters & Transceivers

-

Mercury Systems, Inc.

Mercury Systems, Inc.

Mercury Systems’ converter and transceiver products are at the forefront of SWaP-optimized RF integrated products. Through substantial R&D investment and a library of building blocks, Mercury Systems has the capability to rapidly execute on the most complicated of custom transceiver designs. As the OpenVPX industry leader, Mercury Systems knows how to make integration into your system a breeze.

Product

DC/DC Converter 120 W

CTS-120-6874-D

-

ELMA Electronic, Inc.

CTS-120-6874-D - ELMA Electronic, Inc.

DC/DC converter with 120 W from Premium | input ranges 43.2 - 90 VDC | output 12 V | operates in temperatures from -25 - +85 °C | designed according to EN50155

Product

​RF Converters

-

Teledyne Lincoln Microwave

Teledyne Lincoln Microwave

Typically designed for radar or wideband EMC test applications, our frequency converter modules are designed for the conversion between complex baseband waveforms and higher transmitted frequencies. These modules are ideal for integration with digitising modules.

Product

RS-232 to RS-422/RS-485 Converter

ND-6520

-

ADLINK Technology Inc.

ND-6520 - ADLINK Technology Inc.

ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.

Product

High Voltage Holiday Detector

AP-W

-

Tinker & Rasor

AP-W - Tinker & Rasor

The Model AP/W can be customized for many applications, including In-Plant operations. Power from 115v or 230v AC Connection for external klaxon Custom cables for automated systems We can customize the AP/W to fit your needs. Contact us for details!

Product

Throwdown Fiber Transport & Converters

NanoBriX Series

-

Multidyne

NanoBriX Series - Multidyne

We often forget all that happens along the media signal journey. Video and audio signals are converted, equalized and re-clocked as they move on and off fiber-optic networks. These same signals are manipulated and multiplexed as they are distributed through studio, venue and campus infrastructure on their way to headends and destination points. Audio signals are embedded and de-embedded alongside video streams, and properly mixed for varied broadcast and playout services. It’s almost too much to keep up with. MultiDyne’s NanoBrix Series assures that these many stages of the signal lifecycle are reliably addressed in one complete family. NanoBrix offers a comprehensive product line of miniature, rugged, quick-connecting throwdown solutions for temporary or permanent applications, including live TV productions, sporting venues, and broadcast facilities.