Mil-Std-1760
military aircraft and their stores electrical interconnection system.
See Also: MIL-STD, Mil-Std-1553
-
Product
Coax, Contact, Receiver, 20/26 GHz, SF142B, 90 Series modules only
610102109
Coax Contact (Receiver)
Primary mating contact 610102110. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 OhmsFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications SF142B Environmental SpecificationsOperating Temperature -65°C to +125°Vibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
Product
Intelligent Interface Card
IIB-1553-PC104
-
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
Product
PCI Generic Carrier Cardfor PMC (PCIbus Mezzanine Card) Modules
ACP-1
-
PCI generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Isolated
SC2
-
Module SC2 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications.
-
Product
Rugged Ethernet
ES-1553RUNET/Px(S)
-
The ES-1553RUNET/Px is an intelligent, rugged single channel, MIL-STD-1553 adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in rugged environments.The ES-1553RUNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Single Function MIL-STD-1553 Test & Simulation PCIe Card
ASE1553M-x
Simulator
Single Function MIL-STD-1553 Test and Simulation module for PCIe with 1, 2 or 4 dual redundant streams.
-
Product
Active Monopole Antenna
AM-741
-
The 41 inch Monopole antenna is required for making electric field emission measurements below 60 MHz per Military standards (MIL-STD-461) and FAA (DO-160) specifications. This antenna is for emissions measurements only. It cannot be used for transmitting. The Active Monopole antenna is generally used in a shielded room or in a screen room, with the equipment under test (EUT) placed on a metal ground plane. The 41 inch rod and the ground plane behave electrically as though a mirror image of the rod were located below the ground, and the ground removed. Since the stainless steel plate does not have enough surface area to mirror the entire 41 inch rod, it is bonded to the surrounding ground plane during use. The AM-741 is battery powered to prevent measurement errors that maybe caused by external power cables. The ANSI equivalent capacitance substitution (ECSM) method is the recommended method for calibrating AM-741 monopole antenna. The individual calibration data will be included with each antenna.
-
Product
PC Card
Flex1553 PCIe
-
The Flex1553-PCIe is a PCI Express card supporting 1, 2 or 4 Dual Redundant MIL-STD-1553 buses, 1553 Enhanced Bit Rate, ARINC 429 and Discrete with precise timing and flexible programming. The PCI Express card with a robust 19-inch connect panel for easy and long-lasting connectivity.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
42-739-006
Multiplexer Module
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
Rugged MIL-STD-1553 Ethernet Data Logging & Acquisition Module
eDAQ-1553-FQ
-
Avionics Interface Technologies
(2) Redundant MIL-STD-1553 bus interfaces (Transformer and Direct coupled) - (2) 10/100/1000-BASE-T Ethernet LAN Interfaces with POE - (2)PCM Output (up to 20Mbps) - (1) RS-232 Serial Interface - Streams select MIL-STD-1553 bus data & parameters over Ethernet - Supports Data Logging, Data Analysis, and Flight Test Data Recording applications - Timestamp synchronization to IEEE 1588 and IRIG-B - Full MIL-STD-1553 Bus Error Detection - MIL-STD-810G Compliant - Small, compact package 6in X 1.9in X 1.5in
-
Product
MIL-STD-1553 Two-Channel PMC Board
BRD1553PMC-STD-2
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains two channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
Type 12R2, 12U, 19" Rackmount, MIL-Rugged, Vertical
12R2-12U-V
-
The 12U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.
-
Product
Horn Antennas
-
Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. Most compliance standards now require the use of such antennas. The latest version of Mil-Std 461E states the used of broadband double ridge guide horn antenna as the antenna of choice for frequencies above 200 MHz.
-
Product
Aerospace and Defense Software (3000A/T/G X-Series)
D3000AERB
-
MIL-STD 1553 and ARINC 429 triggering and analysis for the InfiniiVision 3000A, 3000T, 3000G X-Series oscilloscopes, along with mask testing, advanced math, video analysis, and more.
-
Product
PCI Express Mini Card For MIL-STD-1553 Test And Simulation
AME1553-1
-
MIL-STD-1553 Test and Simulation PCI Express Mini Card with 1 Dual Redundant channel plus 2 discrete Input, 2 discrete Output channels.
-
Product
MIL-STD-1553 Products
-
- Wide Selection of MIL-STD-1553 COTS Interface Cards/Boards and Real-Time Appliances- Packetizing Engine – 3rd Gen Design Common Data Packet (CDP) Architecture- Portable FPGA AltaCore Design – Reduced Parts Obsolescence Risk
-
Product
MIL-STD-1553 Interface Board
EXC-4000VME/MCH-x / EXC-4000VXI/MCH-x
-
The EXC-1553VME/MCH and EXC-1553VXI/MCH cards are based on a MIL-STD 1553 certified "Summit" chip used in many flight critical systems. Each dual redundant channel supports both MIL-STD-1553A and MIL-STD 1553B protocols. Up to eight channels may be programmed individually to operate as a Bus Controller, Remote Terminal, Bus Monitor, or Remote Terminal / Concurrent Bus Monitor. The 32 K x 16 of RAM allotted to each channel for the storage of data and control parameters may be updated in real time.
-
Product
Voltage Controlled Oscillators
-
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
Product
Coax, Contact, ITA, 75 Ohm HD, sm59/U Belden 1855A, 3 GHz
610102132
Coax Contact (ITA)
Primary mating contact 610102133. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter contact – BeCuContact Plating Center conductor shield –30µ” Au over 100µ” NiContact Termination Center conductor - SolderShield - CrimpInsulator PTFEMating Force 2.0 lbs max [0.91 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR ≤ 2.26 @ 3 GHzInsertion Loss -0.86 dB MaxDWV 800 VDC min.Contact Resistance 5 mΩ center/ 3 mΩ outer Cable Specifications sm59/U Belden 1855AEnvironmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
Product
Hold-Up Power Module - PCB Only Without Cover
055-149
-
Hold-Up Power Module for voltage input of 16 to 36VDC provides maximum power output of 330W for 50ms per MIL-STD 704 / DO160. Board can be ordered as fixed-mount or plug-in version.
-
Product
Micsig Smart Oscilloscope
STO1000C/E
-
Shenzhen Micsig Instruments Co., Ltd.
*Up to 70Mpts memory depth, Zoom into a selected part of the captured waveforms to get more details. *Support serial triggering and decode (I2C, SPI, RS232/UART,CAN, LIN) and Aerospace and defence (MIL-STD 1553, ARINC 429). Two formats to display decoding, text and graphic.
-
Product
USAF Targets
-
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
-
Product
Biconical Antennas
-
For many years most standards called for the use of a half-wave dipole antenna set for frequencies above 80 MHz. However, to reduce test time, broadband antennas such as the biconical antenna and log periodic antennas began to be accepted. Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. A.H. Systems'' 7 models of Biconical Antennas operate efficiently over the frequency range of 20 MHz to 18 GHz. Suitable for FCC, MIL-STD, VDE, TEMPEST, and immunity testing, each Biconical antenna will provide reliable, repeatable measurements.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Vertical
12R2-8U-V
-
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
85W to 120W - Single Output
HQA Series
-
*Standard Quarter Brick Footprint*9-40 Vdc, 18-40 Vdc Inputs*3.3, 5, 12, 15, 24, 28, 48 Vdc Outputs*2250 Vdc Isolation*-55 to 115°C Baseplate temperature*MIL-STD-461; 1275; 704; DO-160*No Optocouplers used
-
Product
Unclamped Inductive Load Tester
ITC75300
-
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
Product
Standard And Custom Targets
-
Santa Barbara Infrared manufactures a wide range of targets for visible, and infrared/FLIR electro-optical testing. These targets complement our complete line of Visible and IR test products. Our targets are designed to function with one of SBIR’s target wheels. Utilizing a variety of manufacturing techniques, including conventional machining, photochemical etching, electro-deposition, electrical discharge machining (EDM) and laser cutting. SBIR targets are manufactured to exacting mechanical tolerances. SBIR manufactures all of the targets specified by MIL-STD-1859 and the Tri-Service Guide for thermal imager testing.
-
Product
Transient Pulse Generator
8282-1
-
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
