-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
PXI 32 x SPDT Reed Relay
40-110-121
Relay
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
Flexible 32-bit PCI to x1 PCI Express Adapter
SKU-049-0X
-
The Flexible 32-bit PCI to x1 PCI Express Adapter (Adapter) was designed to expand the 32-bit PCI bus into an x1 PCI Express bus. It allows you to connect the x1 PCI Express expansion board to the motherboard PCI connectorThe Adapter includes an x1 PCI Express adapter board, 32-bit PCI host board and PCI Express Flat cable.
-
Product
25-Pin D-Type Female Connector Block
40-965-025-F
D-Sub Female Connector Block
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Serial To Digital Interface MiniBox™
-
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
M2P.6546-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Mechanical Signal Relays (2A Or Less)
-
Panasonic Industrial Devices Sales Company of America
Mechanical Relays that can switch up to 2A. Ideal for low load switching, signal control, etc. Features include gold contacts, stable contact resistance, fully sealed construction, Form C contact arrangement, available latching and low operating power, and compact size for optimal board space usage. Applications include: AC Control, Communications, Security, Measurement Equipment, Audio Visual Devices and Automotive.
-
Product
Multipurpose Debug Board
DB40 Debug Module
-
The DB40 Debug Card is designed for debugging of COM Express and PC/104 boards. It includes the following features: - Port 80/81 decoding for Power On Self Test (POST) via LPC - Interface to SPI Flash for BIOS update - Interface to Board Management Controller (BMC) for update - Power and Reset buttons and status LEDs The DB40 Debug card can only be used on products that have the appropriate FFC debug connector designed for this purpose. (Includes DB40 Debug Module, two 40-pin FFC cables, and 14-pin cable for SP100 DediProg USB to SPI programmer.)
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - PCIe
Model 78132
-
Model 78132 is a member of the JadeTM family of high-performance PCIe boards. The Jade architecture embodies a new streamlined approach to FPGA-based boards, simplifying the design to reduce power andcost, while still providing some of the highest-performance FPGA resources available today. Designed to work with Pentek’s new NavigatorTM Design Suite of tools, the combination of Jade and Navigator offers users an efficient path to developing and deployingFPGA-based data acquisition and processing. The 78132 is a multichannel, high-speed data converter with programmable DDCs (digital downconverters). It is suitable for connection to HF or IF ports of a communications or radar system. Its built-in datacapture feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
-
Product
Indoor Gunshot Detection & Localization
SHOTPOINT
-
Shotpoint’s indoor sensor includes the basic sensor board in a rugged plastic enclosure with an additional PoE module. The enclosure includes a mounting ring that attaches to a 1-gang electrical box or low voltage frame for easy mounting to walls and/or ceilings. Two(2) sensors with 165ft maximum spacing provide total area coverage and peace of mind in any indoor space.
-
Product
RUB-01
Rub Tester
-
Jinan Leading Instruments Co., Ltd.
RUB-01 Rub Testerisapplicable in abrasion resistance test of printing works, light sensitive layer of PS boards, and coating layers of relative products. It can help users toanalyze the affairs of lower abrasion assistance, ink layer falling-off, lowerprintable of PS boards, and rigid of coating layers of other products.
-
Product
SparkFun MicroMod GNSS Carrier Board (ZED-F9P)
-
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
-
Product
Digital Vision Microscopes
-
Sinowon Innovation Metrology Manufacture Ltd.
Video Microscope is widely used in the inspection of electronic industry production line, printed circuit board, weld detects ( such as wrong printing, edge collapse,etc)during printed circuit component, PC Board, VFD, and the identification of printing grid and painting, etc. It can display the zoom out image on the screen and save, magnify and print.
-
Product
DSP Based Serial Communication Board
CPCI-ISC8
Communications Module
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
Laser Board
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
Dust Collector Timer Controller
DCT1000
-
Simplify your on-demand cleaning requirements with the Series DCT1000 Dust Collector Timer Controller. Relying on one timer board for on-demand and continuous cleaning applications, the DCT1000 eliminates external devices such as pressure switches, relays and timers.
-
Product
Circbord
8022
-
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
Product
Dynamic Digital I/O (3U), 32 Ch., Per Pin Control, Up To 100 MHz W/256MB Memory & LVDS
GX5292
Digital I/O
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch., per Pin Control, up to 100 MHz w/256MB Memory & LVDS
-
Product
Compatible Adapter Carrier
PCI2PC104p
-
Use your PC/104p boards in a standard PC. Two orientations supported for production mode and test.
-
Product
Silver Plated Test Points
-
The fabricators of SMT printed circuit boards may take advantage of the convenience of field testing with the unique loop design of Components Corporation's TP-107 and TP-108 series of surface mounted, printed circuit test points is now available in silver-plate for outstanding reliability. All products are RoHS and REACH compliant.
-
Product
FPGA Image Processing (IP) Development Kit
ProcVision
-
Gidel’s Vision Pro Development Kit is an optimal solution for developing,validating, demonstrating and evaluating Image Processing (IP) andpipeline designs on FPGA.The suite is designed to provide a complete and convenient envelop enablingthe developer to focus strictly on the proprietary image processingdesign. The entire Vision Pro flow is within a single FPGA, independentof the final target application(s). The Vision Pro flow is composedof a pipeline that streams simulated data to the user image processingdesign under test (DUT) and then captures the design’s output streamfor displaying, storing, analysis and/or co-processing on host software.The entire process is performed on a single FPGA without the need foradditional peripheral connectivity or tools.Vision Pro suite is plug-and-play enabling the developer to begin at oncethe IP design development and validation. A simple design example providesthe developer immediate hands-on familiarization with the systemflow and supporting tools. The final design can be ported to any IntelFPGA device or other vendors’ devices (FPGA or ASIC) by replacing basiclibraries. To significantly reduce compilation time, initial design developmentmay be on a small FPGA device and later compiled for the targetdevice(s). The target implementation may use any FPGA board. For a fullImaging/Vision system solution, Gidel offers a number of off-the-shelfgrabbers and FPGA accelerators that are designed to utilize these imageprocessing blocks and Gidel Imaging Library (GIL).
-
Product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 5 Slot, to (1) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1)
510171104
PCB Adapter (ITA)
A small, modular PCB board that connects high speed data inserts (VTAC) to a single USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules.
-
-
Product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
-
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
Digital IO
PA32IX
Digital I/O
The PA32IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32IX also supports deep pattern memory by offering 64 M of on-board vector memory with static per pin direction control and with test rates up to 50 MHz.
-
Product
Backplane Twinax Connectors
-
We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.
-
Product
2-Axis High-Resolution Laser Axis Board for VME
10898D
Laser Board
The 10898D 2-axis high-resolution laser axis board provides the same resolution as the Keysight 10897D high-resolution laser axis board with increased slew rates and reduced noise. The increased stage velocity limits and low noise compared to previous laser systems offer premium positioning repeatability and accuracy for advanced applications such as IC fabrication equipment.
-
Product
Development System
FE-51CC01
-
* Emulates Atmel T89C51CC01/2 and T89C51AC2, T89C5115 * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
