Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Single 24x6 1-Pole High-Density PXI Matrix Module
40-520-302
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Single 32x4 1-Pole High-Density PXI Matrix Module
40-520-401
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Enclosure, 9050, Hinged Cover, 12" Depth
410112519
Enclosure
Enclosure, 9050, Hinged Cover, 12" DepthNot compatible with 9050 ITA frame p/n 410104110 or any older model 9050 ITA frame not matching the current height of 9050 ITA frames of 14.57". Questions? Contact Us before purchase.
-
Product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
-
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
Product
Quick-Release Universal ZIF
Series X57X
-
Quick-Release Universal Zero Insertion Force Dip Test Socket. Aries Universal Test Socket accepts devices on .300 to .600 [7.62 to 15.24] centers. Swing quick-release handle down to open contacts and insert device. Release and handle automatically returns as contacts close onto device leads.
-
Product
Wafer Prober
Precio XL
-
Fully automated 300mm wafer prober. The system achieves high productivity, excellent contact performance, improved cleanliness, and short lead time, and offers a number of high value-added functions as options.
-
Product
68-Pin Micro-D Male Solder Bucket With Backshell
40-962B-068-SB-M
SCSI Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
PXI Single 8 Channel Switch Simulator
40-485-021
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Power Module Test Cells
-
SPEA’s Power Module Test Cells are the complete industrial equipment oriented to the production test requirements of IGBT semiconductor power modules for consumer, transportation, energy production, industrial applications.SPEA’s Power Module Test Cells provide a turnkey solution for the automated handling, contacting and testing of these products, with the capability to force and measure the very high current (up to 1000 A) and voltage (up to 2500 V) values required for a complete, reliable test.
-
Product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
-
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
-
Product
Test and Analysis
-
ESDEMC Technology will calibrate; the Contact Mode ESD current waveform and tip voltage to 4 GHz and 30 kV, the frequency response of ESD Target & Adapter Line to 4 GHz, and the DC Resistance
-
Product
Relay Modules
DN-SSR4
-
The DN-SSR4 includes 4 normally open, Form A, solid-state relays. The user can use the DN-SSR4 to switch high voltage load up to 240VAC and up to 4A. Four enunicator LEDs (one for each relay) light when their associated relay is activated. Each output is equipped with a varistor that shunts the surge voltage of the inductive load or electromagnetic brake to protect the relay contact point. All relay control and relay outputs are accessible through the wiring terminals.
-
Product
Mini Coax, Contact, ITA, RG316 & 178, Solder Sleeve
610103158
Coax Contact (ITA)
Contact, ITA, Mini Coaxial, RG316 & 178, 50 MAU, Solder Sleeve
-
Product
IBM PC-XT, Vectorbord Plugbord
4613-1
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Voltage and ground buses around board perimeter on both sides. Auxiliary bus line along lower edge of board on both sides. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
Probe Cards
-
PICOPROBE® PROBE CARDS by GGB Industries, Inc., allows for more chip design flexibility because each probe card is custom configured to your circuit for testing wafers on either manual or automatic probe stations. Probe cards with complex layouts consisting of numerous DC contacts and multiple microwave probes with operating frequencies of 40, 50, 67, or 110 GHz can be custom fabricated quickly and inexpensively.
-
Product
Rotation Meters
-
Here you will find many types of rotation meter. There are different ways of measuring revolutions within the industrial sector, either optically or mechanically. The PCE-151 handheld series of rotation meter with Rotation Meter OverviewRS-232 interface can measure revolutions and velocity and store the readings onto a computer using software which comes with the device. The handheld digital rotation meter is ideal for measuring velocity and revolutions in research and maintenance. The PCE-T236 rotation meter measures velocity both by contact and non-contact and is good value for money.Non-contact measurement of velocity is done with the help of reflective tape. For a device that can be installed for measurements over a period of time, we recommend the PAX I rotation meter.
-
Product
Godzilla High Current Probe, 100 Amp
HC375
High Current Probe
Current Rating (Amps): 100Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 360Full Travel (mm): 9.14Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,110Overall Length (mm): 78.99
-
Product
Micro Power, Contact, Receiver, 21 Amp, PCB Mount
610142102
Power Contact (Receiver)
Primary mating contact 610143101. (May mate with other ITA contacts, as well.)
-
Product
Safety Critical Miniature Relays
CU-U Series
-
The CU-U is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
PXI Single 44 x 4 Matrix 1 Pole Screened
40-523-021-S
Matrix Switch Module
The 40-523 module is configured as a 44x4 high density matrix with available reedrelay formats of 1-pole, 2-pole and 1-pole screened. The screened version is suitablefor switching signals up to 50MHz. Model 40-524 is a similar matrix, available insingle pole 46x4 format. Typical applications include signal routing in FunctionalATE and data acquisition systems. These PXI matrix cards are constructed using highreliability Ruthenium Electro-Plated Reed Relays, offering >10e8 operations togive maximum switching confidence with long life and stable contact resistance.
-
Product
Fine Pitch Test Probes
-
Micro probes allow very fine pitch testing ranging from 0.13mm to 0.35mm pitchLow Resistance, Low inductance, High FrequencyWide selection of plating options to optimize contact challenges and maximize probe lifeTri-temp applications – 55°C to 155°C
-
Product
Passive Component Integration - PXIe
Passive Series
Passive Component Integration
The Passive PXIe module is a highly customizable PXIe module that can integrate the passive components of your choice.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
Product
Low Resistance Or Continuity Testing
-
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
Product
20-Pin GMCT Female Connector, 16A, With Backshell
40-960-020-16A-F
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. Also included is the backshell with screwlocks and cable clamp.
-
Product
Micro-Ohmmeters
RMO-A Series
-
The RMO-A is a portable micro-ohmmeter designed for contact resistance measurements of switchgear during manufacturing, commissioning and maintenance stages. This micro-ohmmeter is widely used by medium and high-voltage circuit breakers manufacturers. Other typical applications are testing of disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. It accurately measures not only in factory environments but also in high-induction fields and substationsThe RMO-A series contains 6 models, rated from 100 A (RMO100A) to 600 A (RMO600A). The RMO500A (formerly CPM500) is our best seller, with 500 A ripple-free current and weighs only 8 kg.Although placed in a very portable and lightweight metal housing, RMO-A micro-ohmmeters have very high output power capabilities. They can generate 600 A test current continuously for up to 20 s. You can test with current up to 100 A without rest time. High output voltage enables a wider measurement range at the highest test currents, as well as the use of thinner/longer test cables. For testing with 100 A, 20 m test leads can be provided with only 16 mm2 cross-section.RMO-A micro-ohmmeter generates a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the RMO-A ramps up with increasing current before measuring and decreasing current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.An additional option is a built-in High Precision module suitable for measurement of very low resistances, ranges from 1 to 30 µΩ, with 0,01 µΩ resolution.These instruments can store up to 500 measurements in internal memory. A built-in thermal printer is available as an option.Our free DV Win software communicates with the RMO-A micro-ohmmeters via USB or RS232 interface. It allows you to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.
-
Product
Thermal Test Boards
-
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
Product
Analog & Digital I/O Modules
-
USB analog and digital I/O modules are a complete family of data acquisition modules for use in process control systems. The analog input modules can measure process signals such as DC voltage, thermocouples, 4-20mA current loops, discrete contact closures.
-
Product
XRF Systems
OEM Solutions
-
Amptek offers a complete line of OEM detectors, preamplifiers, digital processors, and power supplies, and can work with you to help develop custom solutions unique to your needs. We provide established and emerging OEM customers a fast track to the market with our modular systems that will meet current needs, while being flexible enough to adapt to your product roadmap. The below options are typical configurations. Please contact us for custom solutions.
