Verifiers
-
Product
PXI Resistor Module 4-Channel 1R to 510R
40-293-014
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
Stand Alone Wafer Sorter
MicroSORT
-
The Microtronic MicroSORT semiconductor wafer sorter is designed to maximize throughput while minimizing wafer handling in a user-friendly operating environment. This stand-alone semiconductor wafer sorter enables sophisticated semiconductor wafer sorter routines for up to 4 wafer-cassette platforms. MicroSORT semiconductor wafer sorter reads OCR scribes from the top, bottom, or simultaneously, allowing for enhanced semiconductor wafer tracking and sorting. The MicroSORT semiconductor wafer sorter’s basic functions include the ability to move, compress, randomize, find, align, verify, and split semiconductor wafer lots. With our virtual tweezer mode, an operator can click on wafer icons to move wafers between cassettes, read semiconductor wafers, and swap wafer positions.
-
Product
28 Days Test Bench (Single Phase & Three Phase)
-
The SCR Elektroniks 3 station MCB 28 Days and Temperature Rise Test Bench is economically designed to verify the 28 Days Test (21 hr ON, 3 hr OFF Test) as per clause 9.9 of IEC 60898-1 and Temperature Rise of the parts of a Circuit Breaker specified in Table 6 of clause 8.4.1 measured under the conditions specified in clause 9.8.2 of IEC 60898-1.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Compact, Easy To Use Tester.
Eye-BERT 40G
-
The Eye-BERT 40G packs 40Gbps of test capability and a color touch screen into a compact, easy to use tester. The Eye-BERT 40G offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of QSFP transceivers as well as link verification and performance testing all in a single unit. The automated QSFP test feature also allows the user to quickly verify transceiver performance and automatically generate a report complete with unit serial number.
-
Product
Universal In-System Programming Tool
ScanExpress JTAG Programmer
-
ScanExpress JTAG Programmer is a universal in-system programming (ISP) solution designed for convenience and versatility—a modular, multi-functional, and high-performance tool to program, read, and verify Flash memories, serial EEPROMs, CPLDS, FPGAs, and more.Like all Corelis ScanExpress family products, ScanExpress Programmer is a tool for all phases of the product life cycle—whether programming early code during product development, programming production code during manufacturing, or reprogramming units out in the field, ScanExpress Programmer is designed to fit all in-system-programming needs.
-
Product
Proximity Voltage Detectors
-
Verify the presence of voltage without contacting the conductor. Audible and visual alert when voltage is present. Powered by a rechargeable Li-Ion battery. HI/LO proximity voltage detector with two voltage ranges, 50V-4kV and above 4kV.
-
Product
Waterproof EC Tester Low with ATC
ECTestr Low
-
ECTestr Low tester series can measure natural water, verify reverse osmosis system operation and tap water quality. Check nutrient solution concentration in hydroponics applications.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PNA-X Microwave Network Analyzer, 8.5 GHz
N5249B
-
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Variable Fiber Optic Attenuator
-
Variable fiber optic attenuator could help simulate distance or actual attenuation in the fiber optic testing work by inserting a calibrated attenuation into the link. By using the variable fiber optic attenuator, technicians could verify the power margin received by testing the fiber optic link power budget. Variable fiber attenuator can help user vary the light power injected from a light source into the optical fiber. Important parameter of variable fiber attenuator include its insertion loss, reflection loss and attenuation range.
-
Product
1500V Multifunction I-V Curve Tracer
SOLAR I-Ve
-
SOLAR I-Ve allows both testing a single-phase (three-phase with optional MPP300) photovoltaic system and verifying I-V curve. Thanks to remote unit SOLAR02, it is possible to test the system complying with the requirement of simultaneity as provided for by the reference standard. SOLAR02 is a datalogger which, synchronized with SOLAR I-Ve, acquires the data relevant to irradiation and temperature while tests carried out by SOLAR I-Ve are carried out.
-
Product
Logic Analyzer Probe
FS2521
-
The FS2521 is a logic analyzer probe used to test DDR4 SO-DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4164A logic analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR4 SO-DIMMs. Now qualified at 3200MT/s
-
Product
EXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5171B
-
Achieve faster throughput and greater uptime with the cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading output powerThoroughly verify receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm
50-294-033
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Ultrasonic Leak Detector
ULD-420
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
Product
MPO Visual Cable Verifier Kit
KI-TK832
-
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
Product
2.5mm Test Rod Test Probe Needle
CX-4C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
Product
PNA Microwave Network Analyzer
N5227B
-
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Advanced Boresight Equipment)
ABE®
-
The ABE® (Advanced Boresight Equipment) is a common boresight system used to align and harmonize various commercial and military aircraft platforms. The system works in all operating environments, including concurrent aircraft maintenance and assembly, high winds, cramped and cluttered workspaces, and in extreme temperatures. This commercial, state-of-the-art, gyro-stabilized, electro-optical, angular measurement system is designed to align systems on any land, sea or air vehicle. Our system provides an accurate, repeatable and verifiable solution.
-
Product
MIMIC sFlow Simulator
-
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
Video and Protocol Analyzer
-
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
Product
Return/Insertion Loss Meter
CA6034
-
The CA6034 optical return loss/insertions loss meter is an intergrated meter for optical fiber network, and cable manufacturere to verify the quality of finber leads, with the features of handhel, intelligent and multi-functional.
-
Product
Calibration Executive Software
CalEasy Series
-
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
Product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm - SPST
40-294-112
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
HARDNESS TESTING
-
Hardness testing is a basic test used to verify raw materials or as a quick check for materials that fail or aren't performing as expected. Hardness tests quantify the resistance of a material to plastic deformation and is available as microindentation or macroindentation.
-
Product
Customer Specific Tests
-
No matter whether you have developed a product without an underlying standard or extended a product beyond the standard – we verify your product to see if it conforms to the characteristics specified by you.
-
Product
PXI Resistor Module 4-Channel 1R to 127R
40-293-012
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
