Voltage Regulators
-
Product
Thermal Voltage Converter
1395B
-
The 1395B TVC. Has better thermal stability than it's predecessor. Measuring ac voltages between 20 Hz and 100 MHz with increased accuracy and reliability. The 1395B can be used as a primary ac voltage standard and/or standard for the calibration of ac calibrators and voltmeters.
-
Product
Eight-channel USB Voltage and Thermocouple DAQ
Model DI-2008
-
Includes DI-2008 instrument, WinDaq software, calibration certificate, terminal screwdriver, and USB cable (6-feet). Eight differential and isolated analog input channels. Seven bi-directional digital input ports, including: Counter input for totalizing applications, Rate input for frequency/flow/rpm applications. ChannelStretch™ channel expansion to 128 analog and 112 digital channels. Programmable voltage and thermocouple measurements per channel. 10 mV to 50 V programmable range per channel in 12 steps.
-
Product
High Voltage Probe Meters
-
Shanghai Beha Electronics Co., Ltd.
*High voltage test probe *is a high voltage probe that is used with Oscilloscope● Attenuation Ratio: 1000:1*Measuring range: AC 20KV/DC 30KV
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-335-HI
Programmable Resistor Module
The 40-230-335-HI (PXI) and 42-230-335-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 201kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Relay Testing Voltage Source
PTE-FCL
-
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCL upgrades the PTE-100-C to the PTE-100-C Plus model.
-
Product
High Voltage 50 Pin D-Type Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Product
4.0 GHz, 0.6 pF, 1 MOhm Active Voltage Probe
ZS4000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.6 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS4000 is ideal for 2.5 GHz and 4 GHz oscilloscopes.
-
Product
High Voltage Capacitance & Tan Delta Test Set
-
*Aesthetically designed Single Unit consisting of Measuring Bridge, Power Supply with in-built Standard Capacitor. Ideal for field /portable applications.*Highly compact & Portable – Approx 66Kgs only.*Advanced Protection Circuitry –specially suitable for 400kV s/s applications.*Successfully passed all required EMI/EMC Tests at SAMEER Chennai IEC 61000-4-2;IEC 61000-4-3; IEC 61000-4-4; IEC 61000-4-5; IEC 61000-4-11;*Improved Plug-in type of “Power In” and “Gnd” connectors.*Preo 2 Stage RF Power line Filters incorporated for 230V Power Input and Bridge Power Input for improved EMI Power line Protection*Improved 2 sets of LV measuring cables.*Improved HV cable outer covering hosepipe for rugged field use.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-330-HI
-
The 40-230-330-HI (PXI) and 42-230-330-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-214-HI
-
The 40-230-214-HI (PXI) and 42-230-214-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-705-HI
-
The 65-231-705-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the multiplexer.
-
Product
AC/DC Programmable Hipot Voltage Insulation Tester 5KV
7122
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC Hipot & Insulation Resistance Tester can do hipot test and insulation resistance test
-
Product
FD-11601, 8-Channel, ±10 V Powered-Sensor Voltage Input Device for FieldDAQ
786374-01
Voltage Input Module
The FD-11601 measures up to eight channels with a voltage input range of ±10 V. Each input channel supports TEDS and provides 24 V DC to power external-powered sensors without additional power supplies. The FD-11601 features 24-bit resolution, simultaneous sample rates up to 100 kS/s/ch, and channel-to-channel isolation. It is IP65/IP67 rated to be dust-tight and water-submersible, operates in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11601 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11601 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11601 is ideal for test cell and outdoor environments.
-
Product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
-
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
High Voltage Pulse
-
For thicker coatings it has fully adjustable output voltage from 5 kilovolt to 25 kilovolts. For very demanding conditions, a sensitivity switch offers additional control.
-
Product
Probe Oscilloscope High Voltage
-
High voltage probes allow safe and accurate voltage measurement using your oscilloscope.
-
Product
High Voltage Insulation Tester
505
-
Simpson's Model 505 High Voltage Insulation Tester is capable of measuring insulation resistances from 10 kilohms to 1 teraohm with eight selectable test voltages up to 5000 V. As a safety feature, the insulation tester acts as an AC/DC voltmeter to measure the absence of voltage in networks up to 2000 V.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-336-HI
-
The 40-230-336-HI (PXI) and 42-230-336-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 2-Pole
40-321-124-HI
Multiplexer Module
The 40-321-124-HI (PXI) and 42-321-124-HI (PXIe) are single 9-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
LXI High Voltage Switching - 3-Bank, 1-Pole, 6:1 Multiplexer Plugin Module
65-231-710-HI
-
High voltage multiplexer plugin module capable of cold switching up to 7 kV and hot switching up to 5 kV.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 1-Pole
40-321-101-HI
Multiplexer Module
The 40-321-101-HI (PXI) and 42-321-101-HI (PXIe) are quad 5-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
Voltage Meter
МН32СМ
-
The mezzanine module (mezzanine) МН32СМ is designed to measure instantaneous voltage values over thirty two two-wire differential channels.
-
Product
Bench/System Precision Linear Regulated DC Power Supply With Digital Control, Single Or Triple Outputs, 105 To 242 Watts, With/without Remote Interfaces
QL Series II
-
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 1m, 29 Wires
A051KMR-F-HA100-29
Cable Assembly
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
Product
AC Voltage Proving Units
HLV-3
-
Standard Electric Works Co., Ltd
● Designed to proof. AC voltage detectors AC voltage testers● Compact, handheld, and easy to carry and use.● Battery operated.● LED indicates when power is "ON".● Normal 4mm test leads.
-
Product
High Voltage Optically Isolated Probe, 1 GHz Bandwidth. Includes soft-carrying case.
DL10-ISO
-
The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.
-
Product
Multi - Purpose Digital High Voltage Phasing Meter
Model KM-MPS-50K
-
Kusam Electrical Industries Limited
• AC 50kV and DC 50kV measurement with direct reading.• 4000-count LCD.• Input impedance : 400 Mohm• Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV, DC : 4.000kV / 40.00kV / 50.0kV• KM 50K must be connected with an approved hot stick (Optional).• Check phases are "in-phase" or "out of phase".• Polarity indication : Positive / Negative• Backlight function.• Auto power off.• Power source : 1.5V(AA) alkaline battery × 2.• Low battery indication(Multi-level).
-
Product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
40-321-103-HI
Multiplexer Module
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-222-HI
-
The 40-230-222-HI (PXI) and 42-230-222-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
