Line
-
Product
VME Display And Bus Analyzer Module
VM-DBA
-
VM-DBA is a new test and diagnostic module for VME-bus systems which visualizes activities on all VME bus lines on the set of front-panel LEDs, but also allows one to digitize individual waveforms of all these lines into 2kBit -long storage memories, for a subsequent readout via VME or USB interfaces.
-
Product
Cooling Systems
-
Aerodyn Engineering designs and manufactures its own line of cooling carts. Our cooling carts will supply filtered coolant to the slip ring while in operation. Aerodyn Engineering’s cooling units are extremely reliable and are designed and manufactured with the highest quality components and craftsmanship available in the industry today. Magnetically coupled pumps are employed within our system to deliver the cooling fluid, with full user instruments showing flow rate and system pressures.
-
Product
Modular Spectroscopy Equipment
-
Sciencetech offers a large line of spectroscopy equipment, for an overview of Sciencetech''s modular spectroscopy equipment see the chart at the bottom of page
-
Product
Trackside Equipment
-
The Automotive assembly track lineside environment requires numerous amounts of tooling & equipment to ensure build phases are completed productively. Jackmark Engineering provides a wide variety of custom designed trackside jigs & fixtures, test leads and assembly aids including validation tooling to various assembly departments from HVAC to end of line.
-
Product
Filter Products
-
Although a primary building block for duplexers, multicouplers and preselectors, these cavities filters can be used individually or cascaded together to prevent interference or system clean up. Our cavity filter product line consists of four model types.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
Split-box Pipe & Cable Locator
-
Weshine Electric Manufacturing Co., Ltd
Pipe Locator is specially designed to detect pipes, sondes, telecommunication lines buried utilities. This device may detect buried power cables, CATV cables, gas and water pipes, sewer lines, telephone cables, fiber optic cables with sheath, sondes, inspection camera transmitters. The Transmitter emits a signal.
-
Product
Test Pattern GeneratorDelay & AV Sync Analyzer
VQDM-100
-
Versatile compact and robust multi-purpose tool for R&D and glass-to-glass QA/QCInstant visual-aural quality estimation plus automatic latency, AV sync and 3D LR sync measurementMulti-channel time-line analysis, including video frames continuity testing4 Light Sensors with vacuum caps, 4 Audio inputs (standard line levels)2 channels of AV timing analysis, simultaneous measurements of Video and Audio LatenciesReal time multi-channel data acquisition via USB portUnique sophisticated set of static and dynamic test patterns up to 1080p@60fps - see more details in separate VQL pageSource of VQDM, VQMA2, and VQMA3 Test Patterns for VideoQ AnalyzersMulti-format digital and analog AV outputs: HDMI, YPrPb, S-video, SPDIF, LR analog audioNetworkable unit, easy expansion with any external USB storage device: live clips, user content, etc.
-
Product
XRF Systems
OEM Solutions
-
Amptek offers a complete line of OEM detectors, preamplifiers, digital processors, and power supplies, and can work with you to help develop custom solutions unique to your needs. We provide established and emerging OEM customers a fast track to the market with our modular systems that will meet current needs, while being flexible enough to adapt to your product roadmap. The below options are typical configurations. Please contact us for custom solutions.
-
Product
Automatic Air Purging Tank
MF-015
-
If the fuel passing through a flow detector has mixing of air, the flow rate cannot be measured correctly. The MF-015 is an automatic air purging tank that uses a precision float valve. When fluid enters the flow line, the air is automatically purged to the atmosphere.
-
Product
Decade Box, Calibrated W/D & U, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL DU
-
The 72-7265 CAL DU from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Network Probe for TC-NT2
TC-TP1
-
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
Product
USAF Targets
-
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
-
Product
FASTCAM
1MP and 2MP Cameras
-
A leading line of high-speed, slow-motion cameras manufactured by Photron. The "1MP" and "2MP" designations refer to the cameras' image sensor resolutions, which are used to capture ultra-fast events at thousands of frames per second
-
Product
3D Machine Vision Process Control Solutions
-
In the age of automation and robotics, manufacturers utilizing automated dispensing in their assembly lines face growing challenges to maintain process control of their manufacturing processes. To eliminate errors and optimize product quality, they increasingly need the help of machine vision based “eyes of automation”. Whether manufacturing automobiles or medical devices, they need high-speed inspection tools to confirm the accuracy of their dispensing process and the overall quality of their products.
-
Product
Multifunction Calibrator 15 ppm Basic Accuracy
MC142
-
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
Product
Clamshell Type Mechanical Fixtures
-
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
Product
Cabinets
-
Elma has an extensive line of configurable, modular vertical 19" rackmount cabinets and consoles, rugged and mobile racks and carts, wall- and pole-mount enclosures to effectively house and protect sensitive and critical electronics. We can meet a wide range of requirements: challenging rugged environments found in defense and aerospace applications; exposure to harsh conditions found in outdoor or factory settings; or challenging thermal requirements faced by broadcast rooms, clean labs, data and telecom centers.
-
Product
Multifunctional testers
MI 3152 EurotestXC
-
MI 3152 EurotestXC is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN, TT and IT earthing systems are managed by a completely new user interface based on large colour touch screen display. A wide range of functions is included: from on-line voltage monitoring, phase sequence testing, varistor testing, earth resistance measurement, illuminance measurement and TRMS current measurement up to RCD tests, line and loop impedance tests, specific earth resistance measurements as well as ISFL measurements and the IMD tests.
-
Product
PXI Switches
-
The PXI general purpose switch modules deliver fast, reliable switching in a variety of configurations. Cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids with independent, single-pole, double-throw (Form C) or single-pole, single-throw (Form A) switches in a single PXI module. Choose between the high-speed, long-life reed relays capable of switching up to 100Vrms with up to 1A and 25W of power, or the higher power armature relays capable of switching up to 250Vrms, with up to 2A and 60W of power. The general purpose line also includes a module that offers the performance you need to switch heavy loads with up to 300W (DC resistive load)/1250W (AC resistive load).
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
Four Chanels Desktop CWDM/LanWDM DFB Laser Source
UC8134
-
The UC8134 Four Chanel Desktop CWDM/LanWDM DFB laser source offer superior performance for the test of CWDM, DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume couplers, transceiver/receiver and PLC production line application.
-
Product
PCIe Mini Module
PCIe-Mini-ESCC
-
The PCIe-Mini-ESCC module is a Dual Channel serial communication controller with 4K FIFO per Line. The PCIe-MiniESCC module is based on the Z85230 Enhanced Serial Communication Controller, with larger FIFOs and several SDLC improvements from Zilog.
-
Product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
-
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
DIN Rail Mount
-
Encore Electronics offers a complete line of compact, economically priced instrumentation packaged in standard DIN rail mounted enclosures. Our products include frequency to voltage converters, strain gage amplifiers, notch filters, accelerometer conditioners, and line drivers. Overall package sizes are 3.1″ x 3.3″ x 0.9″ tall (single wide) or 1.6″ tall (double wide).
-
Product
Verification And Print Quality Inspection Solutions
-
Integrate quality barcode verifiers within your production line using our robust barcode verification technology.
-
Product
Dip Clip, 14 Pin With Nickel Silver Contacts
5114
-
Pomona DIP Clip? test clips are designed fortesting dual-in-line IC packages on PC boards. Thesedevices incorporate many built-in features that assurea positive electrical connection as well as hands freetesting.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
The SoundCheck Amplifier
SCAmp Audio Test Amplifier
-
SC Amp is the world’s only dedicated audio test amplifier. Specifically designed for the audio test market, it incorporates several features unique to the needs of audio test and measurement, and unnecessary features found in regular audio amplifiers have been eliminated to keep production line operation simple and error-proof.
-
Product
Training Services
-
Austin Labs offers a full line of advanced protocol training classes. All classes are instructor led and guide students through the protocol specifications while using hands on labs with trace analysis to help students discover how the protocol is implemented. To create a reliable product, the user must first understand the technology and know how to use the tools needed to develop, test and debug the relevant host or peripheral specification. Here at Austin Labs we provide everything you need.
